Chief Manufacturing PCM User Manual

INSTALLATION INSTRUCTIONS

Instrucciones de instalación
Installationsanleitung
Instruções de Instalação

Istruzioni di installazione
Installatie-instructies
Instructions d´installation

Plasma Ceiling Mount

Spanish Product Description

German Product Description

Portuguese Product Description

Italian Product Description

Dutch Product Description

French Product Description

PCM SERIES

PCM SERIES Installation Instructions

Tighten Fastener

Apretar elemento de fijación

Befestigungsteil festziehen

Apertar fixador

Serrare il fissaggio

Bevestiging vastdraaien

Serrez les fixations

Сожмите Застежку

Loosen Fastener

Aflojar elemento de fijación

Befestigungsteil lösen

Desapertar fixador

Allentare il fissaggio

Bevestiging losdraaien

Desserrez les fixations

Ослабьте Застежку

Open-Ended Wrench

Llave de boca

Gabelschlüssel

Chave de bocas

Chiave a punte aperte

Steeksleutel

Clé à fourche

Открытый Рывок

Adjust

Ajustar

Einstellen

Ajustar

Regolare

Afstellen

Ajuster

Приспособьтесь

Hex-Head Wrench

Llave de cabeza hexagonal

Sechskantschlüssel

Chave de cabeça sextavada

Chiave esagonale

Zeskantsleutel

Clé à tête hexagonale

Главный ведьмой Рывок

Phillips Screwdriver

Destornillador Phillips

Kreuzschlitzschraubendreher

Chave de fendas Phillips

Cacciavite a stella

Kruiskopschroevendraaier

Tournevis à pointe cruciforme

Отвертка

DISCLAIMER

Milestone AV Technologies, Inc., and its affiliated corporations
and subsidiaries (collectively, "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject to
change without notice or obligation of any kind. Milestone makes
no representation of warranty, expressed or implied, regarding
the information contained herein. Milestone assumes no
responsibility for accuracy, completeness or sufficiency of the
information contained in this document.

WARNING:

follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.

WARNING:

for the installation of this kit can result in serious personal
injury or damage to equipment! It is the installer’s
responsibility to make sure the structure to which this mount is
attached can support five times the combined weight of all
equipment.

Failure to read, thoroughly understand, and

Failure to provide adequate structural strength

IMPORTANT WARNINGS AND

CAUTIONS!

WARNING:

serious injury or death if you do not follow the instructions.

A WARNING alerts you to the possibility of

WARNING:

serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to this mount does not exceed
200 lbs (91 kg).

Exceeding the weight capacity can result in

CAUTION:

A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.

LEGEND

2

WARNING:

The installer is responsible for verifying that the
1 1/2” NPT fixture this mount is installed on is capable of
supporting four times the maximum weight capacity of the
mount as stated above.

Installation Instructions PCM SERIES

x1

I/M

B (1)

3/16" (provided)

C (1)

D (6)

A (1)

TOOLS REQUIRED FOR INSTALLATION AND PARTS

DIMENSIONS

Figure 1

3

PCM SERIES Installation Instructions

1

(D) x 2

2

5

(A) x1

(D) x4

(B) x 1

2

1

Mount Assembly and Installation

1. Fold tube out until tube mounting bracket rests against
faceplate mounting bracket. (See Figure 2)

2. Secure tube to faceplate mounting bracket using 3/16" hex
wrench (C) and two 5/16-18 x 1/2" button head cap screws
(D).

3. Tighten all hardware.

Display Installation

If the mounting pattern of the display being installed is a VESA
standard 200 x 200 pattern the mounting buttons can be
installed directly to the back of the display. If the display has any
other mounting pattern an interface bracket must be obtained
before proceeding. Consult a Chief Customer Service
representative if an interface bracket is required by calling
1-800-582-6480 or visit www.chiefmfg.com.

Figure 2

4. Thread the tube assembly (A) onto 1-1/2” NPT.

NOTE:

5. Secure faceplate (B) to faceplate mounting bracket using

The product is suitable for use with a Listed ceiling
plate which can accommodate 1-1/2" NPT pipe, and
has a rated weight capacity of 200 lbs (91 kg).

3/16" hex wrench (C) and four 5/16-18 x 1/2" button head
cap screws (D).

WARNING:

MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT. Displays can weigh in
excess of 40 lbs (18.1kg). ALWAYS use two people and
proper lifting techniques when installing display.

WARNING:

MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT. Make sure mounting buttons
on display are properly seated in mounting holes in faceplate.

To install display:

1. While supporting both sides of display, align four mounting
buttons on display or interface bracket with four mounting
holes in faceplate. (See Figure 4)

2. Lower display into place listening for audible "click" to
ensure recessed area of mounting buttons are properly
seated in lower area of mounting holes and "click lock"
mechanism has engaged. (See Figure 4) and
(See Figure 5)

IMPROPER INSTALLATION CAN LEAD TO

IMPROPER INSTALLATION CAN LEAD TO

4

Figure 4

NOTE:

Figure 3

Holes are provided in the faceplate for use with a
padlock or similar locking device, if desired. In addition,
the pin and nut may be removed from the upper holes
and moved to the lower holes for use as a more
permanent locking device. (See Figure 5)

Installation Instructions PCM SERIES

2

1

A padlock or bolt may
be placed through latch holes

To use as a
more permanent
lock, remove pin
and nuts and move
to lower holes

3

1

2

3

1

2

3

1

2

Display Roll Adjustment

To adjust display roll:

1. Loosen 3/8-16 Nylock nut. (See Figure 7)

2. Adjust faceplate to desired position. (See Figure 7)

3. Tighten 3/8-16 Nylock nut. (See Figure 7)

Figure 5

Adjustments

The PCM is designed to accommodate 5" of display height
adjustment, 4º right and left display roll adjustment, and 15º
down/5º up display pitch (Tilt) adjustment.

Remove display before performing adjustments.

Display Height Adjustment

To adjust display height:

1. Loosen four 5/16-18 button head cap screws using 3/16"
hex wrench (C). (See Figure 6)

2. Adjust faceplate to desired position. (See Figure 6)

3. Tighten four 5/16-18 button head cap screws using 3/16"
hex wrench (C). (See Figure 6)

Figure 7

Display Pitch (Tilt) Adjustment

To adjust display pitch:

1. Loosen four 5/16-18 button head cap screws.
(See Figure 8)

2. Adjust to desired tilt position. (See Figure 8)

3. Tighten four 5/16-18 button head cap screws.
(See Figure 8)

Figure 6

Figure 8

5

PCM SERIES Installation Instructions

6

Installation Instructions PCM SERIES

7

PCM SERIES Installation Instructions

Chief® and ClickConnect™ are trademarks of Milestone AV Technologies, Inc. All rights reserved.

USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378

P 800.582.6480 / 952.894.6280
F 877.894.6918 / 952.894.6918

Chief Manufacturing, a division of
Milestone AV Technologies

8805-000114 RevE
©2008 Milestone AV Technologies

www.chiefmfg.com

04/08

Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands

P [phone]
F [phone]

Asia Pacific A Room 24F, Block D, Lily YinDu International Building

LuoGang, BuJi Town, Shenzhen, CHINA.

P [phone]
F [phone]