Chief SLB191 Installation Guide
INSTALLATION INSTRUCTIONS
(
N
ote
:
S
S
M
-st
y
l
e
int
e
rfa
ceb
r
a
cke
tco
nne
c
t
ion
s
a
reenc
ircled)
(
c
e
b
rac
ket
con
n
e
cti
o
n
s
are
encircl
e
d
)
Towards front of
Towards front of
SSB-191, SSM-191, SLB-191 and SLM-191 Interface Brackets
SSB-191, SSM-191, SLB-191 and SLM-191 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing , immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
(1) Interface Bracket (2) Screw, Phillips pan head, M4 x 20mm
(4) 10-24 Thum b Nuts ** (2) Screw, Phillips flat head, M4 x 20mm
(1) All-Points Security Kit (4) Spacer, Nylon, 1/2" x .194 x 1/2"
(2) Washer, Flat, M4
projector
: SSB-
Note
SLB-191 SLM-191
terfa
style in
projector
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encircled locati ons abov e. DO NOT attempt t o subst itute a nd USE ONLY thi s pre-in stalled hardware for SSB-sty le and SSM-st yle
interface bracket installation.
Installation Instructions
WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place 1/2" nylon spacers over the threaded inserts in the bottom of the projector.
4. Place the i nterface br acke t ont o the 1/2" nylon spacer s on th e bottom of the project or a nd ali gn t he mo unting ho les i n the brack et wi th t he
nylon spacers.
5. Using the M4 x 20mm pan head screws and M4 washers, posi tion screws with washers into the side holes and position the M4 flat head
screws in the counter sink holes. Tighten all fasteners at this time, securing the bracket to the projector.
NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation
instructions in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
Milestone AV Technologies, and its affiliated co rpo rat ions a nd s ubs id iaries (collectively, "Milestone"), intend to mak e th is ma nual ac curate and complete. However, Milestone mak es
no claim that the information contained h erein co vers all details, conditions or variations, nor does it provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
©2009 Milest one AV Techn ologies,
a Duchossois Gr oup Company
8802-0 00 26 0 R ev 01
05/09
Loading...