CHIEF F-Series User Manual

Page 1
INSTALLATION INSTRUCTIONS
Small Flat Panel Mounts Model: F-Series
This Instruction Manual covers most of the F-Series wall and desk mounts, as well as selected F-Series pole mounts. NOTE: Some F-Series mounts (e.g., Table, Pole) and F-
Series accessories have sep arate Instruction Manuals.
See Specifications on page 3 for a complete list of models covered by this Instruction Manual .
IMPORTAN T ! : If an accessory such as an optional laptop tray is being installed, complete all required installation procedures within this document prior to installing the accessory.
F-Series Mounts (Examples)
Chief Manufacturing, a products division of
Milestone AV Technologies
6436 City West Parkway, Eden Prairie, MN 55344
• P: 800.582.6480 / 952.225-6000 • F:877.894.6918 / 952.894.6918
8800-002339 Rev00
©2013 Milestone AV Te chnologies, a
Duchossois Group Company
04/13
Page 2
Model: F-Series Installation Instructions
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the in formation cont ai ned her ein. Mil estone assu mes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief® is a regist ered t rademark of Mil estone AV Technol ogies . All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the corresponding instructions.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a ser vice cen ter fo r examination and repair.
WARNING: Do not use this product outdoors.
--SAVE THESE INSTRUCTIONS--
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury, damage to equipment, or voidi ng of f actory wa rrant y! It i s the installer’s responsibility to make sure all components are properly assembl ed and installed using the instructions provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five t imes t he combi ned wei ght of al l eq uip ment. Reinforce the structure as required before installing the component. The wall to which the mount is being attached may have a maximum drywall thickness of 5/8" (1.6cm). Do not install drywall anchors into the seam between drywall pieces.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the installer’s responsibility to make s ure the combined weight of all components located between the F-Series mount up to (and including) the display does not exceed the weight limit listed in Table 1.
2
Page 3
Installation Instructions Model: F-Series
CONTENTS
TOOLS REQUIRED FOR INSTALLATION...............................................................................................................3
SPECIFICATIONS....................................................................................................................................................3
MOUNT INSTALLATION...........................................................................................................................................4
DISPLAY INSTALLATION.................. .......... ................... ................... ......... ................... ................... ......... ...............7
ARRAY ASSEMBLY (DUAL / TRIPLE DISPLAY; FMA-220/-320 ONLY)................................................................10
MULTI-DUAL ARM ASSEMBLY (FCY- 210/-220 ONLY) ........ ................... ......... ................... ................... ......... .......1 1
CABLE MANAGEMENT .........................................................................................................................................13
ADJUSTMENT........................................................................................................................................................14
TOOLS REQUIRED FOR INSTALLATION
Phillips Screwdriver, #1 and #2
7/16" Wrench
Drill (All Wall Mount s)
1/8" Drill Bit (All Wall Mounts)
2.5mm Hex Key (approximately 3/32"; provided with Desk Mounts)
5/32" Hex Key (provided with applicable F-Series mounts)
3/16" Hex Key (provided with all F-Series mounts)
NOTE: Other tools may be required depending on your me thod of installation.
SPECIFICATIONS
Table 1: Mounts
MODEL NO. OF
DISPLAYS
TRAYS
FWP-1 10 Single Wall None No None 2.9 40 FWV-110 Single Wall Single Yes 13 2.2 25 FWS-1 10 Single Wall Single No 9.5 2.2 40 FWG-1 10 Single Wall Dual Yes 19. 5 2.2 25 FWD-1 10 Single Wall Dual No 16 2.2 40 FWB-1 10 Single Wall Triple Yes 26 2.2 25
FCV-110 Single Desk Single Yes 13.5 2.2 25
FCS-1 10 Single Desk Single No 10 2.2 40
FCG-1 10 Single Desk Dual Yes 20 2.2 25
FCD-110 Single Desk Dual No 16. 5 2.2 40 FCB-1 10 Single Desk Triple Yes 26.5 2.2 25
FPP-110 Single Pole None No None 2.2 40 FPS-110 Single Pole Single No 9.5 2.2 40
FPD-1 10 Single Pole Dual No 16 2.2 40
FGL-1 10 Tray Desk Single Yes 29.5 14 18 FGL-220 Single/Tray Desk Dual Yes 19.5 14 40 total FCY-210 Dual Desk Multi-Dual Yes (one arm) 20 2.2 40 FCY-220 Dual Desk Multi-Dual Yes (two arms) 20 2.2 40
SUPPORTING
STRUCTURE
NO. OF
MOUNTING
ARMS
ADJUSTABLE
HEIGHT
MAX.
EXTENSION
(INCHES)
MIN.
CLOSED
DEPTH
(INCHES)
MAX.
SUPPORT
WEIGHT
(LBS.)
3
Page 4
Model: F-Series Installation Instructions
MOUNT INSTALLATION
INSTALLATION TO WALL
1. Verify that you have the following parts:
Item Description Qty
10 MOUNT, Wall, F-Series 1 20 BRACKET, Wall 1 30 SCREW, Hex Head Lag, 1/4" x 2-1/2" 2 40 WASHER, Flat Machine Screw, 1/4" 2
2. Determine location for mount keeping in mind display size, extension, height adjustment (if applicable), and pitch/roll requirements. Bracket (20) MUST be installed into wood stud.
3. Using bracket (20) as a template, drill two 1/8" diameter pilot holes through top and bottom holes of bracket (20) into wall structure (See Figure 1).
10
20
20
40
30
Figure 1: Install Wall Bracket
4. Using 7/16" wrench, install screws (30) through washers (40), bracket (20), and drywall into wood stud (See Figure 1). Ensure bra cket (20) is vertical, then tighten screws (30).
IMPORTANT ! : Overtightening screws (30) may cause bracket (20) to compress into soft wall surface, resulting in difficult mount installation or improper engaging of set screw in step 6.
IMPORTANT ! : IF you will be installing a SINGLE display with RECESSED mounting holes, then proceed to "DISPLAY INSTALLA TION" before continuing with this mount installation procedure.
5. Insert top of mount (10) over lip on top of bracket (20) (See Figure 2). Swing mount (10) down flush against wall.
NOTE: FWS-110 shown; other wall mounts similar.
Figure 2: Install Wall Mount
6. Tighten set screw using 5/32" hex key (See Figure 3). Ensure set screw engages back side of bracket (20) to properly secure mount.
20
Set Screw
NOTE: FWS-110 shown; other wall mounts similar.
Figure 3: Tighten Set Screw
7. Proceed to "CABLE MANAGEMENT" (for SINGLE display with RECESSED mounting holes), or to "DISPLAY INSTALLATION" (for all other display configurations).
4
Page 5
Installation Instructions Model: F-Series
INSTALLATION TO DESK
Two installation options exist:
Edge Installation
Hole (Grommet) Installation; requires 3/8" to 3" diameter hole and access to the bottom of the desk
ASSEMBLY
Clamp Adjustment Screw
1. Verify that you have the following parts:
Item Description Qty
10 MOUNT, Desk, F-Series 1 20 BRACKET, Grommet 1 30 SCREW, Button Head Cap, 5/16"-18 x 4" 1 40 BUMPER, Adhesive 6
2. Determine approximate location for mount keeping in mind display size, extension, height adjustment (if applicable), and pitch/roll requirements.
3. Peel backing from adhesive bumpers (40) and attach to bottom of mount (10) (See Fig ure 4).
NOTE: One extra bumper (40) included for convenience.
40 (5 places)
10
Edge
of Desk
Clamp
Figure 5: Desk Mount - Edge Installation
2. If you are installing:
SINGLE display with RECESSED mounting holes: Pro ceed to "CABLE MANAGEMENT."
FCY-210/-220: Proceed to "MULTI-DUAL ARM ASSEMBLY."
ALL other display configurations: Proceed to "DISPLAY INSTALLATION."
HOLE (GROM MET) INSTALLATION
1. Using 2.5mm hex key, remove and retain baseplate and three attach screws from bottom of mount (10) (See Figure 6).
10
Figure 4: Install Bumpers
EDGE INSTALLATION IMPORTANT ! : IF you will be installing a SINGLE
display (including FCY-210/-220) with RECESSED mounting holes, then proceed to "DISPLAY INSTALLATION" before continuing with this mount installation procedure.
NOTE: Bracket (20) and screw (30) are not used in th is
installation.
1. Slip mount (10) over edge of desk so that clamp fully contacts desk edge. Using 3/16" hex key, securely tighten clamp adjustment screw (See Figure 5).
Attach Screws (3 places)
Baseplate
Baseplate
Nut
10
Figure 6: Baseplate
2. Using 3/16" hex key, remove clamp adjustment screw, washer, and clamp (See Figure 7). Retain clamp adjustment screw and washer for later use.
NOTE: Clamp will not be used for Hole (Grommet)
Installation.
5
Page 6
Model: F-Series Installation Instructions
5. Center mount (10) over hole. Using 3/16" hex key, securely tighten screw.
Clamp Adjustment Screw
Washer
10
Clamp
Figure 7: Remove Clamp Adjustment Scr ew
3. Using 2.5mm hex key, re-install baseplate with three retained attach screws. Ensure baseplate nut fac es interior of mount (See Figure 6). Tighten securely.
IMPORTANT ! : IF you will be installing a SINGLE display (including FCY-210/-220) with RECESSED mounting holes, then proceed to "DISPLAY INSTALLATION" before continuing with this mount installation procedure.
6. Drop screw (30) into open (unused) clamp adjustment hole on top of mount (for appearance only).
7. If you are installing:
SINGLE display with RECESSED mounting
holes: Pro ceed to "CABLE MANAGEMENT."
FCY-210/-220: Proceed to "MULTI-DUAL ARM
ASSEMBLY."
ALL other display configurations: Proceed to
"DISPLAY INSTALLATION."
INSTALLATION TO POLE
1. Verify that you have the following parts:
Item Description Qty
10 MOUNT, Pole, F-Series 1 20 CLA MP, Back 1 30 SCREW, Button Head Cap, 1/4"-20 x 1-1/8" 3
IMPORTANT ! : IF you will be installing a SINGLE display with RECESSED mounting holes, then proceed to "DISPLAY INSTALLA T ION"before continuing with this mount installation procedure.
2. Determine approximate location for mount keeping in mind display size, extension, height adjustment (if applicable), and pitch/roll requirements.
4. From below desk, insert retained clamp adjustment screw and washer through bracket (20) and up through hole in desk (See Figure 8) . Usin g 3/16" hex key, thread screw into baseplate nut but do not tighten completely at this time.
Baseplate Nut
Desk
20
Washer
Clamp Adjustment Screw
3. Place mount (10) against pole, with clamp (20) on opposite side of pole (See Figure 9). Using 5/32" hex key, loosely assemble with screws (30).
Pole
10
30 (3 places)
20
Figure 9: Pole Mount Installation
4. Position mount at desired height and orientation. Tighten screws (30) securely.
5. Proceed to "CABLE MANAGEMENT" (for SINGLE display with RECESSED mounting holes), or to "DISPLAY INSTALLATION" (for all other display configurations).
Figure 8: Desk Mount - Hole Installation
6
Page 7
Installation Instructions Model: F-Series
DISPLAY INSTALLATION
SINGLE D ISPLAY AND FCY-210/-220
NOTE: If you are installing DUAL / TRIPLE displays
FMA-220/-320, then proceed to page 9.
The mounting holes on the back of your display will either be flush with the back surface, or reces sed into the back surface. Refer to the ap plicable installation procedure.
FLUSH MOUNTING HOLES
1. Verify that you have the following parts:
Item Description Qty
10 MOUNT, F-Series 1 20 SCREW, Phillips Pan Machine, M4 x 12mm 4
CAUTION: Using screws of improper size may damage your display! Proper screws will easily and completely thread into display mounting holes.
CAUTION: Inadequate thread engagement in display may cause display to fall! Back out screws ONLY as necessary to allow installation of Centris b racket!
2. Ensure Centris bracket is able to swivel and tilt easily, yet still be tight enough to hold display in desired position. Adjust as required before proceeding. See "ADJUSTMENT" for detail.
3. Using Phillips screwdriver, carefully install two screws (20) into the upper mounting holes on the display. Thread screws completely into display, then back out 3 complete turns.
4. Pick up and align display so that screws (20) (installed on the back of the display in the previous step) fit into the mounting holes on the Centris bracket; rotate the bracket as required (See Figure 10). Lower the display firmly into place.
5. Using Phillips screwdriver, install two remaining screws (20) through the lower mounting holes in Centris bracket into the display.
6. Tighten all four screws (20). Do not overtight en!
7. FCY-210/-220 Only: Repeat Steps 1-6 for second display.
8. Proceed to "CABLE MANAGEMENT."
RECESSED MOUNTING HOLES
1. Verify that you have the following parts:
Item Description Qty
10 MOUNT, F-Series 1 20 SCREW, Phillips Pan Machine, M4 x 20mm 4 30 SCREW, Phillips Pan Machine, M4 x 30mm 4 40 SPACER, Nylon, 3/8" long 4 50 SPACER, Nylon, 3/4" long 4
2. Ensure Centris bracket is able to swivel and tilt easily, yet still be tight enough to hold display in desired position. Adjust as required before proceeding. See "ADJUSTMENT" for detail.
3. Carefully place display face down on protective surface.
4. Determine depth of recessed mounting holes relative to back surface of display (against which Centris head will contact).
5. Select proper length spacer and screw from table below:
NOTE: All spacers used should be the same length. If
the recess depths result in multiple spacer lengths, then select the longer spacer.
IF recess DEPTH is: THEN use spacer: AND screw:
3/8" or less 40 (3/8" long) 20 (M4 x 20mm) More than 3/8" up to
and including 3/4"
50 (3/4" long) 30 (M4 x 30mm)
20 (2 places)
Centris Bracket
Figure 10: Single Display - Flush Mount
10
6. Place the four selected spacers o ve r each of the mount holes on the back of the display.
7. Pick up and orient the mount (10) so that the mounting holes in the Centris bracket are aligned with the holes in the spacers; rotate the bracket as required (See Figure 11).
7
Page 8
Model: F-Series Installation Instructions
Centris Bracket
Figure 11: Single Display - Recessed Mount
CAUTION: Using screws of improper size may
damage your display! Proper screws will easily and completely thread into display mounting holes.
8. Using Phillips screwdriver, install four selected screws through the mounting holes in Centris bracket, through the spacers, into the display (See Figure 11). Tighten all four screws. Do not overtighten!
10
20 or 30 (4 places)
40 or 50 (4 places)
9. FCY-210/-220 Only: Repeat Steps 1-6 for seco nd display.
10. Continue with "MOUNT INSTALLATION."
8
Page 9
Installation Instructions Model: F-Series
DUAL / TRIPLE DISPLAY (FMA-220/-320 and KGL-22 0 ONLY)
The mounting holes on the rear of your display will either be flush with the rear surface, or recessed into the rear surface. Refer to the ap plicable installation procedure.
FLUSH MOUNTING HOLES
1. Verify that you have the following parts:
Item Description Qty
10 CENTRIS HEAD, Dual Knob Assembly 2-3 20 SCREW, Phillips Pan Machine, M4 x 12mm 4 per head
2. Carefully place display face do wn on protective
surface.
3. Place the Centris head (dual knob assembly) onto the
back of the display, aligning the mounting holes on the Centris bracket with the mounting holes on the display.
CAUTION: Using screws of improper size may damage your display! Proper screws will easily and completely thread into display mounting holes.
4. Using Phillips screwdriver, install four screws (20)
through the mounting holes in Centris bracket into the display (See Figure 12). Tighten all four screws (20). Do not overtighten!
Item Description Qty
20 SCREW, Phillips Pan Machine, M4 x 20mm 4 per head 30 SCREW, Phillips Pan Machine, M4 x 30mm 4 per head 40 SPACER, Nylon, 3/8" long 4 per head 50 SPACER, Nylon, 3/4" long 4 per head
2. Carefully place display face down on protective surface.
3. Determine depth of recessed mounting holes relative to back surface of display (against which Centris head dual knob assembly will contact).
4. Select proper length spacer and screw from table below:
NOTE: All spacers used should be the same length. If
the recess depths result in multiple spacer lengths, then select the longer spacer.
IF recess DEPTH is: THEN use spacer: AND screw:
3/8" or less 40 (3/8" long) 20 (M4 x 20mm) More than 3/8" up to
and including 3/4"
50 (3/4" long) 30 (M4 x 30mm)
5. Place the four selected spacers o ve r each of the mount holes on the back of the display.
6. Place the Centris head (dual knob assembly) onto the spacers, aligning the mounting holes on the Centris bracket with the holes in the spacers (See Figure 13).
10
Centris
20 (4 places)
Bracket
Figure 12: Dual / Triple Display - Flush Mount
5. Proceed to "ARRAY ASSEMBLY."
RECESSED MOUNTING HOLES
1. Verify that you have the following parts:
Item Description Qty
10 CENTRIS HEAD, Dual Knob Assembly 2-3
10
Centris Bracket
20 or 30 (4 places)
40 or 50 (4 places)
Figure 13: Dual / Triple Display - Recessed Mount
CAUTION: Using screws of improper size may
damage your display! Proper screws will easily and completely thread into display mounting holes.
7. Using Phillips screwdriver, install four selected screws through the mounting holes in Centris bracket, through the spacers, into the display (See Figure 13). Tighten all four screws. Do not overtighten!
8. Proceed to "ARRAY ASSEMBLY."
9
Page 10
Model: F-Series Installation Instructions
ARRAY ASSEMBLY (DUAL / TRIPLE DISPLAY; FMA-220/-320 ONLY)
1. Verify that you have the following parts:
Item Description Qty
10 ARRAY 1 20 SCREW, Button Head Cap, 5/16"-18 x 4"
(Used for Pivot / Swing Arm)
30 SCREW, Button Head Cap, 5/16"-18 x 5"
(Used with Height Adjustable Arm) 40 WASHER, 5/16", UHMW (plastic) 1 50 WASHER, 5/16", Stainless Steel 2 60 PIN 1 70 SPACER, UHMW (plastic) 1 80 NUT, Nylok, 5/16"-18 1 90 SCREW, Button Head Cap,1/4"-20 x 1/2" 2 100 NUT, Square, Machine Screw, 1/4"-20 2
2. Install pin (60) and spacer (70) into upper mount arm bore (See Figure 14).
1
1
4. Insert and hold nut (80) into lower mount arm bore (See Figure 14).
5. Insert screw (20 or 30, as applicable) through washer (50), washer (40), washer (50), array (10), array/ mount arm assembly, and into nut (80) (See Figure
14). Tighten screw as required using 3/16" hex key.
6. Slide the Centris head (dual knob assembly) onto the array (10) (See Figure 15). Ensure both the top and the bottoms of the Centris head are engaged into the corresponding slots in the array (10).
10
Centris Head
(20 shown; 30 similar)
20 or 30
50 40
50
70
10
60
80
Figure 14: Assemble Array
3. Install array (10) onto pin (60) (See Figure 14).
NOTE: Dual display shown ; triple display similar.
Figure 15: Install Display
7. Position the displays as desired and tighten the Centris head knob closest to the array (10). See "ADJUSTMENT" for additional information.
8. Using 5/32" hex key, install screw (90) and nut (100) on each end of the array (10) to prevent displays from accidently sliding off (See Figure 16).
90
100
10
NOTE: Left side shown; right side similar
Figure 16: Install End Locks
9. Proceed to "CABLE MANAGEMENT."
Page 11
Installation Instructions Model: F-Series
MULTI-DUAL ARM ASSEMBLY (FCY-210/-220, and FGL-220 ONLY)
BASIC ASSEMBLY
1. Verify that you have the following parts:
Item Description Qty
10 ARM ASSEMBLY, F-Series 2 20 MOUNT, Desk, F-Series 1 30 SCREW, Button Head Cap, 5/16"-18 x 4" 2 40 WASHER, 5/16", UHMW (plastic) 2 50 WASHER, 5/16", Stainless Steel 4 60 PIN 2 70 SPACER, UHMW (plastic) 2 80 WASHER, Lock, External Tooth, 5/8" 4 90 NUT, Nylok, 5/16"-18 2
2. Insert pin (60) into Y-connector upper bore in mount (20) (See Figure 17).
5. While holding nut (90) in lower bore of Y-connector, insert screw (30) through washer (50), washer (40), washer (50), arm assembly (10), and Y-connector, into nut (90) (See Figure 17). Loosely install screw (30) using 3/16" hex key.
CAUTION: Improper positioning of arm assembly (10) may result in failure of mount and subsequent damage to displays. Do NOT position either arm assembly (10) in gray shaded area.
6. Position arm assembly (10) within UNSHADED area as shown (See Figure 18). Using 3/16" hex key, tighten screw (30) as required to maintain position.
DO NOT POSITION
EITHER ARM ASSEMBLY
IN GRAY SHADED AREA
1030 50 40 50
80 or
70
60
Y-connector
NOTE: All parts same for both sides.
NOTE: FCY-220
90
20 shown; FCY-210 similar.
Figure 17: Multi-Dual Arm Assembly
3. Install spacer (70) or washer (80), as desired, on pin (60) (See Figure 17).
ALLOWABLE
AREA
Figure 18: Allowable Arm A rea
7. Repeat Steps 2. through 6. for second mount arm assembly (10).
8. If desired, proceed to "MODIFICATION." Otherwise, proceed to:
"CABLE MANAGEMENT" (for display with
RECESSED moun ting holes), or to
"DISPLAY INSTALLATION" (for all other display
configurations).
NOTE: Spacer (70) will allow limited movement of arm
assembly (10) relative to Y-connector, dependent upon tension of screw (30). Washer (80) will lock arm assembly (10) to Y-connector. See "ADJUSTMENT" for detail.
4. Insert arm assembly (10) on pin (60) (See Figure 17).
11
Page 12
Model: F-Series Installation Instructions
MODIFICATION
If desired, each arm assembly (10) may be modified to prevent movement of the outer arm relative to the inner arm (without loosening the adjustment screw).
NOTE: Spacer (shipped configuration) will allow limited
movement of outer arm relative to inner arm, dependent upon tension of screw. Washer (80) will lock arms together. See "ADJUSTMENT" for detail.
1. Using 3/16" hex key, loosen screw until nut can be removed (See Figure 19). Retain nut. Screw and washers may remain in outer arm.
Screw & washers
Outer arm
Inner arm
spacer or
80
pin
nut
Figure 19: Multi-Dual Arm Modification
2. Lift outer arm from pin (with screw and washers) and place on protective surface.
3. Remove spacer from pin (See Figure 19).
4. Install washer (80) on pin (See Figure 19).
5. Re-install outer arm (with screw and washers) on pin (See Figure 19).
6. Insert and hold nut in lower bo re of inner arm (See Figure 19).
7. Tighten screw as required using 3/16" hex key (See Figure 19).
8. Proceed to "CABLE MANAGEMENT" (for display with RECESSED mounting holes), or to "DISPLAY INSTALLATION" (for all other display configurations).
12
Page 13
Installation Instructions Model: F-Series
CABLE MANAGEMENT
Item Description Qty
10 COVER, Arm 1 per arm 20 SCREW, Philli ps Flat Machine, 8-32 x 3/8" 2 per arm 30 WRENCH, Hex, 3/32" (provi ded) 1
1. Attach all cables to display.
2. Open the cable management bracket by sliding it
towards the edge of the arm (See F igure 20).
NOTE: If necessary, cable management bracket attach
screws may be loosened using hex key (30).
Attach Screws
4. Close cable management bracket by sliding it back towards the centerline of the arm (See Figure 20).
NOTE: If necessary, cable management bracket attach
screws may be tightened using hex key (30).
CAUTION: Ensure that adequate cable slack exists for movement of display, and that cables will not be pinched by installation of cover (10) or screws (20).
5. Carefully insert cables in cavity located in lower portion of mount arm (See Figure 22).
6. Using Phillips screwdriver, install cover (10) with two screws (20).
Cable Path (typical)
OPEN Position
CLOSED Position
View from Bottom
Figure 20: Height Adjustable Arm -
Cable Management Bracket
CAUTION: Ensure that adequate cable slack exists for
movement of display, and that cables will not be pinched when bracket is closed.
3. Carefully insert cables into bracket (See Figure 21).
Cable Management Bracket (in open position)
90
10
20
Figure 22: Static Arm - Cable P ath
NOTE: Installation is complete.
Cable Path (typical)
NOTE: Display not shown for clari ty.
Figure 21: Height Adjustable Arm - Cable Path
13
Page 14
Model: F-Series Installation Instructions
ADJUSTMENT
ARM
PIVOT / SWING
CAUTION: If washer (80) has been used to assemble
FCY-210/-220 arms, then forced movement of arms without loosening screw (30) will damage arm and/or Y­connector (See Figure 17)(See Figure 19).
1. Using 3/16" hex key, slightly loosen or tighten the adjustment screw(s) as necessary (See Figure 23).
Adjustment Screws
CENTRIS HEAD
SINGLE DISPLAY AND FCY-210/-220
1. If previously attached, disconnect cables from display, then remove display.
2. Using Phillips screwdriver, slightly loosen or tighten the adjustment screw as necessary (See Figure 25).
Adjustment Screw
Phillips Screwdriver
Figure 25: Single Display Adjustment
3. Install mount and then display cables. See "DISPLAY INSTALLA TION."
Figure 23: Pivot / Swing Arm Adjustment
HEIGHT ADJUSTABLE (IF APPLICABLE)
1. Using 5/32" hex key, slightly loosen or tighten the adjustment screw as necessary (See Figure 24).
If display settles on its own, then rotate
adjustment screw counterclockwise (towards the "+" symbol).
If display rises on its own, then rotate adjustment
screw clockwise (towards the "-" symbol).
NOTE: It may be necessary to raise or lower the height
adjustable arm to expose the adjustment screw.
Adjustment Screw
DUAL / TRIPLE DISPLAY (FMA-220/-320 ONLY)
1. LATERAL POSITION ON ARRAY:
Using your fingers, slightly loosen adjust ment knob "A" (See Figure 26).
Slide display to desired position.
Using your fingers, tighten adjustment knob "A".
B
A
Figure 26: Dual / Triple Display Adjustment
2. PITCH / YAW / ROLL:
Figure 24: Height Adjustable A rm Adjustment
14
Using your fingers, slightly loosen adjust ment knob "B" (See Figure 26).
Adjust display as desired.
Using your fingers, tighten adjustment knob "B".
Page 15
Installation Instructions Model: F-Series
15
Page 16
Model: F-Series Installation Instructions
16
Loading...