How it Works
Chief
Loading...
MFM6000B
Installation Guide
12 pgs928.16 Kb0

Chief MFM6000B Installation Guide

Download
INSTALLATION INSTRUCTIONS
Confidence Carts
MFM, PFM, MFQ, PFQ
MFM, PFM, MFQ, PFQ Installation Instructions
DISCLAIMER
WARNING:
follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided.
WARNING:
for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component.
Failure to read, thoroughly understand, and
Failure to provide adequate structural strength
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING:
serious injury or death if you do not follow the instructions.
CAUTION:
damage or destruction of equipment if you do not follow the corresponding instructions.
A WARNING alerts you to the possibility of
A CAUTION alerts you to the possibility of
WARNING:
serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components on the cart does not exceed 125 lbs (56.70 kg) for the MFM and MFQ, and 200 lbs (90.72 kg) for the PFM and PFQ.
Exceeding the weight capacity can result in
2
Installation Instructions MFM, PFM, MFQ, PFQ
[918] 36-1/8”
[640] 25-1/4”
[755] 29-3/4”
[100] 4”
[253] 10”
[1146] 45-1/8”
[39] 1-1/2”
[65] 2-1/2”
[955]
37-5/8”
[177]
[157] 6-1/4”
[1455]
57-1/4”
[810]
31-7/8”
[1261]
49-5/8”
15°
45°
NOTE: CUSTOM INTERFACE BRACKET
NOT SHOWN. THE CUSTOM INTERFACE
BRACKET NEEDED FOR YOUR DISPLAY
WILL ADD BETWEEN ½”AND 2” IN DEPTH AND MAY AFFECT LOCATION OF DISPLAY
ON THE MOUNT. SEE PSBU DRAWING ALSO.
WEIGHT CAPACITY: 200 LBS
HEIGHT ADJUSTMENT: 37-5/8” TO 49-5/8” IN 2” INCREMENTS
(GROUND TO MIDDLE OF SCREEN) TILT/ROLL/YAW: +15° TO +45°/ 0°/ + 0°
ALL MEASUREMENTS IN: [MILLIMETERS]
INCHES
+
PFM
[918] 36-1/8”
[640] 25-1/4”
[755] 29-3/4”
[100] 4”
[254] 10”
[1088] 42-7/8”
[157] 6-1/4”
[39] 1-1/2”
[65] 2-1/2”
[177] 7”
[955]
37-5/8”
[1393]
54-7/8”
[810]
31-7/8”
[1259]
49-5/8”
15°
45°
NOTE: CUSTOM INTERFACE BRACKET
NOT SHOWN. THE CUSTOM INTERFACE
BRACKET NEEDED FOR YOUR DISPLAY
WILL ADD BET WEE N ½” AND 2” IN DEPTH AND MAY A FFECT LOCATION OF DISPLAY ON THE MOUNT. SEE PSBU DRAWING ALSO.
WEIGHT CAPACITY: 125 LBS
HEIGHT ADJUSTMENT: 37-5/8” TO 49-5/8” IN 2” INCREMENTS
(GROUND TO MIDDLE OF SCREEN) TILT/ROLL/YAW: +15° TO +45°/ 0°/ 0°
ALL MEASUREMENTS IN: [MILLIMETERS]
INCHES
++
MFM
DIMENSIONS
3
MFM, PFM, MFQ, PFQ Installation Instructions
[918] 36-1/8”
[640] 25-1/4”
[755] 29-3/4”
[100] 4”
[254] 10”
[637] 25-1/8”
[157] 6-1/4”
[177] 7”
[511]
20-1/8”
[688]
27-1/8”
[365]
14-3/8”
[563]
22-1/8”
15°
45°
NOTE: CUSTOM INTERFACE BRACKET
NOT SHOWN. THE CUSTOM INTERFACE
BRACKET NEEDED FOR YOUR DISPLAY
WILL ADD BETWEEN ½”AND 2” IN DEPTH
AND MAY AFFECT LOCATION OF DISPLAY
ON THE MOUNT. SEE PSBU DRAWING ALSO.
WEIGHT CAPACITY: 125 LBS
HEIGHT ADJUSTMENT: 20-1/8” TO 22-1/8” IN 2” INCREMENTS
(GROUND TO MIDDLE OF SCREEN) TILT/R OLL /YAW: +15° TO +45°/ 0°/ 0°
ALL MEASUREMENTS IN: [MILLIMETERS]
INCHES
++
MFQ
[918]
36-1/8”
[640] 25-1/4”
[755]
29-3/4”
[100] 4”
[253] 10”
[695] 27-3/8”
[157] 6-1/4”
[177] 7”
[504]
19-7/8”
[556]
21-7/8”
[365]
14-3/8”
[751]
29-1/2”
15°
45°
NOTE: CUSTOM INTERFACE BRACKET
NOT SHOWN. THE CUSTOM INTERFACE
BRACKET NEEDED FOR YOUR DISPLAY
WILL ADD BETWEEN ½”AND 2” IN DEPTH
AND MAY AFFECT LOCATION OF DISPLAY
ON THE MOUNT. SEE PSBU DRAWING ALSO.
WEIGHT CAPACITY: 200 LBS
HEIGHT ADJUSTMENT: 19-7/8” TO 21-7/8” IN 2” INCREMENTS
(GROUND TO MIDDLE OF SCREEN) TILT/ROLL/YAW: +15° TO +45°/ 0°/ 0°
ALL MEASUREMENTS IN: [MILLIMETERS]
INCHES
++
PFQ
DIMENSIONS
4
Installation Instructions MFM, PFM, MFQ, PFQ
Tighten Fastener
Apretar elemento de fijación Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación Befestigungsteil lösen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis à pointe cruci forme
Open-Ended Wrench
Llave de boca Gabelschlüssel Chave de bocas Chiave a punte aperte Steeksleutel Clé à fourche
By Hand
A mano Von Hand Com a mão A mano Met de hand À la main
Hex-Head Wrench
Llave de cabeza hexagonal Sechskantschlüssel Chave de cabeça sextavada Chiave esagonale Zeskantsleutel Clé à tête hexagonale
Pencil Mark
Marcar con lápiz Stiftmarkierung Marcar com lápis Segno a matita Potloodmerkteken Marquage au crayon
Drill Hole
Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou
Adjust
Ajustar Einstellen Ajustar Regolare Afstellen Ajuster
Remove
Quitar Entfernen Remover Rimuovere Verwijderen Retirez
Optional
Opcional Optional Opcional Opzionale Optie En option
Security Wrench
Llave de seguridad Sicherheitsschlüssel Chave de segurança Chiave di sicurezza Veiligheidssleutel Clé de sécurité
LEGEND
5
MFM, PFM, MFQ, PFQ Installation Instructions
3/16"
(Provided)
A (1)
E (1)
F (2)
G (1)
H (1)
J (1)
L (4)
5/16-18 x 3/4"
P (4)
5/16"
D (1)
C (1)
K (1)
MFM/MFQ Only
PFM/PFQ
Only
(left)
B (1)
(right)
3/16"
MFQ/PFQ Only
MFM/PFM
Only
M (4)
5/16-18 x 2-3/4"
N (4)
5/16-18 x 4-1/4"
Q (1) 3/16"
MFM/PFM
Only
TOOLS REQUIRED FOR INSTALLATION
PARTS
6
Installation Instructions MFM, PFM, MFQ, PFQ
(Front view of cart)
(N) x 4
(F) x 2
(B)
(E)
(A)
1
(Bottom view of cart)
1
2
3
4
(Front view of cart)
(M) x 4
(P) x 4
(C) or (D)
2
(Back view of cart)
(MFM Shown)
(G) or (H)
(L) x 4
(C) or (D)
3
ASSEMBLY
CAUTION:
drill is used to insert button head cap screws. Screws should first be inserted and turned BY HAND with the hex key or with a handheld screwdriver BEFORE using the hex head drill bit (Q) and power drill to complete the attachment.
Assembling Cart
1. Assemble two legs (A) and (B) to the cart cross bracket (E) using two 5/16-18x4-1/4" button head cap screws (N) and one end cap (F) per leg. (See Figure 1)
Attachment holes may be damaged if a power
2. Attach center post (C or D) to leg assembly using four 5/16-18 x 2-3/4" button head cap screws (M) and four 5/16" washers (P). (See Figures 2 and 3)
Figure 3
Figure 1
CAUTION:
drill is used to insert button head cap screws. Screws should first be inserted and turned BY HAND with the hex key or with a handheld screwdriver BEFORE using the hex head drill bit (Q) and power drill to complete the attachment.
NOTE:
Attachment holes may be damaged if a power
Insert and turn screws in order shown (1, 2, 3, 4) in Figure 2.
3. Attach head assembly (G) or (H) to the cart assembly using four 5/16-18 x 3/4" button head cap screws (L). (See Figure 4)
Figure 4
Figure 2
7
MFM, PFM, MFQ, PFQ Installation Instructions
Press down to set brakes
Do NOT let display rest here
1
2
(MFM/PFM shown)
5
4
5
May remove pin and nut and move to lower holes
A padlock or bolt may be placed through latch holes
Attaching Display to Cart
WARNING:
MAY LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s responsibility to ensure the total amount of weight placed on the cart does not exceed 125 lbs (56.70 kg) for the MFM and MFQ, and 200 lbs (90.72 kg) for the PFM and PFQ.
WARNING:
on the back wheels by pressing down on the tab. (See Figure 5)
EXCEEDING MAXIMUM WEIGHT CAPACITY
Before attaching display to cart set the brakes
Figure 5
Figure 7
WARNING:
LBS! Always use two people and proper lifting techniques when installing or positioning display on cart.
5. Lower display into place listening for audible "click" to ensure recessed area of mounting buttons are properly seated in lower area of mounting holes. (See Figures 7 & 8)
DISPLAY MAY WEIGH IN EXCESS OF 40
1. Adjust the cart to the desired height by holding the top p a rt of the post, pulling out knob on the center post and turning
o
in either direction to disengage the locking mechanism.
90
2. Raise or lower the center post, then turn the knob 90o either direction to engage the knob and lock the cart at desired height. (See Figure 6)
IMPORTANT ! : Set the height of the cart so the display does NOT rest on the lower part of the center post. (See Figure 6.) Always set the height so the knob is engaged in a hole in the center post.
3. Attach a PSBU or MSBU interface bracket to the display following the instructions included with the bracket.
4. While supporting both sides of display, align four mounting buttons on display or interface bracket with four mounting holes in head assembly. (See Figures 7 and 8)
8
Figure 6
WARNING:
CART OR DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Ensure mounting buttons are completely engaged in mounting holes.
NOTE:
Holes are provided in the faceplate for use with a padlock or similar locking device, if desired. In addition, the pin and nut may be removed from the upper holes and moved to the lower holes for use as a more permanent locking device. (See Figure 8).
IMPROPER INSTALLATION CAN LEAD TO
Figure 8
Installation Instructions MFM, PFM, MFQ, PFQ
lock display
lock display
1
3
4
(MFM Shown)
Place optional bolt (not provided) here to lock in a midway position (30
o
tilt)
(Rear view of center post)
(Front view of center post)
Exit for
1
2
(J)
cables
3
(MFM/PFM Shown)
Exit for cables
(MFQ/PFQ Shown)
(Front view of center post)
(Rear view of center post)
1
Tilting Display
The display can be tilted from 15o to 45o.
1. Turn knob counterclockwise on back of head assembly to
loosen the tilt. (See Figure 9)
Figure 9
2. Tilt display as desired, to a maximum of 45o either forward
or backward.
3. Turn knob clockwise to tighten display on head assembly.
(See Figure 9)
CAUTION:
prevent damage when moving the cart and display.
4. If leaving the display in a midway position (30o tilt), it is
recommended that a bolt (not provided) be placed through the head assembly (see Figure 9) to lock the display into the midway position.
Tighten knob on back of head assembly to
Cable Management
MFM/PFM Models Only
1. Signal cables and display power cord can be run through
the top and down through the post to exit out the back. (See Figure 10)
2. Any accessory power cords can be run through the front
and down through the post to exit out the back. (See Figure 10)
3. Install the snap-on covers to any opening that is not being used. (See Figure 10)
4. T o remove the snap-on covers, grip the sides of the cover in the middle and pull off. They can also be removed by inserting a flat-blade screwdriver into the bottom slot and rotating the screwdriver.
5. Proceed to Cart Use and Maintenance.
MFQ/PFQ Models Only
1. Signal cables and display/accessory power cords can be run through the top and down through the post to exit out the back. (See Figure 11)
Figure 10
Figure 11
9
MFM, PFM, MFQ, PFQ Installation Instructions
Push cart at or under knob
Do NOT push cart near top
(MFM/PFM models)
x 4
Cart Use and Maintenance
CAUTION:
products and maximum weights indicated (125 lbs (56.70 kg) for the MFM and MFQ, and 200 lbs (90.72 kg) for the PFM and PFQ). Use with other products or products heavier than the maximum weights indicated may result in instability causing possible injury.
WARNING:
OF INJURY. Do not allow children under 16 to move cart. Only adults should move this cart. Move cart slowly. Apply moving force on narrow dimension. Never apply force at top ­always push near middle. Push, don’t pull.
This cart is intended for use only with the
CART CAN TIP OVER RESUL T ING IN RISK
Figure 13
Removing Display from Cart
1. Remove bolt or padlock from faceplate (if used). (See Figure 13)
NOTE:
2. Pull back on flag on upper mounting hole and press pin
The pin may have been used as a more permanent locking device. If so, remove nut and pin and move from the lower holes to the upper holes.
down into "Open" position. (See Figure 13)
Figure 12
1. Always place cart on level surface.
2. Always lock the wheels when the cart is not moving.
3. Check and tighten the hex nuts on the casters occasionally. (See Figure 12) These should be checked especially after use on uneven ground.
WARNING:
40 LBS! Always use two people and proper lifting techniques when installing or positioning display on stand.
3. Carefully lift display from cart.
4. Lift up on pin and place flag back against faceplate to return it to "Closed" position. (See Figure 13)
EACH DISPLA Y MAY WEIGH IN EXCESS OF
10
Installation Instructions MFM, PFM, MFQ, PFQ
2
1
Remove bolt or padlock if used
Pin in "Open" position -
Pin in "Closed" position -
4
move to "Open" position to
move to "Closed" position
remove display
after display is removed.
Figure 14
11
MFM, PFM, MFQ, PFQ Installation Instructions
8809-000042 ©2007 Chief Manufacturing
www.chiefmfg.com
08/07
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P +31 (0)40 2668620 F +31 (0)40 2668615
Asia Pacific A Room 30I, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112
P +86-755-8996 92 26 ; 8996 9236 ; 8996 9220 F +86-755-8996 9217
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use