Page 1
INSTALLATION INSTRUCTIONS
Vertical / Horizontal Universal Projector Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
VPAU
Page 2
VPAU Installation Instructions
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to mounting system does not
exceed 75 lbs (34.0 kg).
• The weight capacity of the VPAU may be LIMITED to
the lowest weight capacity of any other accessory used
within the mounting system.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this mounting system outdoors.
IMPORTANT ! : The VPAU mounts are designed to be
mounted to a 1-1/2" NPT or NPSM following ANSI/ASME
B1.20.1 (Schedule 40, 0.154" minimum thickness steel or
aluminum - ASTM B221) threaded extension column (not
included).
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all mounting systems
are properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this mounting system can result in serious personal injury
or damage to equipment! It is the installer’s responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. Reinforce the structure as required before
installing the mounting system.
--SAVE THESE INSTRUCTIONS--
2
Page 3
Installation Instructions VPAU
100°
100°
95°
95°
LARGER RANGE OF
RO T AT ION C AN BE ACHIEV ED
BY ADDING ADDITI ONAL BOLT I N
SEPARATE HOLE THEN REMOVING CU RRENT BOLT
1 1/2" NPT THREAD
MOUNT HAS 190 RANGEOF
MOTION FROM EACH
BOLTINGPOIN T
6.42
163.1
0.90
23.0
15.75
400.1
15.00
381.0
RANGE OF REACH
421.7
16.60
0.25
6.4
DIMENSIONS: INCH
[MILLIMETER]
DIMENSIONS
3
Page 4
VPAU Installation Instructions
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
LEGEND
4
Page 5
Installation Instructions VPAU
#2
3/16"
[included]
7/16"
A (1)
[VPAU]
B (1)
[Interface bracket]
C (2)
[Slide protection
plate]
D (2)
5/16-18 x 1/4"
E (1)
3/16"
G (2)
1/4-20 x 1/2"
H (2)
F (2)
[Bracket leg]
J (4)
[Thumb nut]
K (6)
M3 x 20mm
L (6)
M4 x 20mm
M (6)
M5 x 20mm
N (6)
M6 x 20mm
P (6)
M6 x 12mm
Q (6)
M5 x 12mm
R (6)
M6
S (6)
M3 x 10mm
T (6)
M4 x 10mm
U (6)
M2.5 x 10mm
V (6)
M4
VPAU Mounting Hardware Kit
1/4"
W (1)
5/16-18 x 1"
X (1)
5/16"
NOTE:
The M2.5, M3 and M4 Phillips screws are used with the M4 flat washers (V).
NOTE:
The M5 and M6 Phillips screws are used with the M6 flat washers (R).
TOOLS REQUIRED FOR INSTALLATION
PARTS
5
Page 6
VPAU Installation Instructions
3
(A)
Threaded extension
column (not included)
x 2
1
2
(Example projector
with 3 mounting holes)
1
2
(B)
PREPARATION
Locate Mounting Site
WARNING: IMPROPER INSTALLATION MAY LEAD TO
PROJECTOR MOUNT FALLING CAUSING SEVERE
PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is
the installers responsibility to make certain the structure to
which the projector mount is bei n g mo un ted is capable of
supporting five times the weight of the projector mount and all
attached equipment. Reinforce the structure as required
before installing the projector mount.
1. Determine required position of the VPAU projector mount.
2. Determine required distance of the VPAU from the screen
using the lens-to-screen distance information included with
the projector.
INSTALLATION
Installing to 1-1/2" Threaded Extension Column
1. Install 1-1/2" NPT or NPSM following ANSI/ASME B1.20.1
(Schedule 40, 0.154" minimum thickness steel or aluminum
- ASTM B221) threaded extension column (not included)
into threaded collar (not included) until tight, with a minimum
of four threads engaged.
2. Thread VPAU projector mount (A) onto the threaded
extension column (not included) until hand tight, with a
minimum of four threads engaged.
3. Secure VPAU to pipe by installing and tightening one or
two 5/16-18 x 1/4" set screws (D) until tight. (See Figure 1)
Attaching Interface to Projector
1. Determine the distance between the mounting holes on the
projector. (See Figure 2)
NOTE: There is not a standard mounting hole configuration
pattern for projectors.The interface legs can be
configured to match the mounting holes on the
projector.
Figure 2
2. Loosen, but do NOT remove, the screws holding the legs to
the interface bracket (B). (See Figure )
CAUTION: DO NOT OVERTIGHTEN! Over tightening of
set screw can damage threads on pipe.
Figure 3
Figure 1
6
Page 7
Installation Instructions VPAU
x 1
Remove one
leg if the
projector has three
mounting holes.
Legs may be
attached through
horizontal slot
x 1
(G)
(F)
(H)
Additional bracket
legs may be attached
if there are more than
four mounting holes
Attaching
through interface
feet
Attaching directly
through interface leg
NOTE:
NOTE:
Remove one Phillips screw, hex nut and leg if the
projector only has three mounting holes. (See Figure 4)
Add additional bracket leg(s) (F) (using one 1/4-20 x 1/2"
Phillips head cap screw (G) and one square nut (H) per
bracket leg) if projector has more than four mounting
holes. (See Figure 4)
NOTE: The interface legs may be adjusted into numerous
configurations. The interface legs may be extended out
or brought into the center of the interface.
NOTE: If it is not possible to align the adjustable legs with the
mounting hole pattern on the projector, a leg or legs
may be moved and/or removed so that the interface
bracket may be aligned using a horizontal slot. (See
Figure 4)
IMPORTANT ! : At a minimum, three interface bracket
legs MUST be attached to the projector.
3. Place the interface bracket on the projector.
4. Adjust legs on interface as needed to align the legs with
projector mounting holes.
5. Secure interface bracket (B) to the projector by selecting the
screws (K-U) and flat washers (R or V) that fit the mounting
holes in the projector.
NOTE:
6. Attach the universal interface to the projector either through
The M2.5, M3 and M4 Phillips screws are used with the
M4 flat washers (V). The M5 and M6 Phillips screws are
used with the M6 flat washers (R).
the bracket feet, or directly through the legs. (See Figure 5)
Figure 5
7. Do NOT tighten screws at this time.
Figure 4
7
Page 8
VPAU Installation Instructions
Remove foot and
reattach with slot
on bottom
1
(J) x 4
(B)
3
Back of
mounting
slot
(A)
(B)
(J)
4
Adjusting Interface Bracket Feet
WARNING: IMPROPER INSTALLATION CAN LEAD TO
PROJECTOR FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! DO NOT substitute
hardware. Use only hardware provided by the manufacturer
and make certain all hardware is properly tightened.
1. Adjust the feet on the interface to the proper height.
NOTE: Foot height is adjusted for a variety of reasons
2. Visually check the height of the mounting plate on the
3. Loosen screw and adjust foot that is attached to adjustable
4. Adjust foot height as needed. If necessary, use a level to
5. Tighten screw .
6. Repeat procedure for each foot as needed until the feet on
including: ventilation, uneven projector surface, or to
level the interface bracket mountin g pla t e.
interface.
leg. The foot may be removed and reattached to allow more
adjustment, if necessary. (See Figure 6)
verify that the interface mounting plate is level.
the interface are adjusted properly.
Figure 7
2. Orient projector with attached interface bracket (B) with
VPAU (A). (See Figure 8)
3. Lift projector so that screws with thumb nuts (J) are aligned
with mounting slots in projector mount.
4. Slide projector with interface bracket into mounting slots in
VPAU until screws are seated against the back of mounting
slots.
Figure 6
Install Projector
WARNING: IMPROPER INSTALLATION CAN LEAD TO
PROJECTOR FALLING RESULTING IN SERIOUS
PERSONAL INJURY OR DAMAGE TO EQUIPMENT. DO
NOT substitute hardware. Use only the hardware provided by
the manufacturer.
1. Install four thumb nuts (J) onto screw at each corner of
interface bracket (B). Do not tighten completely. (See
Figure 7)
WARNING: IMPROPER INSTALLATION CAN LEAD TO
PROJECTOR FALLING RESULTING IN SERIOUS
PERSONAL INJURY OR DAMAGE TO EQUIPMENT. Make
certain mounting slots in VP AU slide under thumb screws and
that screws are seated in the back of slots.
8
Figure 8
Page 9
Installation Instructions VPAU
5
5
(C)
Shorter tabs
1 3
2
4
6
5
5
5. Add two slide protection brackets (C), to the two VPAU
sides which have shorter tabs. (See Figure 9)
Figure 10
Figure 9
6. Secure projector to mount (See Figure 9) by completely
tightening four thumb nuts.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
PROJECTOR FALLING RESULTING IN SERIOUS
PERSONAL INJURY OR DAMAGE TO EQUIPMENT. Slide
protection brackets (C) MUST be in place before making
adjustments to VPAU and projector.
NOTE: It is normal for the slide protection brackets (C) to be
slightly loose to the touch when installed properly.
ADJUSTMENTS
CAUTION: Be sure to check instructions included with
projector to see if that projector model can be rotated and
adjusted from vertical to horizontal without causing damage
to the projector.
YAW Adjustment
1. Loosen two yaw adjustment set screws. (See Figure 10)
NOTE: Yaw is only adjustable when attached to a threaded
pipe.
Pitch/Roll Adjustment
CAUTION: Be sure to check instructions included with
projector to see if that projector model can be rotated and
adjusted from vertical to horizontal without causing damage
to the projector.
4. Loosen pitch/roll adjustment button head screws (two on
each end of the VPAU projector mount).
5. Adjust projector angle to desired pitch. (See Figure 11)
6. Tighten pitch/roll adjustment button head screws (two on
each end of the VPAU projector mount).
WARNING: Do not turn the projector to the end of the pipe
threads. The projector, interface bracket and VPAU will fall
from the pipe if it is unthreaded too far! A minimum of four
threads MUST be engaged in order to ensure a secure
connection!
2. Adjust projector by turning the projector on the column to
the desired yaw position.
3. Tighten two yaw adjustment locking screws. (See Figure 10)
Figure 11
9
Page 10
VPAU Installation Instructions
10
8
9
x 1
(W)
7
11
Rotation Adjustment
7. Slightly loosen the button head screw on base of VPAU.
8. Rotate the projector on the VPAU as required. There is
180+° rotation adjustment possible.
If additional rotation is required:
9. Add one 5/16-18 x 1" button head cap screw (W) along with
one 5/16" washer (X) into one of the two sep a rate holes in
the VPAU base. (See Figure 12)
10. Remove the existing button head cap screw and washer
from VPAU base.
11. Adjust rotation as required.
12. TIghten button head cap screw after rotation is complete.
Figure 12
10
Page 11
Installation Instructions VPAU
11
Page 12
VPAU Installation Instructions
Chief, a products division of
Milestone AV Technologies
8800-002846 Rev00
2016 Milestone AV Technologies
www.milestone.com
06/16
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000
F 877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852
F +31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
Loading...