CHIEF RLT2, RXT2 Chief RLT2_1.pdf

Page 1
INSTALLATION INSTRUCTIONS
Instrucciones de instalación Installationsanleitung Instruções de Instalação
Istruzioni di installazione Installatie-instructies Instructions d´installation
Universal Tilt Mounts
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
RMT2/RLT2/RXT2
Page 2
RMT2/RLT2/RXT2 Installation Instructions
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! : The RMT2/RLT2/RXT2 mounts are
to be mounted to an 8" concrete, 8"x8"x16" concrete block, or 2" x 4" wood studs.
designed
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. The wall to which the mount is being attached may have a maximum drywall thickness of 5/8" (1.6cm). Do not install drywall anchors into the seam between drywall pieces.
--SAVE THESE INSTRUCTIONS--
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components attached does not exceed 125 lbs (56.7 kg) for the RMT2 and RLT2 or 175 lbs (79.4 kg) for the RXT2. Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury.
2
Page 3
Installation Instructions RMT2/RLT2/RXT2
15.75
MAX
19.94
7.87
TOP MOUNTING
HOLE TO CENTERLINE
NOTCH ON WALL PLATE
7.00
WALL
OPENING
2.50 CENTERLINE TO BOTTOM OF WALL PLATE OPENING
22.00
.34
1.00
8.38
11.00
16.00
5.19
11.49
1.96
- TILTS BACK 5.4°
-CABLE ACCESS WHEN KICKSTAND IS ACTIVATED
12°
MAX TILT
15.75
MAX
28.69
7.87
TOP MOUNTING
HOLE TO CENTERLINE
NOTCH ON WALL PLATE
7.00
WALL
OPENING
30.75
.34
1.00
8.38
15.38
16.00
5.19
24.00
2.50 CENTERLINE TO BOTTOM OF WALL PLATE OPENING
11.49
1.96
- TILTS BACK 5°
-CABLE ACCESS WHEN KICKSTAND
12°
DIMENSIONS-RMT2
DIMENSIONS-RLT2
3
Page 4
RMT2/RLT2/RXT2 Installation Instructions
7.00
WALL
OPENING
38.00
1.00
8.38
.34
MAX
35.94
19.00
16.00
5.19
24.00
32.00
9.84
TOP MOUNTING
HOLE TO CENTERLINE
NOTCH ON WALL PLATE
11.49
2.50 CENTERLINE TO BOTTOM OF WALL PLATE OPENING
1.96
- TILTS BACK 5°
-CABLE ACCESS WHEN KICKSTAND
12°
DIMENSIONS-RXT2
4
Page 5
Installation Instructions RMT2/RLT2/RXT2
Tighten Fastener
Apretar elemento de fijación Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación Befestigungsteil lösen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca Gabelschlüssel Chave de bocas Chiave a punte aperte Steeksleutel Clé à fourche
By Hand
A mano Von Hand Com a mão A mano Met de hand À la main
Hex-Head Wrench
Llave de cabeza hexagonal Sechskantschlüssel Chave de cabeça sextavada Chiave esagonale Zeskantsleutel Clé à tête hexagonale
Pencil Mark
Marcar con lápiz Stiftmarkierung Marcar com lápis Segno a matita Potloodmerkteken Marquage au crayon
Drill Hole
Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou
Adjust
Ajustar Einstellen Ajustar Regolare Afstellen Ajuster
Remove
Quitar Entfernen Remover Rimuovere Verwijderen Retirez
Optional
Opcional Optional Opcional Opzionale Optie En option
Security Wrench
Llave de seguridad Sicherheitsschlüssel Chave de segurança Chiave di sicurezza Veiligheidssleutel Clé de sécurité
LEGEND
5
Page 6
RMT2/RLT2/RXT2 Installation Instructions
7/32" (5.5mm) #2
1/2" (12.7mm)
5/16" (7.9mm)
GC(6)
M4 x 25mm
GG(6)
M5 x25mm
GK(6)
M6 x 35mm
GN(6)
M8 x 40mm
1/2"(12.7mm)
A(1)
[wall plate]
B(1)
[left upright]
GA(8)
M4 x 16mm
GB(6)
M4 x 20mm
GD(6)
M4 x 35mm
GE(6)
M5 x16mm
GF(6)
M5 x20mm
GI(6)
M6 x16mm
GJ(6)
M6 x 25mm
GL(6)
M8 x 20mm
GM(6)
M8 x 30mm
GO(6)
M8 x 50mm
GP(8)
1/4"(6.4mm)
GQ(8)
GS(8)
[universal washer]
D(4 or 6)
5/16 x 2 1/2"
E(4 or 6)
5/16"
F(4 or 6)
[concrete anchor]
C(1)
[right upright]
For below kit, quantities are 4 for RMT2 and RLT2, 6 for RXT2.
(RXT2 shown)
GH(6)
M5 x 35mm
G(1)
Hardware Bag
TOOLS REQUIRED FOR INSTALLATION
PARTS
6
Page 7
Installation Instructions RMT2/RLT2/RXT2
1
1
(A)
2
3
x 4 or 6
CENTER
LINE
3 x 16"
2 x 24"
2 x 16"
(D) x 4 or 6
4
(E) x 4 or 6
(A)
Assembly And Installation
Install Wall Plate to Wall - Wood Studs
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. The wall to which the mount is being attached may have a maximum drywall thickness of 5/8" (1.6cm). Do not install drywall anchors into the seam between drywall pieces.
1. Unfold wall plate (A) to prepare it for mounting to wall. (See Figure 1)
Figure 2
Figure 1
2. Level wall plate (A) and mark locations of pilot holes. (See Figure 2)
NOTE: The RMT2 must be installed on two 16" studs. The
RLT2 can be installed on 16" studs (inner holes) or 24" studs (outer holes). For the RXT2, it can be mounted over two or three 16" studs or two 24" studs. If mounting to three 16" studs, it must be mounted to all three studs using the outer holes and center holes. (See Figure 3) All studs must be 2"x4".
NOTE: The vertical center of the wall plate is labeled as the
center directly below each hinge. Keep this in mind when determining mounting location. (See Figure 3)
3. Drill 7/32" (5.5mm) diameter pilot holes into wood studs at marked locations. (See Figure 2)
Figure 3
4. Install 5/16 x 2 1/2" hex head cap screws (D) through four flat washers (E), wall plate (A) and into wood studs. (See Figure 4)
Figure 4
7
Page 8
RMT2/RLT2/RXT2 Installation Instructions
CENTER
LINE
2
3
x 4 or 6
Anchor flush with concrete wall
Anchor (F)
wall covering
(A)
Pilot Hole ­5/16 x 3 1/4"
(M8 x 82.5mm)
(D)
(E)
concrete wall
(A)
(E) x 4 or 6
(F) x 4 or 6
5
(D) x 4 or 6
4
Install Wall Plate to Wall - Concrete or Concrete Block
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. The wall to which the mount is being attached may have a maximum drywall thickness of 5/8" (1.6cm).
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL CORDS OR CABLES CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surface is free of electrical wires and cables before drilling or installing fasteners.
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surface is free of gas, water, waste, or any other plumbing before cutting, drilling, or installing fasteners.
1. Unfold wall plate (A) to prepare it for mounting to wall. (See
2. Level wall plate (A) and mark locations of pilot holes at
IMPORTANT ! : The RMT2-RLT2-RXT2 mounts are designed to be mounted to an 8" concrete or 8"x8"x16" concrete block wall.
NOTE:
NOTE: For the RXT2, use the outer four holes and the two
NOTE: The vertical center of the display will be even with the
Figure 1)
desired mounting location. (See Figure 5)
For the RLT2, either the inner or outer four holes may be used.
middle holes on wall plate for installation.
center line indicated on the labels located directly below each hinge. Keep this in mind when determining mounting location. (See Figure 5)
3. Drill 5/16" (8mm) diameter pilot holes into wall at marked locations. Holes must be drilled at least 3 1/4 inches deep. (See Figure 5)
4. Install four or six concrete anchors (F) into drilled holes. Use a hammer to tap anchors into holes. (See Figures 6 and 7)
IMPORTANT ! : The anchors must be installed through any wall covering until flush with the concrete wall. (See Figure 6)
Figure 6
5. Using 1/2" (12.7mm) wrench, install screws (D) through flat washers (E), wall plate (A) and into concrete anchors (F). (See Figure 7)
8
Figure 5
Figure 7
Page 9
Installation Instructions RMT2/RLT2/RXT2
(non-recessed holes)
(recessed holes)
6
(GA-GO) x4,x6,x8
(GS) x4,x6,x8
2
4
5
7
(GA-GO) x4,x6,x8
2
4
5
(GS) x4,x6,x8
(GP or GQ)
3
7
(C)
(B)
(C)
6
(B)
NOTE: Use universal washer (GS) ONLY with M4, M5 and M6 screws.
NOTE: Use universal washer (GS) ONLY with M4, M5 and M6 screws.
Install Brackets to Display
WARNING: The minimum hole pattern size is 100mm x
100mm for the RMT2 and RLT2 and 200mm x 200mm for the RXT2.
1. Lay display face down on protective surface.
CAUTION: Using screws of improper diameter may
damage your display! Proper screws will easily thread into display mounting holes.
2. Select screw diameter by examining hardware (GA-GO) (8mm, 6mm, 5mm, or 4mm) and comparing with mounting holes on display. (See Figure 8)
3. Select spacers: (See Figure 8)
If mounting holes are not recessed and both
brackets (B or C) can lay flat against display, then
IMPORTANT ! : The M8 screws do NOT require a washer. Use the universal washer (GS) ONLY with M4, M5 and M6 screws.
4. Select screw length: (See Figure 8)
5. Place brackets (B and C) on display, ensuring: (See
6. If installing display with wide hole pattern, it may be
no spacers are required.
If mounting holes are recessed, or if protrusions
prevent brackets (B or C) from laying flat, then spacers (GP or GQ) must be used. Select shortest spacer which will provide adequate fill. All spacers must be same length.
CAUTION: Using screws of improper length may damage
your display! Proper screws will have adequate thread engagement without contacting bottom of display mounting holes.
Using your hand, insert SHORTEST length screw
of selected diameter (GA, GE, GI or GL) through bracket (B or C), universal washer (GS, if required), selected spacer (GP or GQ, if required), into display mounting hole. Do NOT thread screw into hole at this time.
Proper screw length requires base of screw head
to protrude above flat washer a distance equal to or greater than the screw diameter. If screw length is inadequate, select longer screw. Select shortest screw which will protrude the required distance.
Figure 8)
Upper hooks are towards top of display.
Center of brackets (B and C) are as close to the
center of the back of display as possible after being installed. Center of bracket is indicated by the diamond-shaped hole.
necessary to swap the uprights (B and C). See Switching Interface Brackets section for details.
7. Using Phillips screwdriver, carefully install selected screws through universal washers (GS, if required), brackets (B and C), and spacers (GP or GQ, if required), into display. (See Figure 8)
8. Tighten all screws. Ensure all applicable display mounting holes (4, 6, or 8) are used.
Figure 8
9
Page 10
RMT2/RLT2/RXT2 Installation Instructions
center tab
of center tab
5
interface brackets must be hung on opposite sides
4
2
kickstand engaged
1
kickstand against wall
3
6
(Views from left side)
Install Display to Wall Plate
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components attached does not exceed 125 lbs (56.7 kg) for the RMT2 and RLT2 or 175 lbs (79.4 kg) for the RXT2. Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury.
WARNING: Display may be very heavy! Ensure display
can be safely lifted and maneuvered as required to install on wall plate. Failure to take adequate precautions can result in serious personal injury or damage to equipment!
WARNING: Interface brackets must be hung on opposite
sides of the center tab on wall plate! (See Figure 9)
1. Make sure interface brackets are in the kickstand position by
2. Hang display with brackets (B and C) on upper rail of wall
Figure 9
pulling down on handles as far as possible. (See Figure 10)
plate (A). Kickstand should be engaged with lower portion of wall plate. (See Figure 10)
Figure 10
NOTE:
3. Unlock kickstand by pushing up on interface brackets until
4. Push up on the interface brackets further in order to lock
5. Straps can be tucked behind display on notch on interface
6. (Optional) Route padlock or cable lock (not included)
Any cable management or rear display adjustments should be made when the display is resting on the kickstand.
kickstand rests against the wall. (See Figure 10)
display into position against wall. (See Figure 10)
brackets (B and C) after installation is complete so that they will not be visible to the viewer. (See Figure 9)
through bottom holes on interface bracket to provide additional security. (See Figure 10)
10
Page 11
Installation Instructions RMT2/RLT2/RXT2
1
2
2
1 3
tilt tension adjustment
knob
Switching Interface Brackets (Optional)
For wide hole patterns, interface brackets must be reversed. See Table below to determine if this is necessary.
Table 1: Hole Pattern Width
Model #
RMT2 100-440mm 441-506mm RLT2 100-663mm 664-728.8mm RXT2 200-847mm 848-913mm
1. Remove the tilt tension knob, washer and screw from interface bracket. (See Figure 11)
IMPORTANT ! : Hold the brackets steady when removing the knob, washer and screw from interface bracket to prevent internal washers from falling out. If internal washers do fall out, they must be reinserted in proper position before reinstalling knob on the other side!
2. Replace the knob, washer and screw in the opposite order. (See Figure 11)
normal installation swap uprights
Tilt Adjustment
1. Adjust tilt tension adjustment knobs to desired tension. (See Figure 12)
2. Adjust tilt of display by pulling the top of display away from the wall until desired tilt position is reached. (See Figure 12)
3. Tighten tilt tension adjustment knobs to secure tilt position. (See Figure 12)
Figure 11
3. Repeat for the other interface bracket.
4. Install interface brackets according to instructions in Install Brackets to Display section.
Figure 12
11
Page 12
RMT2/RLT2/RXT2 Installation Instructions
Chief, a products division of Milestone AV Technologies
8800-002428 Rev01 2016 Milestone AV Technologies
www.chiefmfg.com
01/16
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000 F 877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852 F +31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099 F 852 2145 4477
Loading...