Page 1
INSTALLATION INSTRUCTIONS
LVS1U
LVSXU
ConnexSys™ Video Wall Mounting System
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
LVS1U / LVSXU
Page 2
LVS1U / LVSXU Installation Instructions
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief®, ConnexSys™, RapidDraw™, and PowerZone™ are
trademarks of Milestone AV Technologies. All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the LVS1U/LVSXU does not
exceed maximum weights listed in table below.
MODEL Maximum Weight Allowed
LVS1U
LVSXU
150 lbs
(68.0 kg)
150 lbs
(68.0 kg)
IMPORTANT ! : The video wall system ships either with rails
(LVS1U) or without (LVSXU). If you’re installing a video wall of
L VSXU mounts you will need to provide the strut channel for
mounting to the wall. (See LET’S GET STARTED!
Measurements You’ll Need section for further information.)
WARNING: A WARNING alerts you to the possibili ty of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
IMPORTANT ! : The LVS1U/LVSXU is designed to be
mounted to:
• a bare 8" thick solid concrete wall. Fasteners must be
placed a minimum of 16" (406mm) and a maximum of
24" (610mm) apart AND within 9" (230mm) of each end
of the rail/strut channel.
• a 5/8" minimum thickness plywood-backed, steel stud
wall covered with drywall having a maximum thickness
of 5/8". Fasteners must be placed a maximum of 8"
(203mm) apart AND in last slots on each end of rail/
strut channel.
• a 2" x 4" wood stud wall covered with drywall having a
maximum thickness of 5/8". Fasteners must be placed
a minimum of 16" (406mm) and a maximum of 24"
(610mm) apart AND within 9" (230mm) of each end of
the rail/strut channel.
NOTE: For installation on a curved wall, the wall radius must
be greater than 200" (508cm).
--SAVE THESE INSTRUCTIONS--
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
2
Page 3
Installation Instructions LVS1U / LVSXU
IMPORTANT SAFETY INSTRUCTIONS .....................................2
TABLE OF CONTENTS ...............................................................3
LEGEND ......................................................................................4
DIMENSIONS ..............................................................................5
TOOLS REQUIRED FOR INSTALLATION .................................6
PARTS .........................................................................................6
LET’S GET STARTED! Measurements You’ll Need ....................7
MOUNTING PATTERN OFFSET CALCULATION ......................8
STRUT CHANNEL REQUIREMENTS (LVSXU) ..........................8
CURVED VIDEO WALLS ON FLAT WALL ..................................9
Calculating Wall Radius .....................................................9
ALLOWING SPACE FOR MOUNT ADJUSTABILITY...................9
ATTACHING STRUT CHANNEL OR RAIL .................................10
HANGING LVS1U/LVSXU MOUNT ON RAIL/STR UT CHANNEL
11
Preparing Strut Channel (LVSXU only) ..................11
Hanging Mounts .....................................................11
INSTALLING INTERFACE BRACKETS ......................................12
ADDING DISPLAYS TO MOUNTS ..............................................12
ADJUSTMENTS ..........................................................................13
COMPLETING THE INSTALLATION ..........................................15
Cable Management Clips .......................................15
Security ...................................................................15
FASTENER INSTALLATION METHODS ....................................15
Wood Stud ..............................................................15
Concrete .................................................................15
Plywood-Backed Steel Stud ...................................16
SERVICE .....................................................................................17
Extending and Retracting Mount ............................17
Interface Bracket Kickstands ..................................17
RapidDraw Display Release ...................................17
TABLE OF CONTENTS
3
Page 4
LVS1U / LVSXU Installation Instructions
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
LEGEND
4
Page 5
Installation Instructions LVS1U / LVSXU
27.56
[700]
MAX DISPLAY
PATTERN WIDTH
17.47
443.7
1.00
25.4
HEIGHT
ADJUST
3.99
101.4
MIN DEPTH
LVS1U
DIMENSIONS: INCHES
[MILLIMETERS]
27.56
[700]
MAX DISPLAY
PATTERN WIDTH
17.47
443.7
1.00
25.4
HEIGHT
ADJUST
3.99
101.4
MIN DEPTH
RAILS NOT INCLUDED IN LVSXU VERSION. 13/16” RAILS
SHOWN FOR DEPTH AND POSITION MEASUREMENTS
ONLY. IF USING A DEEPER STRUT CHANNEL ADD IN THE
ADDITIONAL DEPTH.
DIMENSIONS: INCHES
[MILLIMETERS]
LVSXU
DIMENSIONS
5
Page 6
LVS1U / LVSXU Installation Instructions
#2
nut driver
7/16"
1/2"
7/16"
1/2"
7/16"
1/2"
1/8" x 6"
(included)
3/8"
3/8"
7/32"
3/8"
(Letters correspond to letters on bag)
A (4)
M6 x 12
B (4)
M6 x 16
C (4)
M6 x 30
D (4)
3/16"
E (4)
.75x.344x.5
F (4)
M8 x 12
G (4)
M8 x 16
H (4)
M8 x 25
J (4)
UX10 x 60
K (4)
5/16"
L (4)
5/16" x 2-1/2"
M (10)
N (10)
#14 x 1-1/2"
1/4"
Q (4)
[Cable clip]
P (8)
[7-1/2" cable tie]
U (1)
V (1)
[Rail]
[LVS1U assembly]
X (2)
[Interface
bracket]
OR
U (1)
[LVSXU assembly]
(LVS1U only)
R (2)
[Outer stop
S (2)
T (2)
1/4-20 x 1/2"
W (1)
1/8" x 6"
(LVSXU only)
Cable Management Kit
Display Hardware Kit
Concrete and Wood Stud Walls
Install Hardware Kit
Plywood-backed Walls
Install Hardware Kit
clamp]
[Inner stop
clamp]
PowerZone™ Adjustment Guide
Y (1)
[Label sheet]
Z (1)
TOOLS REQUIRED FOR INSTALLATION
PARTS
6
Page 7
Installation Instructions LVS1U / LVSXU
I
C
D
E
G
FLOOR
CEILING
F
F
LET’S GET STARTED!
Table 1: Measurements You’ll Need
Description Measurement
A - Number of displays in each row
B - Number of displays in each column
C - Width of individual display
D - Height of individual display
E - Total width - (A) x (C)
F - Floor to bottom of display (bottom row) OR Ceiling to top of display
(top row)
G - 1/2 height of display (D) / 2
H - Display mounting pattern offset. Only applies to some displays.
Calculation instructions (See Figure 2)
I - Strut channel length* (E) – 4" (102mm) (LVSXU only)
J - Number of strut channel lengths (B) x 2 (LVSXU only)
R - Radius of curved wall (Curved wall installations only)
* Check with your local strut channel dealer to determine the lengths available. You may need to buy multiple pieces or cut longer
pieces down to size.
Figure 1
7
Page 8
LVS1U / LVSXU Installation Instructions
Center line
of display
Center line
of mounting
pattern
Mounting
pattern of
display
Offset (H)
NOTE: An offset measurement (H) is required if the centerline of the display does not match the centerline of the
display mounting pattern.
1. If display mounting pattern is BELOW display centerline: 8-3/4" - H = Distance from display centerline to rail/
2. If display mounting pattern is ABOVE display centerline: 8-3/4" + H = Distance from display centerline to rail/
strut channel mounting location.
strut channel mounting location.
7/8"
3/8"
L
K
1-5/8"
IMPORTANT! All dimensions other than "L" and "K"
are nominal requirements.
(10mm)
(22mm)
(41mm)
Strut Channel Profile
UNACCEPTABLE strut channel profiles
Strut channel MUST
have
rolled up lips on both sides
of channel.
Strut channel MUST NOT
have holes or slots on
side walls of channel.
MOUNTING PATTERN OFFSET CALCULATION
Figure 2
STRUT CHANNEL REQUIREMENTS (LVSXU)
IMPORTANT ! : Strut channel must be made of steel with a minimum yield strength of 33ksi (230MPa), OR aluminum
(6063-T6, 6005-T5 or stronger) with a minimum yield strength of 30ksi (207MPa), and meeting the profile and dimension
requirements outlined in Table 2, dependent on whether it is a flat wall or curved wall installation. (See Figure 3) and (See
Figure 4)
Table 2: Strut Channel Material and Dimension Requirements
STRUT REQUIREMENTS
MA TERIAL ALUMINUM STEEL
Minimum Yield Strength 30ksi (207MPa) 33ksi (230 MPa)
Material Thickness [0.078"] (2mm) 14 ga [0.075"] (2mm)
or 12ga [0.104"] (2.5mm)
K (Flat wall) 13/16" (21mm) or 7/8" (22mm) 13/16" (21mm) < K < 3-1/4" (83mm)
K (Curved wall) 13/16" (21mm) or 7/8" (22mm)
R - Minimum Wall Radius > [200"] (50.8m) > [400"] (101.6m)
L - Flange Length 1/4" (6mm) < L < 9/32" (7mm)
8
Figure 3
Figure 4
Page 9
Installation Instructions LVS1U / LVSXU
EXAMPLE:
Stick/St rut Length
48 inches
Gap
0.375 inches
Radius (R)
768.1875 inches
Radius = Gap/2 + (Length/8 x Length/Gap)
Radius = 0.375/2 + (48/8 x 48/0.375)
Gap
(view from above)
Flat stick or strut
Curved wall
48.9"
28.3"
48.9" x 3 screens x 0.00104" (depth adjustment factor) = 0.153"
CURVED VIDEO WALLS ON FLAT WALL
• 5.5° is the maximum angle a mount can make from vertical;
• Two or more mounts placed side-by-side can create a maximum angle of 11° (on a flat wall);
• All other requirements/restrictions listed in Table 2 still apply.
CALCULATING WALL RADIUS
1. Place a rigid, flat stick or channel strut (at least 3 ft or 1m long, but preferably longer) against the curved wall. Do NOT bend the
stick or strut.
2. Measure the largest gap between the stick/strut and the wall.
Figure 5
ALLOWING SPACE FOR MOUNT
ADJUSTABILITY
IMPORTANT ! : In order to enable the most adjustability
within the video wall, include some extra depth when
planning the installation.
As a rule of thumb, assume the mount is 4.5" deep and add
0.125" for every 10’ of displays [1"/120" x 0.125" = 0.00104"]
EXAMPLE: With a 4x3 Portrait video wall where the height is
48.9" x 3 and the width is 28.3" x 4. (See Figure 6):
• take the longest dimension (height) and multiply it
by 0.00104 (or 1"/120" x 0.125")
48.9" x 3 x 0.00104" = 0.153"
For this example, you would then install under the assumption
the depth will be 4.5" + 0.153".
Table 3: Depth Adjustment Factor
WALL
TYPE
Flat walls N/A 0.00104" per inch
Curved walls
Curved walls 200"<Radius<500" 0.00312" per inch
NOTE:
The maximum mount thickness to design into the
installation is 7.00".
RADIUS DEPTH ADJUST
Radius >500"
FACTOR
0.0025" per inch
Figure 6
9
Page 10
LVS1U / LVSXU Installation Instructions
Top rail - LVS1U
Top strut channel - LVSXU
Ceiling
Centerline - display
Centerline - display
C
I
D
1
2
3
Floor
1
2
3
5
7
H
C
D
ATTACHING STRUT CHANNEL OR RAIL
IMPORTANT ! : Reference measurements noted on
page 7.
1. Mark distance (F) from floor to desired location for bottom
of display OR from ceiling to desired location for top of
display (if installing top row first). (See Figure 1) and (See
Figure 7)
2. Mark distance (G) from bottom of display (or top of display)
to center line of display. (See Figure 1) and (See Figure 7)
3. Measure up 8-3/4" (222mm) from centerline of display and
mark location for top strut channel/rail attachment.
NOTE: If an offset measurement (H) is needed (See Figure 2):
• If display mounting pattern is BELOW display
centerline, measure up: 8-3/4" (222mm) - H
• If display mounting pattern is ABOVE display
centerline, measure up: 8-3/4" (222mm) + H
4. Level and attach strut channel/rail (V) using the provided
hardware. See Parts drawing, (See Figure 7) and (See
Table 4).
5. Mark distance (D) (up or down) from first strut channel/rail
slots and mark location of next row of strut channel/rail.
6. Repeat for remaining rows of strut channels/rails.
7. (L VSXU only) Proceed to Hanging LVS1U/LVSXU Mount
On Rail/Strut Channel section.
8. (LVS1U only) Measure over (C) (width of display) from
center of first installed rail, level and mark location of
adjacent rail. (See Figure 1) and (See Figure 7)
9. Repeat Step 8 for remaining rails in that row.
10. Attach upper rails (V) using Fastener Information. (See
Table 4)
11. Measure up from attached rails the distance (D) and mark
for next row of rails (V). (See Figure 1) and (See Figure 7)
12. Repeat Steps 4 - 10 for that row of rails.
13. Repeat Step 11 for any remaining rows of rails (V).
IMPORTANT ! : See Fastener Installation Methods section
at end of Installation Instructions for details on installing product
into various wall types.
Table 4: Fastener Information
WALL
TYPE
Drywall
attached to
plywoodbacked walls
/Steel studs
Wood stud
(2" x 4")
Concrete
PILOT
HOLE
N/A #14 x 1-1/2" hex slot head screw
7/32" x 3"
3/8" x 3" 5/16 x 2-1/2" hex head lag (L) &
FASTENERS (see PARTS
drawing)
(N) & 1/4" washer (M). Fasteners
placed a maximum of 8" (203mm)
apart AND
rail/strut channel.
5/16 x 2-1/2" hex head lag (L) &
5/16" washer (K). Fasteners placed
at stud locations, min. 16" (400mm)
and max. 24" (610mm) AND within 9"
(230mm) of each end of the rail/strut
channel.
Fischer UX10x60 anchor (J).
Fasteners placed a min. 16" (400mm)
and max. 24" (610mm) apart AND
within 9" (230mm) of each end of the
rail/strut channel.
in last slots on each end of
10
Figure 7
Page 11
Installation Instructions LVS1U / LVSXU
(R)
(S)
1
2
(T)
Stop clamp fastened
in place at each end
of upper row of
strut channel
(LVS1U shown as example)
1
1
lower lip of strut
channel or rail
3
3
side
view
mount hooks
strut channel
upper lip
lower strut
channel
wall
4
x 2
RapidDraw
pull cord
HANGING LVS1U/LVSXU MOUNT ON RAIL/
STRUT CHANNEL
Preparing Strut Channel (LVSXU only)
1. On the top rail, slide one inner stop clamp (S) into end of
strut channel section. (See Figure 8)
2. Fasten outer stop clamp (R) to inner stop clamp (S) using
one 1/4-20 x 1/2" hex head screw (T). (See Figure 8)
3. Repeat for each end of each top section of strut channel.
Hanging Mounts
1. Lift mount and hang it on lower lip of upper strut channel or
rail (V). (See Figure 9)
2. Repeat for remaining mounts in that row, and slide mounts
along rails/strut channels to desired location.
3. LVSXU only: Add lower strut channel to bottom of all
mounts in row by lifting strut channel up from below mounts
and setting upper lip of strut channel onto mounts’ latching
hooks. (See Figure 10)
Figure 8
Figure 9
Figure 10
4. Tighten two hex head fasteners at bottom of each mount.
(See Figure 11)
Figure 11
5. Fasten bottom rail (LVS1U) or lower strut channel (LVSXU)
to wall using the provided hardware. See Parts drawing,
and (See Table 4).
6. Extend RapidDraw pull cord to bottom row of displays so
that it is accessible, re-tie to correct length and label the pull
cord using label (Y) so that it is identifiable. (See Figure 11)
IMPORTANT ! : See Service section for more
information on properly configurating the RapidDraw cord
and display release.
7. Repeat Attaching Strut Channel or Rail and Hanging
L VS1U/LVSXU Mount On Rail/Strut Channel sections for
each row of displays.
11
Page 12
LVS1U / LVSXU Installation Instructions
6
(A-C or F-H) x 4
(D) x 4
(E) x 4, if
required
(X)
5
Match diamond
with center of
display
Bracket kickstand
may be raised to
allow hardware
attachment
Interface
bracket
hooked over
mount
(Display not shown)
(LVS1U shown
as example)
1
1
4
4
5
INSTALLING INTERFACE BRACKETS
1. Place displays face down on a soft, non-abrasive surface.
CAUTION: Using screws of improper diameter may
damage your display! Proper screws will easily thread into
display mounting holes.
2. Select screw diameter by examining hardware (A-C and F-H)
(6mm or 8mm) and comparing with mounting holes on
display. (See Figure 12)
3. Select spacers:
• Spacers are NOT required if mounting holes are not
recessed and interface brackets (X) can lay flat against
display.
• Spacers (E) ARE required if mounting holes are
recessed, or if protrusions prevent interface brackets
(X) from laying flat.
CAUTION: Using screws of improper length may damage
your display! Proper screws will have adequate thread
engagement without contacting bottom of display mounting
holes.
4. Select screw length: (See Figure 12)
• By hand, insert SHORTEST length screw of selected
diameter (A or F) through 3/16" washer (D, if using
screw A), bracket (X), selected spacer (E, if required),
into display mounting hole. Do NOT thread screw into
hole at this time.
• Proper screw length requires base of screw head to
protrude above flat washer (if flat washer is used) a
distance equal to or greater than the screw diameter. If
screw length is inadequate, select longer screw. Select
shortest screw which will protrude the required
distance.
5. Make sure diamond on interface brackets is even with
center of display. (See Figure 12)
6. Use selected screws (A-C or F-H), washers (D, if using
screws A, B or C) and spacers (E), if necessary, to connect
interface brackets (X) to back of display. (See Figure 12)
ADDING DISPLAYS TO MOUNTS
1. Raise display with attached interface brackets and hook top
of brackets into top of mount. (See Figure 11)
2. Slowly bring bottom of display in towards mount until it clicks
into place.
3. Repeat Steps 1 and 2 for remaining mounts in that row.
12
Figure 12
Figure 13
4. The displays can be easily removed by pulling both
interface bracket cords down. (See Figure 13)
5. Pull the bottom of the display out.
6. Lift up display to lift hooks off the mount.
Page 13
Installation Instructions LVS1U / LVSXU
1
2
2
3
3
(Display not shown)
6
5
4
Tab
Latch
Interface
bracket
ADJUSTMENTS
NOTE: The following steps are also referenced on the next
page (See Figure 18) and the PowerZone
Adjustment guide (Z).
1. Place the level against the front of the display and use knob
(#1 in Figure 18) to straighten the tilt. (See Figure 14)
Figure 16
4. Slide latch mechanism until tab sits flush against the
interface bracket.
5. Pull tab forward to lock latch mechanism to interface
bracket. (See Figure 17)
6. Push latch down to engage the micro lateral adjustment
knobs (#4B and #4C in Figure 18). (See Figure 17) and
(See Figure 18)
7. Turn micro lateral adjustment knobs clockwise to move
display toward knob end until displays are in correct
Figure 14
position. (See Figure 18)
2. Place a level on top of display and use the knobs at the top
of the interface brackets (#2 in Figure 18), to raise/lower
each side of display and level the display. (See Figure 15)
and (See Figure 18)
3. Place level across face of adjoining screens and adjust
depth (#3 in Figure 18) to make displays flush across the
front of the video wall. (See Figure 16) an d (S ee Fi gure 18 )
Figure 15
Figure 17
13
Page 14
LVS1U / LVSXU Installation Instructions
Tilt adjust
Height adjust
Depth adjust
Micro-lateral shift latch
Micro-lateral shift: Clockwise moves display towards knob end
Micro-lateral shift: Clockwise moves display towards knob end
Display release
14
Figure 18
Page 15
Installation Instructions LVS1U / LVSXU
1
(Q)
Insert
padlock
1
2
(L) x 2
1
2
(L)
(J)
COMPLETING THE INSTALLATION
Cable Management Clips
1. Place cable clip (Q) into rail/strut channel and turn 90° in
either direction until cable clip is vertical. (See Figure 19)
2. Route cables and RapidDraw release cords along rails/strut
channels, through cable clips.
3. Fasten cables and cords to cable clips (Q) using cable ties
(P).
FASTENER INSTALLATION METHODS
IMPORTANT ! : (See Table 4) for appropriate hardware
and pilot hole sizes for various wall types.
Wood Stud
1. Use one 5/16" x 2-1/2" lag bolt (L) through product and into
pilot hole. (See Figure 21)
2. Repeat for remaining pilot holes.
Figure 21
Figure 19
Security
The displays may be secured to the mounts by using a padlock
(not included) through the bottom of the interface brackets.
(See Figure 20)
NOTE: Padlock must have a 1/4" (6mm) shackle diameter.
Concrete
1. Install one UX10 x 60 anchor (J) into each pilot hole using a
hammer, making sure that the anchor is flush with the wall.
(See Figure 22)
2. Use one 5/16" x 2-1/2" lag bolt (L) through product into each
anchor in wall.
Figure 22
Figure 20
15
Page 16
LVS1U / LVSXU Installation Instructions
Steel Stud (2 x 4 / 25ga minimum)
FRONT
There must be a minimum of
1-7/8" (48mm) clearance
inside wall
16" or 24" (on center) Studs
If back side of wall is unfinished, drywall must be installed
to a minimum of one stud left and right of the stud(s)
being used to install the mount. Drywall must be
secured to studs with screws a maximum of 12" (305mm) apart down center of stud.
Stud type and structural strength must conform to the North American
Specification for the Design of Cold-Formed Steel S tructural Members.
5/8" maximum
drywall thickness
(Both Sides of Stud)
[362 S 125 18, C-Shaped, S-Stud Section]
Plywood
5/8" minimum thickness
plywood (5 layers) covered
with drywall having
maximum thickness of 5/8"
Plywood-Backed Steel Stud
1. Use one #14 x 1-1/2" hex-head washer slot head screw (N) and one 1/4" washer (M) through strut channel or rail. (See Figure 23)
16
Figure 23
Page 17
Installation Instructions LVS1U / LVSXU
Interface bracket
release cords
2
1
(Display not shown)
Kickstand
3
Mount ships with
cord attached here
2
To release display from
left or above,
reinstall cord
here
SERVICE
Extending and Retracting Mount
The mounts may be extended and retracted only in a service
situation.
1. To Extend Mount
designated for the specific mount.
2. When the mount releases, carefully grasp bezel edges of
display and pull out slowly, being careful to clear
surrounding displays.
3. To Retract Mount: Carefully push against display bezel
edges, being careful to clear surrounding displays.
4. Push display against mount until it clicks into place.
Interface Bracket Kickstands
The interface brackets are equipped with kickstands which must
be used in a service situation.
only
1. Pull down on interface bracket release cords. (See Figure 24)
2. Pull out bottom of display.
3. Flip down the kickstands on both interface brackets, and
prop against mount during service.
: Pull on the RapidDraw release cord
RapidDraw Display Release
The RapidDraw pull cord and display release allows easy
service access to any specific display in the video wall.
Each mount ships with the pull cord installed. It is installed so
that when pulled from below the mount or from the right of the
mount it will release the display for service.
The following steps should be taken if an installation requires
that the pull cord be accessible from the left of the display or
above the display:
1. Unhook the pull cord from the mount. (See Figure 25)
2. Reinstall the pull cord in the opposite hole on the mount.
(See Figure 25)
4. After service, hold display while flipping up both kickstands.
5. Slowly bring bottom of display in towards mount until it clicks
into place.
Figure 24
Figure 25
17
Page 18
Installation Instructions LVS1U / LVSXU
18
Page 19
LVS1U / LVSXU Installation Instructions
19
Page 20
LVS1U / LVSXU Installation Instructions
Chief, a products division of
Milestone AV Technologies
8800-002638 Rev02
2016 Milestone AV Techn ologies
www.milestone.com
05/16
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000
F 877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852
F +31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
Loading...