CHIEF SSB-2100, SSM-2100, SLB-2100, SLM-2100 Installation Instructions Manual

INSTALLATION INSTRUCTIONS

SLM-2100

s

a

ree

n

circled

)

are

encir

c

led

)

Towards front of

SSB-2100, SSM-2100, SLB-2100 and SLM-2100 Interface Brackets

SSB-2100, SSM-2100, SLB-2100 and SLM-2100 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the
specific installation instructions provided with the mount for additional installation information.

Unpack carton and verify kit contents. If any listed parts are missin g, immediately contact a Chief Customer Service representative.

WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!

(1) Interface Bracket (3) M4 -12mm Flat Head Screw
(3) 10 - 24 Thumb Nuts** (3) 1/2" x .218 x 1/4" Nylon Spacer
(1) All-Points Security Kit

projectorTowards front of

terface

brack

et con

nectio

n

(No

te: SSB

-style

SLB-2100

ace bra

interf

projector

cket c

onnec

tions

(Note:

SSM-

style in

**Only used when installing SLB/SSB interface brackets.

NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the

encircled locati ons abov e. DO NOT attempt t o subst itute a nd USE ONLY thi s pre-in stalled hardware for SSB-sty le and SSM-st yle
interface bracket installation.

Installation Instructions

WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface bracket.

NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.

1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time

2. Turn projector upside down.

3. Place the three 1/4” nylon spacers over the three threaded inserts in the bottom of the projector.

4. Place the interface bracket onto the three 1/4” nylon spacers on the bottom of the projector.

5. Align the three mounting holes in the bracket with the three nylon spacers.

6. Using the three M4 x 12mm screws, secure interface bracket to projector and tighten all fasteners at this time.

.

NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation

instructions in the All-Points Security Kit.

Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.

Milestone AV Technologies, and its affiliated co rpo rat ions a nd s ubs id iaries (collectively, "Milestone"), intend to mak e th is ma nual ac curate and complete. However, Milestone mak es

no claim that the information contained h erein co vers all details, conditions or variations, nor does it provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief Manufacturing, a products division of Milestone AV Technologies

• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918

8401 Eagle Creek Parkway, Savage, MN 55378

©2009 Milest one AV Techn ologies,

a Duchossois Gr oup Company

8850-0 00 14 3 R ev 01

05/09