Page 1
INSTALLATION INSTRUCTIONS
FUSION PORTRAIT MICROADJUSTABLE LARGE TILT MOUNT
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
LTMPU
Page 2
LTMPU Installation Instructions
DISCLAIMER
Milestone AV Technologies, and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! :
mounted to an 8" concrete, 8"x8"x16" concrete block or 2" x 4"
wood studs (16" on center) wall.
The LTMPU mounts are designed to be
--SAVE THESE INSTRUCTIONS--
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8” (1.6cm) for
wood studs.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the LTMPU up to (and
including) the display does not exceed 200 lbs (90.7 kg).
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
2
Page 3
Installation Instructions LTMPU
75.0
2.95
00.0
125.0
4.92
273.110.7
5
6.87
174.6
2.95
75.0
3.94
100.0
5.69
144.4
3.94100.0 5.90149.7 8.10205.9 10.75273.13.94100.05.90149.7 8.10205.
9
0
0.0
16.00
406.4
8
.00
2
0
3.2
0
.5012.73.8196.8
8.002
0
3.2
0.50
12.73.8196.8 00
.
0
NOTES:
NOT RECOMMENDED FOR SINGLE STUD MOUNTING
MAX SCREEN MOUNTING PATTERN
20.7" (525.8 mm) WIDE X 31.5" (800.1 mm) HIGH
MIN SCREEN MOUNTING PATTERN WIDTH 7.874" (200 mm)
MAX SCREEN SCREW SIZE 8 mm
MAX MOUNTING PATTERN IS 21.6" (548.6 mm) WITHOUT REVERSING UPRIGHTS
MAX MOUNTING PATTERN IS 26 . 2 " ( 665.5 mm) WITH REVERSING UPR IGHTS
FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK
ENGAGEMENT IS .42" (10.7 mm)
RAILS CAN BE SLID LEFT OR RIGHT FOR OFFSET APPLICATIONS
MOUNT IS 1.99" (50.5 mm) DEEP WHEN FLAT TO THE WALL
16.53
10.5
6.94
176.2
177.8
7.00
419.9
34.38
873.1
0.75
19.1
0.98
25.0
87.5
3.44
8.1
0.32
1.97
50.0
0.49
12.5
3.37
85.7
15.10
383.4
22.57
573.3
6.00
152.4
MEASUREMENTS IN: [MILLIMETERS]
INCHES
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
DIMENSIONS
LEGEND
3
Page 4
LTMPU Installation Instructions
#2
7/32” (5.5mm) Wood Stud
3/8” (9.5mm) Concrete
3/16” (included)
M5 (included)
G3 (6)
G5 (6)
A (1)
B (1)
G1 (8)
M4x16mm
G2 (6)
M4x20mm
M4x25mm
G4 (6)
M5x16mm
M5x20mm
G6 (6)
M5x25mm
G7 (6)
M6x16mm
G8 (6)
M6x25mm
G15 (1)
M5
G9 (6)
M8x20mm
G10 (6)
M8x30mm
G11 (4)
M8x50mm
G13 (8)
.750x.323x.250
G14 (8)
.750x.344x.500
G12 (8)
E1 (4)
UX10
E3 (4)
5/16”
E2 (4)
5/16” x 2-1/2”
D (2)
G (1)
F (1)
F1 (8)
5/16”
F2 (8)
5/16” x 1/2”
F3 (1)
3/16” X 6"
[Wall Mount]
[Left Upright]
C (1)
[Right Upright]
[Universal
Washer]
[Display Bracket]
E (1)
TOOLS REQUIRED FOR INSTALLATION
PARTS
4
Page 5
Installation Instructions LTMPU
Center of screen
7-1/2”
Vertical center
of mount
[190.5mm]
5
INSTALLATION
The LTMPU mounts are designed to be mounted to an 8"
concrete, 8"x8"x16" concrete block or 2" x 4" wood studs (16"
on center) wall.
be tilted.
Locate Mounting Site
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJUR Y
OR DAMAGE TO EQUIPMENT! It is the installers
responsibility to make certain the structure to which the
mount is being attached is capable of supporting five times
the weight of the LTMPU and all attached equipment not to
exceed 200 lbs (90.7 kg).
NOTE: Proceed to either the Installing to a Wood Stud Wall
Installing to a Wood Stud Wall
1. Determine the center of the TV screen, and where it should
be located on the wall.
WARNING: The LTMPU is designed to be mounted to two
wood studs (16" on center) or concrete. DO NOT attemp t to
mount the LTMPU to a single wood stud!
The LTMPU has brackets which allow the TV to
section or the Installing to a Concrete Wall section.
5. Using a level, mark the wall on each stud to attach the
mount through the upper mounting slots. (See Figure 2)
Figure 2
2. Locate the closest studs to the left and right of the selected
location.
3. Line up the notches on mount with center of screen marking
to determine vertical center. (See Figure 1)
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL CORDS OR CABLES
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surface is free
of electrical wires and cables before drilling or installing
fasteners.
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH
OR SERIOUS PERSONAL INJURY! AL WAYS make certain
area behind mounting surface is free of gas, water, waste, or
any other plumbing before cutting, drilling, or installing
fasteners.
Figure 1
4. Measure up 7-1/2” (190.5mm) from the center point to mark
location of the upper mounting slots.
5
Page 6
LTMPU Installation Instructions
x
6
x 4
9
7
10
(E2) x 2
(E2) x 2
(E3 x 4)
5
6
(E1) x 2
10
9
7
11
(E2) x 2
(E3 x 4)
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH
OR SERIOUS PERSONAL INJURY! AL WAYS make certain
area behind mounting surface is free of gas, water, waste, or
any other plumbing before cutting, drilling, or installing
fasteners.
Figure 3
6. Drill one 7/32” (5.5mm) pilot hole in each stud.
7. Use two 5/16 x 2-1/2” lag bolts (E2) and two 5/16” flat
washers (E3) to attach top of mount to wall. (See Figure 3)
8. Mark the attachment points for the lower mounting slots,
making sure the attachment point s are located on the studs.
(See Figure 3)
9. Drill 7/32” (5.5mm) pilot holes at markings for lower
mounting holes. (See Figure 3)
10. Use two 5/16 x 2-1/2” lag bolts (E2) and two 5/16” flat
washers (E3) to attach the mount to the wall through the
lower mounting holes. (See Figure 3)
11. Slide rails to approximate center of screen location.
Installing to a Concrete Wall
1. Determine the center of the TV screen, and where it should
be located on the wall.
2. Line up the notches on mount with center of screen marking
to determine vertical center. (See Figure 1)
3. Measure up 7-1/2” (190.5mm) from the center point to mark
location of the upper mounting slots. (See Figure 1)
4. Using a level, mark the wall through both upper mounting
slots. (See Figure 4)
Figure 4
5. Drill one 3/8” x 3-1/2" pilot hole at each marking.
6. Install an anchor (E1) into each pilot hole using a hammer.
7. Use two 5/16 x 2-1/2” lag bolts (E2) and two 5/16” flat
washers (E3) to attach top of mount to anchors in wall.
8. Mark the attachment points for the lower mounting slots.
(See Figure 4)
9. Drill one pilot hole at each marking for lower mounting
holes. (See Figure 4)
10. Install an anchor (E1) into each pilot hole using a hammer.
11. Use two 5/16 x 2-1/2” lag bolts (E2) and two 5/16” flat
washers (E3) to attach the mount to the wall through the
lower mounting holes. (See Figure 4)
12. Slide rails to approximate center of screen location.
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL CORDS OR CABLES
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surface is free
of electrical wires and cables before drilling or installing
fasteners.
6
Page 7
Installation Instructions LTMPU
Center of
Bracket
(G13 or G14)
(G12)
(G1 through G11)
(D)
Display
(F2) x 8
1
Center of
Upright
(F1) x 8
(D)
(B)
(C)
(D)
(F2)
(F1)
Attaching Display Brackets to Display
1. Horizontally align the center of the display brackets (D) with
center of screen. (See Figure 5)
NOTE: The notch in the top and bottom of the display bracket
(D) corresponds to the center of the bracket.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display. Properly sized
screws will easily and completely thread into display
mounting holes. If spacers are required, be sure to use longer
screws of the same diameter.
Attaching Uprights to Display Brackets
1. Vertically align the center of the uprights (B and C) with
center of screen. (See Figure 6)
NOTE: The diamond-shape opening in the uprights (B and C)
corresponds to the vertical center of the upright.
2. Attach uprights (B and C) to the display brackets (D) on the
display back using eight 5/16” x 1/2” button head cap
screws (F2) and eight 5/16” flat washers (F1).
IMPORTANT ! : Attach uprights with four screws per
display bracket (D), two at each end. If possible, attach
the uprights with one screw in a top hole and one
diagonally located in a lower hole on each end of the
display bracket. (See Figure 7) At the minimum, one
screw should be in a top hole, and one in a bottom hole
at each end of the display bracket.
Figure 5
2. Select correct screws, spacers (if necessary) and washers
from the hardware bag and attach display brackets (D) to
back of screen. (See Figure 5)
Figure 6
Figure 7
7
Page 8
LTMPU Installation Instructions
4
1
6
Latch
open
Latch
closed
Upright bracket tab
Mounting Slot
Blocked
1 2
(Screen not shown for clarity)
Upright
bracket knob
(Screen not shown for clarity)
1
3
Attaching Display to Wall Mount
1. Push upright brackets tabs all the way down so that the
lower mounting slot is blocked. (See Figure 8)
2. Hang the top hook of upright brackets onto the top bar of the
mount. The bottom of the screen will be away from the wall.
3. Route cables between wall and bars.
CAUTION: PINCH POINTS! Keep fingers, hands and
cables out of pinch point areas.
Figure 8
4. Move screen towards the wall by pulling display bottom
away from wall and pushing the upright brackets tabs up
one notch to the detent which you will be able to feel
(approximately half way up). (See Figure 8)
5. Push bottom of display toward the wall bracket so that lower
latch on upright brackets surrounds lower bar of wall mount.
6. Raise upright brackets tabs all the way to secure the
brackets onto the wall mount. (See Figure 8)
Adjusting Roll/Height of Wall Brackets
NOTE:
1. Use 3/16” hex key (F3) to turn height-adjust screws to right
2. Use 3/16” hex key (F3) to turn height-adjust screws to left
The height adjust wall bracket allows adjustment of
+/- 1/2”.
(tighten) to raise side of screen. (See Figure 9)
(loosen) to lower side of screen. (See Figure 9)
Figure 9
Adjusting Tilt of Upright Brackets
WARNING: IMPROPER TILT ADJUSTMENT MAY LEAD
TO DISPLAY TIPPING FORWARD CAUSING PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Hold display while
loosening upright bracket knobs.
1. Turn upright bracket knobs t o lef t to l oosen ti lt. (See Fi gure
10)
2. Adjust tilt as required.
3. Lock at desired tilt by turning upright bracket knobs to right
to tighten. (See Figure 10)
8
Figure 10
Page 9
Installation Instructions LTMPU
Add padlock
(Optional)
Locking Mount (Optional)
Add padlock (not included) to upright bracket tab to lock the
LTMPU mount. (See Figure 11)
Figure 11
9
Page 10
LTMPU Installation Instructions
10
Page 11
Installation Instructions LTMPU
11
Page 12
LTMPU Installation Instructions
Chief Manufacturing, a products division
of Milestone AV Technologies
8800-002374 Rev03
2013 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
07/13
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000
F 877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852
F +31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
Loading...