Page 1
I N S T A L L A T I O N I N S T R U C T I O N S
Menu Board Interface Kits
FCASFP
FMSIML
FMSITL
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
FCASFP / FMSIML / FMSITL
Dutch Product Description
French Product Description
Page 2
FCASFP / FMSIML / FMSITL Installation Instructions
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located on the accessory does not exceed
the weight capacity listed in Table 1.
Table 1: Weight Capacity
Maximum Weight Allowed
FCASFP
FMSIML
75 lbs (34.0 kg)
125 lbs (56.7 kg)
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
FMSITL
125 lbs (56.7 kg)
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING: Do not use this product outdoors.
--SAVE THESE INSTRUCTIONS--
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all parts are properly
assembled and installed using the instructions provided.
WARNING: Failure to provide adequate structural strength
for this accessory can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which the mounting system is
attached can support five times the combined weight of all
equipment.
2
FCASFP..........................................................3
FMSIML..........................................................7
FMSITL.........................................................11
Page 3
Installation Instructions FCASFP / FMSIML / FMSITL
DIMENSIONS
FCASFP
12.50
317.5
FCASFP
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
DIMENSIONS: INCHES
[MILLIMETERS]
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
3
Page 4
FCASFP / FMSIML / FMSITL Installation Instructions
TOOLS REQUIRED FOR INSTALLATION - FCASFP
PARTS - FCASFP
DISPLAY ATTACH HARDWARE BAG
(Letters correspond to letters on bag)
A (4)
M4x12mm
E (4)
M5x20mm
I (4)
M6x25mm
M (4)
[Nesting spacer]
3/8"
B (4)
M4x20mm
F (4)
M5x25mm
J (4)
M8x12mm
C (4)
M4x25mm
G (4)
M6x12mm
K (4)
M8x20mm
N (4)
[Universal washer]
#2
D (4)
M5x12mm
H (4)
M6x20mm
L (4)
M8x30mm
R (1)
[Left interface bracket]
S (1)
[Right interface bracket]
Locking Hardware Kit
P (2)
10-24 x 5/8"
Q (2)
10-24
4
Page 5
Installation Instructions FCASFP / FMSIML / FMSITL
INSTALL INTERFACE BRACKETS TO
DISPLAYS
1. Raise the latch mechanism on both interface brackets (R
and S) to the OPEN position. (See Figure 1)
(S)
(R)
Latch
mechanism
already raised
LATCH OPEN
IMPORTANT ! : The M8 screws do NOT require a
washer. Use the universal washer (N) ONLY with M4, M5
and M6 screws.
• Proper screw length requires base of screw head
to protrude above flat washer a distance equal to
or greater than the screw diameter. If screw
length is inadequate, select longer screw. Select
shortest screw which will protrude the required
distance.
6. Align the center of the interface brackets (R and S) with
center of screen. (See Figure 2)
NOTE: The diamond-shape hole in the bracket corresponds to
the center of the mount.
7. Use selected screws (A-L), universal washers (N-if required)
and nesting spacers (M-if required), to connect interface
brackets (R and S) to back of display. (See Figure 2)
6
7
(A-L)
Center of
bracket
Latch
1
LATCH CLOSED
mechanism
Figure 1
2. Place displays face down on a soft, non-abrasive surface.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display. Properly sized
screws will easily and completely thread into display
mounting holes. If spacers are required, be sure to use longer
screws of the same diameter.
3. Select screw diameter by examining hardware (A-L) and
comparing with mounting holes on display. (See Figure 2)
4. Select spacers:
• Spacers are NOT required if mounting holes are
not recessed and interface brackets (R and S)
can lay flat against display.
• Nesting spacers (M) ARE required if mounting
holes are recessed, or if protrusions prevent
interface brackets (R and S) from laying flat.
5. Select screw length: (See Figure 2)
• By hand, insert SHORTEST length screw of
selected diameter (A, D, G or J) through universal
washer (N - if required), bracket (R or S), selected
spacer (M-if required), into display mounting hole.
Do NOT thread screw into hole at this time.
(N)
(MA or MB)
NOTE: Use universal washer (N) ONLY with M4, M5 and
M6 screws.
Figure 2
IMPORTANT ! : The M8 screws do NOT require a
washer. Use the universal washer (N) only with M4, M5
and M6 screws.
NOTE: The nesting spacers (M) may be used separately, or
put two together in different configurations to create
different size spacers. (See Figure 3)
(Single) (Nested) (Stacked)
0.375
[9.5]
0.563
[14.3]
0.750
[19.1]
Figure 3
5
Page 6
FCASFP / FMSIML / FMSITL Installation Instructions
ATTACH DISPLAYS TO MOUNTING RAIL
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! The displays must
be located approximately evenly across the length of the rail.
1. Ensure that the latch mechanisms on interface brackets (R
and S) are already raised to the OPEN position. (See
Figure 1)
CAUTION: BEFORE adding displays to the mounting rails,
ensure end caps (FMSECAP) are in place at BOTH ends of
mounting rail following instructions included with the
FMSECAP.
2. While supporting both sides of display, lower display onto
mounting rail, hooking top of interface brackets onto top of
mounting rail. (See Figure 4)
3. Lower the latch mechanism on both interface brackets to
lock bracket in place. (See Figure 4)
6. Adjust tilt as required. (See Figure 5)
7. The tilt may be locked at 0°, 10° and 20° using one
10-24 x 5/8" Phillips head screw (P) and one 10-24 lock nut
(Q) per interface bracket. (See Figure 5)
8. Tighten tilt friction bolt as necessary.
5
8
7
6
Tilt
friction
bolt
(P)
Lock at
20° tilt
(Q)
Lock at
10° tilt
2
Latch
mechanism
Figure 4
4. Repeat for remaining interface bracket.
Interface Bracket Adjustment
CAUTION: ALWAYS keep a small distance between
screens when making adjustments! Damage to screens
possible if placed too close together.
Lock at
0° tilt
(Displays not shown)
Figure 5
3
OPTIONAL: Security
1. OPTIONAL: Add padlock (not included) to each interface
bracket to lock display to mounting rail. (See Figure 6)
Padlock
(Optional)
Tilt
The interface brackets allow 0° to 20° tilt, and can be locked at
0°, 10° and 20° tilt.
5. If necessary, loosen button head tilt friction bolt (located on
side of interface bracket). (See Figure 5)
6
(Displays not shown)
Figure 6
Page 7
FCASFP / FMSIML / FMSITL Installation Instructions
2.54
1.59
AT MIDPOINT
DIMENSIONS
1.97
50.0
1.75
44.5
0.49
12.5
0.69
17.5
64.6
0.34
8.7
7.87
200.0
40.5
0.63
15.9
6.00
152.4
15.75
400.0
2.41
61.1
3.13
79.6
ADJUSTMENTS SHOWN
3/4" TOTAL
HEIGHT ADJUST
3/4" TOTAL
IN/OUT ADJUSTMENT
3/4" TOTAL
IN/OUT ADJUSTMENT
FMSIML
DIMENSIONS: INCHES
[MILLIMETERS]
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
FMSIML
7
Page 8
Installation Instructions FCASFP / FMSIML / FMSITL
TOOLS REQUIRED FOR INSTALLATION - FMSIML
PARTS - FMSIML
DISPLAY ATTACH HARDWARE BAG
(Letters correspond to letters on bag)
A (4)
M6 x 12mm
F (4)
M8 x 12mm
3/16"
B (4)
M6 x 16mm
G (4)
M8 x 16mm
#2
C (4)
M6 x 30mm
H (4)
M8 x 25mm
D (4)
1/4"
I (2)
1/4-20 x 1-1/4"
E (4)
.750x.344x.500
J (1)
[Right interface bracket]
K (1)
[Left interface bracket]
8
Page 9
Installation Instructions FCASFP / FMSIML / FMSITL
INSTALL INTERFACE BRACKETS TO
DISPLAYS
1. Place displays face down on a soft, non-abrasive surface.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display. Properly sized
screws will easily and completely thread into display
mounting holes. If spacers are required, be sure to use longer
screws of the same diameter.
2. Select screw diameter by examining hardware (A-C and
F-H) and comparing with mounting holes on display. (See
Figure 6)
3. Select spacers:
• Spacers are NOT required if mounting holes are
not recessed and interface brackets (J and K) can
lay flat against display.
• Spacers (E) ARE required if mounting holes are
recessed, or if protrusions prevent interface
brackets (J and K) from laying flat.
4. Select screw length: (See Figure 6)
• By hand, insert SHORTEST length screw of
selected diameter (A or F) through 1/4" washer
(D), bracket (J or K), selected spacer (E, if
required), into display mounting hole. Do NOT
thread screw into hole at this time.
• Proper screw length requires base of screw head
to protrude above flat washer a distance equal to
or greater than the screw diameter. If screw
length is inadequate, select longer screw. Select
shortest screw which will protrude the required
distance.
5. Align the center of the interface brackets (J and K) with
center of screen. (See Figure 6)
NOTE: The diamond-shape hole in the bracket corresponds to
the center of the mount.
6. Use selected screws (A-C or F-H), washers (D) and spacers
(E), if necessary, to connect interface brackets (J and K) to
back of display. (See Figure 6)
(D) x 4
(J)
(E) x 4, if required
5
Match diamond with
center of display
6
(A-C or F-H) x 4
(K)
Figure 6
9
Page 10
FCASFP / FMSIML / FMSITL Installation Instructions
ATTACH DISPLAYS TO MOUNTING RAIL
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! The displays must
be located approximately evenly across the length of the rail.
1. Ensure that the latch mechanisms on interface brackets (J
and K) are already raised to the OPEN position. (See
Figure 7)
CAUTION: BEFORE adding displays to the mounting rails,
ensure end caps (FMSECAP) are in place at BOTH ends of
mounting rail following instructions included with the
FMSECAP.
2. While supporting both sides of display, lower display onto
mounting rail, hooking top of interface brackets onto top of
mounting rail. (See Figure 7)
4
(I) x 2
Interface Bracket Adjustment
CAUTION: ALWAYS keep a small distance between
screens when making adjustments! Damage to screens
possible if placed too close together.
6. Move displays so that screens are nearly flush and level
with each other.
7. Use upper knob on back of interface brackets (J and K) to
adjust the height of each display. (See Figure 8)
NOTE: Adjust both brackets in order to maintain a level mount.
8. Use middle and lower knobs on back of interface brackets
(J and K) to make plumb adjustments to each display. (See
Figure 8)
7
7
(Display not shown for clarity)
8
1
NOTE: Secure
screw (I)
through both
holes.
Latch
CLOSED
3
Latch
OPEN
Figure 7
3. Raise latch on interface bracket and close into place against
mounting rail. (See Figure 7)
4. Fasten latch into place using one 1/4-20 x 1-1/4" socket
head screw (I). (See Figure 7)
NOTE: Socket head screws (I) must engage through both
holes to be fully secured. (See Figure 7)
5. Repeat for each interface bracket on the mounting rail.
8
Figure 8
10
Page 11
Installation Instructions FCASFP / FMSIML / FMSITL
1.83
DIMENSIONS
16.75
425.5
0.50
12.7
15.75
400.0
0.34
8.6
46.6
2.04
51.7
0.49
12.5
0.92
23.3
TYP.
7.87
200.0
2.10
53.4
14.23
361.6
4.05
103 .0
2.91
74.0
2.67
67.8
5.73
145.7
5.00
127.0
20°
HOLES FOR FIXING TILT
AT 0°, 10°, & 20°
HOLE FOR PADLOC K
DIMENSIONS: INCHES
[MILLIMETERS]
FMSITL
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
FMSITL
11
Page 12
Installation Instructions FCASFP / FMSIML / FMSITL
TOOLS REQUIRED FOR INSTALLATION - FMSITL
1/8" (included)
M5 (included)
PARTS - FMSITL
DISPLAY ATTACH HARDWARE BAG
(Letters correspond to letters on bag)
A (8)
M4x16mm
E (6)
M5x20mm
I (6)
M8x20mm
B (6)
M4x20mm
F (6)
M5x25mm
J (6)
M8x30mm
C (6)
M4x25mm
G (6)
M6x16mm
K (4)
M8x50mm
#2
D (6)
M5x16mm
H (6)
M6x25mm
3/8"
Q (2)
[Interface bracket]
R (1)
1/8"
S (2)
10-24
L (8)
.75x.323x.25"
M (8)
.75x.344x.5"
N (8)
[Univ. washer]
P (1)
M5
(In section
marked "N")
T (2)
10-24 x 5/8"
U (2)
10-24 x 2-1/4"
12
Page 13
Installation Instructions FCASFP / FMSIML / FMSITL
INSTALL INTERFACE BRACKETS TO
DISPLAYS
1. Lower the latch mechanism on each interface bracket (R).
(See Figure 9)
(Q)
1
Latch
mechanism
Figure 9
2. Place displays face down on a soft, non-abrasive surface.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display. Properly sized
screws will easily and completely thread into display
mounting holes. If spacers are required, be sure to use longer
screws of the same diameter.
NOTE: The diamond-shape hole in the bracket corresponds to
the vertical center of the mount.
Use selected screws (A-K), universal washers (N-if required)
7.
and spacers (L or M-if required), to connect interface
brackets (Q) to back of display. (See Figure 10)
6
(N)
(L or M)
(A-K)
Center of
bracket
(Q)
7
Figure 10
3. Select screw diameter by examining hardware (A-K) and
comparing with mounting holes on display. (See Figure 10)
4. Select spacers:
• Spacers are NOT required if mounting holes are
not recessed and interface brackets (Q) can lay
flat against display.
• Spacers (L or M) ARE required if mounting holes
are recessed, or if protrusions prevent interface
brackets (Q) from laying flat.
5. Select screw length: (See Figure 10)
• By hand, insert SHORTEST length screw of
selected diameter (A, D, G or I) through universal
washer (N - if required), bracket (Q), selected
spacer (L or M-if required), into display mounting
hole. Do NOT thread screw into hole at this time.
IMPORTANT ! : The M8 screws (I, J and K) do NOT
require a washer. Use the universal washer (N) ONLY
with M4 (A-C), M5 (D-F) and M6 (G and H) screws.
• Proper screw length requires base of screw head
to protrude above flat washer a distance equal to
or greater than the screw diameter. If screw
length is inadequate, select longer screw. Select
shortest screw which will protrude the required
distance.
6. Align the center of the interface brackets (Q) with center of
screen. (See Figure 10)
13
Page 14
FCASFP / FMSIML / FMSITL Installation Instructions
ATTACH DISPLAYS TO MOUNTING RAIL
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! The displays must
be located approximately evenly across the length of the rail.
1. Ensure that the latch mechanisms on interface brackets (Q)
are already lowered to OPEN position. (See Figure 11)
CAUTION: BEFORE adding displays to the mounting rails,
ensure end caps (FMSECAP) are in place at BOTH ends of
mounting rail following instructions included with the
FMSECAP.
2. While supporting both sides of display, lower display onto
one side of mounting rail, hooking top of interface brackets
onto front of mounting rail. (See Figure 11)
3. Raise the latch mechanism on both interface brackets to
lock bracket in place. (See Figure 11)
Figure 12
5
4
(T) x 2
2
3
3
Latch
mechanism
Figure 11
4. Fasten bracket against mounting rail using one 10-24 x 5/8"
button head cap screw (T). (See Figure 12)
5. Repeat for other interface bracket.
14
Page 15
Installation Instructions FCASFP / FMSIML / FMSITL
Interface Bracket Adjustment
CAUTION: ALWAYS keep a small distance between
screens when making adjustments! Damage to screens
possible if placed too close together.
Tilt
The interface brackets allow 0° to 20° tilt, and can be locked at
0°, 10° and 20° tilt.
1. If necessary, loosen button head tilt friction bolt (located on
side of interface bracket). (See Figure 13)
2. Adjust tilt as required. (See Figure 13)
3. The tilt may be locked at 0°, 10° and 20° using one
10-24 x 2-1/4" Phillips head screw (U) and one 10-24 lock
nut (S) per interface bracket. (See Figure 13)
4. Tighten tilt friction bolt as necessary.
1
OPTIONAL: Security
1. OPTIONAL: Add padlock (not included) to each interface
bracket to lock display to menu board. (See Figure 14)
Padlock
(Optional)
(Displays not shown)
Figure 14
3
Lock at
0° tilt
(U)
Tilt
friction
bolt
4
Lock at
20° tilt
(S)
Lock at
10° tilt
2
(Displays not shown)
Figure 13
15
Page 16
FCASFP / FMSIML / FMSITL Installation Instructions
Chief, a products division of
Milestone AV Technologies
8800-003032 Rev01
2018 Milestone AV Technologies
www.milestone.com
11/18
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000
F 877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852
F +31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
Loading...