Page 1
INSTALLATION INSTRUCTIONS
SMALL FLAT PANEL STATIC WALL MOUNT
Model: FSR Series
Specifications:
• Designed for installation on single wood studs or
drywall (1/2" minimum thickness); either option
provides ±1/2" lateral shift.
• Weight capacity of 45 lbs (20 kg) for wood stud or
drywall installation.
BEFORE YOU BEGIN
WARNING: It is the installer’s responsibility to make sure all components are properly assembled and installed using
the instructions provided. Failure to read, thoroughly understand, and follow all instructions can result in serious
personal injury, damage to equipment, or voiding of factory warranty.
• If you have any questions about this these instructions or your specific installation, contact Chief Manufacturing
at 1-800-582-6480 or 952-894-6280.
CHIEF MANUFACTURING INC.
1-800-582-6480 952-894-6280 FAX 952-894-6918
8401 EAGLE CREEK PARKWAY, STE 700
SAVAGE, MINNESOTA 55378 USA
©2006 Chief Manufacturing
8804-000290
www.chiefmfg.com
01/06
Page 2
Model: FSR Series Installation Instructions
IMPORTANT WARNINGS AND CAUTIONS!
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: It is the installer’s responsibility to make sure the structure to which this unit is attached can support five
times the combined weight of all equipment. Reinforce the structure as required before installing the unit. Failure to
provide adequate structural strength for this unit can result in serious personal injury or damage to equipment!
WARNING: It is the installer’s responsibility to make sure the combined weight of the display, mount, accessories,
and any other attached equipment must not exceed 45 lbs (20 kg), the maximum support weight of this unit.
Exceeding the maximum support weight can result in serious personal injury or damage to equipment!
WARNING: Make sure the latches securing the display are fully closed at all times except when removing or
installing the display. The latches must be fully closed when installing or removing cables from the display.
DIMENSIONS
2
Page 3
Installation Instructions Model: FSR Series
TOOLS REQUIRED FOR INSTALLATION
• Drill
• 1/8" drill bit (wood stud installation)
• 3/8" drill bit (drywall installation)
• Hammer (drywall installation)
• Phillips screwdriver, #2
NOTE: Other tools may be required depending on your
method of installation.
PARTS
After unpacking carton, inspect and verify contents (See
Figure 1). If any listed parts are missing or damaged,
contact Chief Customer Service at 1-800-582-6480.
Table 1: Parts
Item Description Qty
10 PLATE, Wall 2
20 ANCHOR, Hollow Wall, #10-24 4
30 WASHER, Flat, Standard Machine Screw, #10 4
40 SCREW, Phillips Pan Head Sheet Metal,
#10 x 2-1/2"
2
(10)
Figure 1: Parts
(20)
(30)
(40)
3
Page 4
Model: FSR Series Installation Instructions
INSTALLATION
The FSR may be installed on either a single wood stud,
or drywall (1/2" minimum thickness).
INSTALL MOUNT TO SINGLE WOOD STUD
1. Determine approximate mounting location, keeping in
mind the display size.
2. Use a stud sensor to locate applicable wood stud.
Mark location with a pencil.
3. Level plate (10) at desired height and, using plate (10)
as a template, mark the location of upper and lower
pilot holes. Ensure marks are in the center of wood
stud.
NOTE: Mount can provide ±1/2" of lateral shift by using
mount holes on either side of vertical centerline.
WARNING: ELECTRICAL SHOCK HAZARD! Drilling
into electrical wires or cables can cause DEATH or
SERIOUS PERSONAL INJURY! ALWAYS make
certain area behind mounting surfaces is free of
electrical wires and cables before drilling or installing
mount fasteners.
4. Drill pilot holes using a 1/8" drill bit. Ensure pilot holes
are straight.
INSTALL MOUNT TO DRYWALL
WARNING: Drywall must be 1/2" minimum thickness.
Failure to provide adequate structural strength for this
unit can result in serious personal injury or damage to
equipment!
1. Determine approximate mounting location, keeping in
mind the display size.
2. Level plate (10) at desired height and, using plate (10)
as a template, mark the location of the four anchor
holes (one in each corner slot).
WARNING: ELECTRICAL SHOCK HAZARD! Drilling
into electrical wires or cables can cause DEATH or
SERIOUS PERSONAL INJURY! ALWAYS make
certain area behind mounting surfaces is free of
electrical wires and cables before drilling or installing
mount fasteners.
3. Drill anchor holes using a 3/8" drill bit. Ensure holes
are straight and completely through drywall.
4. Insert anchor (20) into anchor hole and seat with
gentle tapping from hammer. Anchor barbs should be
fully engaged in drywall (See Figure 3).
5. Using Phillips screwdriver, insert screw (40) through
washer (30), plate (10), and drywall (not shown) and
install into pilot holes (See Figure 2).
Pilot
Holes
(2 places)
Wood
Stud
Figure 2: Installation to Single Wood Stud
6. Repeat for remaining screw (40).
7. Tighten both screws (40) securely.
(30)
(2 places)
(40)
(2 places)
(10)
Drywall
Anchor barb
Not collapsed
Figure 3: Drywall Anchor
5. Using Phillips screwdriver, tighten anchor screw until
anchor has fully collapsed against back side of
drywall.
NOTE: Anchor screw will feel tight until anchor begins to
collapse. Screw will then turn easier for many
turns. Screw will feel tight when anchor has fully
collapsed.
6. Repeat steps 4. and 5. for remaining anchors.
7. Remove and retain anchor screws from anchors (20).
NOTE: Anchors (20) may come with small washers which
may be left on the screw or discarded. These
small washers do NOT replace washers (30).
Collapsed
8. Using Phillips screwdriver, insert anchor screws
through washers (30) and plate (10) and install into
4
Page 5
Installation Instructions Model: FSR Series
collapsed anchors (20). Tighten until secure (See
Figure 4).
Button location for
(20)
(4 places)
(30)
(4 places)
Anchor Screw
(4 places)
100mm x 100mm
pattern (4 places)
Button location for
75mm x 75mm
pattern (4 places)
(10)
Figure 4: Installation to Drywall
INSTALL DISPLAY TO MOUNT
NOTE: Proper interface must be attached to display. See
instructions that come with interface assembly.
1. Open latching flag by rotating flag clockwise on plate
(10) (See Figure 5).
Latching
Flag
(10)
NOTE: Display not shown for clarity.
Figure 6: Install Display to Plate
3. Close latching flag by rotating flag counterclockwise
on plate (10) (See Figure 7).
NOTE: An optional padlock may be used to secure
latching flag.
Latching
Flag
(10)
NOTE: Display not shown for clarity.
Figure 7: Close Latching Flag
4. Connect cables to display as required.
Figure 5: Open Latching Flag
2. Lift and maneuver display such that all buttons fit into
button openings on plate (10). Lower display firmly
into place. Ensure each button has fully seated in its
button opening (See Figure 6).
NOTE: Mounting buttons are shown in the 100mm x
100mm pattern. Plate (10) will also accomodate
a 75mm x 75mm pattern.
REMOVE DISPLAY FROM MOUNT
1. Disconnect all cables from display.
2. Open latching flag by rotating flag clockwise on plate
(10) (See Figure 5).
3. Lift and maneuver display mounting buttons out of
button openings.
5
Page 6
Model: FSR Series Installation Instructions
6
Loading...