CHIEF Fusion FCA803, Fusion FCA813 Installation Instructions Manual

Download

Page 1

I N S T A L L A T I O N I N S T R U C T I O N S

Fusion™ Small Above/Below Accessory Shelf

Above Cart/Ceiling

Below Cart/Ceiling

Above Wall

(FCA813 shown)

Below Wall

Spanish Product Description German Product Description

Portuguese Product Description

Italian Product Description

Dutch Product Description

French Product Description

FCA803/813

Page 2

FCA803/813 Installation Instructions

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively “Milestone”), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

WARNING: Use of this accessory will decrease the weight

capacity of the mounting system to which it is attached by the combined weight of the accessory and all components supported by this accessory! See Figure below for reference.

standard weight limit of mounting system -

(weight of FCA803/813 shelf + shelf components)

DEFINITIONS

MOUNTING SYSTEM: A MOUNTING SYSTEM is the

primary Chief product to which an accessory and/or component is attached.

ACCESSORY: AN ACCESSORY is the secondary Chief

product which is attached to a primary Chief product, and may have a component attached or setting on it.

2 lbs (0.9 kg)

COMPONENT: A COMPONENT is an audiovisual item

designed to be attached or resting on an accessory or mounting system such as a video camera, CPU, screen, display, projector, etc.

WARNING: A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the corresponding instructions.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all accessories are properly assembled and installed using the instructions provided.

WARNING: Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the weight mounted to

the FCA803/813 shelf does not exceed 2 lbs (0.9 kg).

WARNING: Use this accessory only for its intended use as

described in these instructions. Do not use attachments not recommended by the manufacturer.

WARNING: Never operate this accessory if it is damaged.

Return the accessory to a service center for examination and repair.

WARNING: Do not use this product outdoors.

WARNING: RISK OF INJURY TO PERSONS! Do not use

this accessory to support video equipment such as televisions or computer monitors.

--SAVE THESE INSTRUCTIONS--

Page 3

Installation Instructions FCA803/813

16.8-18.3

[426.7-464.8]

[304.8-363.2]

17.5-19.0

[444.5-482.6]

[330.2-381.0]

OVERALL MAX

CENTER OF MOUNT

FUSION WALL ABOVE MOUNT SETUP

15.6-18.2

[396.2-462.3]

[284.5-348.0]

OVERALL MAX

CENTER OF MOUNT

16.7-19.2

[424.2-487.7]

DIMENSIONS - FCA803

540.74

21.29

578.84

22.79

424.67

16.72

OVERALL MIN

12.0-14.3

MIN RANGE

13.0-15.0

MIN RANGE

MAX RANGE

104.76

4.12

578.84

22.79

592.56

23.33

415.42

16.36

OVERALL MIN

12.2-14.2

11.2-13.7

MIN RANGE

MAX RANGE

133.35

5.25

Page 4

FCA803/813 Installation Instructions

27.9 - 29.4

[708.7 - 746.8]

[523.2 - 566.4]

18.3 - 20.0

28.0 - 31.0

[711.2 - 787.4]

DIMENSIONS - FCA813

892.56

878.85

35.14

34.60

670.70

26.41

19.0 - 21.7

20.6 - 22-3

MIN RANGE

MAX RANGE

878.85

34.60

593.71

23.37

892.56

35.14

MAX RANGE

Page 5

Installation Instructions FCA803/813

LEGEND

Tighten Fastener

Apretar elemento de fijación Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations

Loosen Fastener

Aflojar elemento de fijación Befestigungsteil lösen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations

Hex-Head Wrench

Llave de cabeza hexagonal Sechskantschlüssel Chave de cabeça sextavada Chiave esagonale Zeskantsleutel Clé à tête hexagonale

Phillips Screwdriver

Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis à pointe cruciforme

Open-Ended Wrench

Llave de boca Gabelschlüssel Chave de bocas Chiave a punte aperte Steeksleutel Clé à fourche

TOOLS REQUIRED FOR INSTALLATION

PARTS

C (2)

[Shelf bracket]

[Upright bracket]

B (1) [Main bracket]

D (1)

[Shelf]

3/8”

E (1)

[Center washer]

F (4)

[Large washer]

G (1)

[Small washer]

5/32” (included)

1/8” (included)

H (5)

1/4-20 x 1/4”

J (3) 1/4-20 x 1/2”

K (1)

1/4-20 X 5/8”

L (1)

1/4-20 x 3/8”

M (4) 1/2”

N (4)

1/4-20 x 7/16”

P (1) 5/32”

Q (1) 1/8”

Page 6

FCA803/813 Installation Instructions

ASSEMBLY AND INSTALLATION

Below Installation

NOTE: FCA803 and FCA813 shelves may be installed above

or below displays. To install above display, proceed to “Above Installation” Section.

Assembling Shelf to Upright Bracket

1. Loosely install two 1/4-20 x 1/2” button head cap screws (J) into lowest holes on upright bracket (A). (See Figure 1) or (See Figure 2)

2. Hang shelf support (D) onto two screws installed in Step 1. (See Figure 1) or (See Figure 2)

3. Tighten two screws to ensure upright bracket (A) is securely attached to shelf support (D). (See Figure 1) or (See Figure 2)

(Below Wall)

(D)

Attaching Shelf to Wall Mount

NOTE: If attaching to cart or ceiling mount, proceed to Attach

Shelf to Cart/Ceiling Section.

1. Use two 1/4-20 x 1/4” button head cap screws (H) and two large washers (F) to secure shelf bracket (C) to main bracket (B). (See Figure 3)

CAUTION: Slide bracket with caution so that the bracket

does not scratch or damage the wall!

2. Slide main bracket (B) behind wall mount rails until shelf bracket (C) rests on top of wall mount rail. (See Figure 3)

(Below Wall)

(H) x 2

(F) x 2

(C)

(B)

(Below Cart/ceiling)

(D)

Figure 1

tighten

(J) x 2

(A)

Figure 3

3. Slide second shelf bracket (C) underneath lower rail on wall mount, lining up holes on shelf bracket (C) to main bracket (B). (See Figure 4)

4. Use two 1/4-20 x 1/4” button head cap screws (H) and two large washers (F) to secure shelf bracket (C) to main bracket (B). (See Figure 4)

(Below wall)

wall mount rails

(F) x 2

(H) x 2

(C)

Figure 2

tighten

(J) x 2

(B)

Figure 4

Page 7

Installation Instructions FCA803/813

NOTE: Refer to Table 1 and dimension drawings on pages 3-

4 to determine the extension level based on extension distance from mount center.

Table 1: Below Wall Mount

Extension distance from center of

mount (in.)

12.0-14.3 Minimum (FCA803)

14.3-16.8 Intermediate (FCA803)

16.8-18.3 Maximum (FCA803)

19.0-21.7 Minimum (FCA813)

21.7-26.9 Intermediate (FCA813)

26.9-28.4 Maximum (FCA813)

NOTE: Minimum and maximum configurations are shown

below. Intermediate configuration is the same.

5. Use 1/4-20 x 5/8” hex head flange bolt (K) and center washer (E) to secure upright bracket (A) to main bracket (B). (See Figure 5)

(Below wall - minimum)

(FCA813 shown)

Attaching Shelf to Cart/Ceiling Mount

IMPORTANT ! : If installing to a 2x1 display cart using

the FCA623 accessory, proceed to “Installing to FCA623 Accessory” Section (Step 6).

1. Use two 1/4-20 x 1/4” button head cap screws (H) and two large washers (F) to secure shelf bracket (C) to main bracket (B). (See Figure 6)

2. Slide main bracket (B) onto front of cart/ceiling mount head assembly until shelf bracket (C) rests on top of head assembly. (See Figure 6)

(Below cart/ceiling - Standard) (rear view)

(F) x 2

(H) x 2

(C)

(B)

(K)

(Below wall - maximum)

(K)

(E)

(B)

(A)

Figure 6

3. Slide second shelf bracket (C) underneath head assembly, lining up holes on shelf bracket (C) to holes on main bracket (B). (See Figure 7)

4. Use two 1/4-20 x 1/4” button head cap screws (H) and two large washers (F) to secure shelf bracket (C) to main bracket (B). (See Figure 7)

(Below cart/ceiling - Standard)

(C)

(rear view)

(B)

Figure 5

(A)

5. Proceed to Step 11.

(H) x 2

Figure 7

(F) x 2

Page 8

FCA803/813 Installation Instructions

(Below cart with FCA accessory)

Installing to FCA623 Accessory

IMPORTANT ! : Steps 6-10 only apply if installing to

FCA623 accessory.

6. Use two 1/4-20 x 7/16” button head cap screws (N), two large washers (F) and two 1/2” spacers (M) to secure shelf bracket (C) to main bracket (B). (See Figure 8)

7. Slide main bracket (B) onto front of cart/ceiling mount head assembly until shelf bracket (C) rests on top of head assembly. (See Figure 8)

(Below cart with FCA623 accessory) (rear view)

(F) x 2

(H) x 2

(B)

(M) x 2

(C)

NOTE: Refer to Table 2 and dimension drawings on pages 3-

4 to determine the extension level based on extension distance from mount center.

Table 2: Below Cart/Ceiling Mount

Extension distance from center of

11. Use 1/4-20 x 5/8” hex head flange bolt (K) and center washer (E) to secure upright bracket (A) to main bracket (B). (See Figure 10)

NOTE: Maximum configuration is shown below. Several

(FCA813 shown)

(rear view) (Below Cart/Ceiling Minimum)

mount (in.)

11.2-13.7 Minimum (FCA803)

13.7-15.6 Intermediate (FCA803)

15.6-18.2 Maximum (FCA803)

18.3-20.0 Minimum (FCA813)

20.0-26.7 Intermediate (FCA813)

26.7-30.0 Maximum (FCA813)

intermediate configurations are possible depending on which holes are used.

(B)

(A)

(B)

Figure 8

8. Slide second shelf bracket (C) underneath head assembly, lining up holes on shelf bracket (C) to holes on main bracket (B). (See Figure 9)

9. Slide two 1/2” spacers (M) in between shelf bracket (C) and main bracket (B). (See Figure 9)

10. Use two 1/4-20 x 7/16” button head cap screws (N) and two large washers (F) to secure shelf bracket (C) to main bracket (B). (See Figure 9)

(rear view)

(C)

(B)

(M) x 2

(A)

(K)

(E)

(Below Cart/Ceiling Maximum)

(K)

(A)

(E)

(B)

(N) x 2

Figure 9

(F) x 2

Figure 10

Page 9

Installation Instructions FCA803/813

Above Installation

Assembling Shelf to Upright Bracket

1. Install two 1/4-20 x 1/2” button head cap screws (J) into lowest holes on upright bracket (A). (See Figure 11) or (See Figure 12)

2. Hang shelf (E) onto two screws installed in Step 1. (See Figure 11) or (See Figure 12)

3. Secure upright bracket (A) to shelf (E) using:

• 1/4-20 x 1/4” button head cap screw (H) if

installing to wall mount. (See Figure 11)

• 1/4-20 x 1/2” button head cap screw (J) if

installing to cart/ceiling mount. (See Figure 12)

4. Tighten all three screws to ensure shelf is secure.

(Above Wall)

(FCA813 shown)

(H)

(J) x 2

Attaching Shelf to Wall Mount

1. Use two 1/4-20 x 1/4” button head cap screws (H) and two large washers (F) to secure shelf bracket (C) to main bracket (B). (See Figure 13)

CAUTION: Slide bracket with caution so that the bracket

does not scratch or damage the wall!

2. Slide main bracket (B) behind wall mount rails until shelf bracket (C) rests on top wall mount rail. (See Figure 13)

(Above wall - all)

wall mount rails

(H) x 2

(F) x 2

(B)

(C)

(A)

(Above Cart/ceiling)

(FCA813 shown)

(J)

(A)

Figure 11

(J) x 2

Figure 13

3. Slide second shelf bracket (C) underneath lower rail on wall mount, lining up holes on shelf bracket (C) to holes on main bracket (B). (See Figure 14)

4. Use two 1/4-20 x 1/4” button head cap screws (H) and two large washers (F) to secure shelf bracket (C) to main bracket (B). (See Figure 14)

(Above wall - all)

(B)

(H) x 2

Figure 12

(C)

(F) x 2

Figure 14

Page 10

FCA803/813 Installation Instructions

NOTE: Refer to Table 3 and dimension drawings on pages 3-

4 to determine the extension level based on extension distance from mount center.

Table 3: Above Wall Mount

Extension distance from center of

NOTE: Minimum and maximum configurations are shown

5. Use 1/4-20 x 5/8” hex head flange bolt (K) and center washer (E) to secure upright bracket (A) to main bracket (B). (See Figure 15)

(Below wall - minimum)

mount (in.)

13.0-15.0 Minimum (FCA803)

15.0-17.5 Intermediate (FCA803)

17.5-19.0 Maximum (FCA803)

20.6-22.3 Minimum (FCA813)

22.3-27.9 Intermediate (FCA813)

27.9-29.4 Maximum (FCA813)

below. Intermediate configuration is the same.

(FCA813 shown)

(E)

(B)

Attaching Shelf to Cart/Ceiling Mount

IMPORTANT ! : If installing to a 2x1 display cart using

the FCA623 accessory, proceed to “Installing to FCA623 Accessory” Section (Step 6).

1. Use two 1/4-20 x 1/4” button head cap screws (H) and two large washers (F) to secure shelf bracket (C) to main bracket (B). (See Figure 16)

2. Slide main bracket (B) onto front of cart/ceiling mount head assembly until shelf bracket (C) rests on top of head assembly. (See Figure 16)

(Above cart/ceiling - Standard)

(rear view)

(F) x 2

(H) x 2

(C)

(B)

(K)

(A)

(Below wall - maximum)

(K)

(E)

(A)

(B)

Figure 16

3. Slide second shelf bracket (C) underneath head assembly, lining up holes on shelf bracket (C) to holes on main bracket (B). (See Figure 17)

4. Use two 1/4-20 x 1/4” button head cap screws (H) and two large washers (F) to secure shelf bracket (C) to main bracket (B). (See Figure 17)

(Above cart/ceiling - Standard) (rear view)

(B)

(H) x 2

(F) x 2

(C)

Figure 17

5. Proceed to Step 11.

Figure 15

Page 11

Installation Instructions FCA803/813

Installing to FCA623 Accessory

NOTE: Steps 6-10 only apply if installing to FCA623

accessory.

6. Use two 1/4-20 x 7/16” button head cap screws (N), two large washers (F) and two 1/2” spacers (M) to secure shelf bracket (C) to main bracket (B). (See Figure 18)

7. Slide main bracket (B) onto front of cart mount head assembly until shelf bracket (C) rests on top of head assembly. (See Figure 18)

(Above cart with FCA accessory) (rear view)

(F) x 2

(N) x 2

(M) x 2

(C)

(B)

Figure 18

8. Slide second shelf bracket (C) underneath head assembly, lining up holes on shelf bracket (C) to holes on main bracket (B). (See Figure 19)

9. Slide two 1/2” spacers (M) in between shelf bracket (C) and main bracket (B). (See Figure 19)

10. Use two 1/4-20 x 1/2” button head cap screws (J) and two large washers (F) to secure shelf bracket (C) to main bracket (B). (See Figure 19)

(Above cart with FCA623 accessory) (rear view)

Table 4: Above Cart/Ceiling

Extension distance from center of

mount (in.)

12.2-14.2 Minimum (FCA803)

14.2-16.7 Intermediate (FCA803)

16.7-19.2 Maximum (FCA803)

22.7-24.2 Minimum (FCA813)

24.2-28.0 Intermediate (FCA813)

28.0-31.0 Maximum (FCA813)

NOTE: Maximum and minimum configurations are shown

below. Several intermediate configurations are possible depending on which holes are used.

11. Use 1/4-20 x 5/8” hex head flange bolt (K) and center washer (E) to secure upright bracket (A) to main bracket (B). (See Figure 20) or (See Figure 21)

12. (For maximum/intermediate extension ONLY) Use two 1/4-20 x 1/2" button head cap screws (J) to secure upright bracket (A) to main bracket (B). (See Figure 20)

(Above cart/ceiling

- maximum/intermediate) (rear view)

(FCA813 shown)

(K)

(A)

(E)

(J) x 2

(B)

(J) x 2

(F) x 2

(M) x 2

(C)

Figure 19

NOTE: Refer to Table 4 and dimension drawings on pages 3-

4 to determine the extension level based on extension distance from mount center.

Figure 20

(Above cart/ceiling - minimum) (rear view)

(FCA813 shown)

(A)

(K)

(E)

Figure 21

(B)

Page 12

FCA803/813 Installation Instructions

Height Adjustment

1. Loosen hardware used to attach main bracket (B) to upright bracket (A). (See Figure 22)

2. Adjust shelf height as desired. (See Figure 22)

NOTE: For all above display installations, it is recommended

that the shelf be positioned so that it rests on top of display to help ensure an even mount.

3. Tighten hardware used to attached main bracket (B) to upright bracket (A). (See Figure 22)

(Above Cart/Ceiling shown as example)

(FCA813 shown)

Camera (example not included)

(FCA813 shown)

(Q)

Figure 22

Installing Camera (not included)

WARNING: Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight mounted on the

NOTE: Screw mounting options will vary based upon camera

model.

1. Install 1/4-20 x 3/8” Phillips pan machine screw (L) through mounting slot on shelf and into hole on bottom of camera. (See Figure 23)

2. Route cable from camera towards back of shelf and down behind the FCA803/813. (See Figure 23)

FCA803/813 does not exceed 2 lbs (0.9 kg)

Figure 23

Page 13

Installation Instructions FCA803/813

Page 14

FCA803/813 Installation Instructions

Page 15

Installation Instructions FCA803/813

Page 16

FCA803/813 Installation Instructions

Chief, a products division of Milestone AV Technologies

8800-003090 Rev00 2018 Milestone AV Technologies

www.milestone.com

10/18

USA/International A 6436 City West Parkway, Eden Prairie, MN 55344

P 800.582.6480 / 952.225.6000 F 877.894.6918 / 952.894.6918

Europe A Franklinstraat 14, 6003 DK Weert, Netherlands

P +31 (0) 495 580 852 F +31 (0) 495 580 845

Asia Pacific A Office No. 918 on 9/F, Shatin Galleria

18-24 Shan Mei Street

Fotan, Shatin, Hong Kong

P 852 2145 4099 F 852 2145 4477