CHIEF SSB-202, SSM-202, SLM-202, SLB-202 Installation Instructions Manual
INSTALLATION INSTRUCTIONS
(
a
r
een
c
ircle
d
)
c
k
e
t
c
o
n
n
e
c
tio
n
s
a
r
e
e
Towards front of
Towards front of
SSB-202, SSM-202, SLB-202 and SLM-202 Interface Brackets
SSB-202, SSM-202, SLB-202 and SLM-202 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing , immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
(1) Interface Bracket (4) Washer, M4
(4) 10-24 Thum b Nuts ** (4) Screw, Pan head, M4 x 10mm
(1) All-Points Security Kit
projector
projector
SLB-202 SLM-202
tions
nnec
et co
rack
face b
inter
-style
SSB
Note:
**Only used when installing SLB/SSB interface brackets.
(Note:
SSM-style
ircled
nc
inter
)
bra
face
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encircled locati ons abov e. DO NOT attempt t o subst itute a nd USE ONLY thi s pre-in stalled hardware for SSB-sty le and SSM-st yle
interface bracket installation.
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place the inte rface b racket ont o the bot tom of the p rojec tor and align the hol es in the br acket wit h the t hreaded inse rts i n the bot tom of the
projector.
4. Using the M4 x 10mm mounting screws and washers and position screws with washers into the mounting holes. Tighten all fasteners at
this time, securing the bracket to the projector.
NOTE: Security sc rews can be sub stit uted when mount i ng interfa ce br acket to proj ec tor by using t he parts and inst allat ion in structi ons in th e
All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
Milestone AV Technologies, and its affiliated co rpo rat ions a nd s ubs id iaries (collectively, "Milestone"), intend to mak e th is ma nual ac curate and complete. However, Milestone mak es
no claim that the information contained h erein co vers all details, conditions or variations, nor does it provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8401 Eagle Creek Parkway, Savage, MN 55378
©2009 Milest one AV Techn ologies,
a Duchossois Gr oup Company
8802-0 00 26 9 R ev 01
05/09
Loading...