Chief FCAV1U User Manual

Page 1
INSTALLATION INSTRUCTIONS
(Shown on LTM1U)
Fully extended
(Shown on LTM1U)
Fully retracted
Fusion Pull-Out Accessory
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
FCAV1U
Page 2
FCAV1U Installation Instructions
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
DEFINITIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the corresponding instructions.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! Adding the FCAV1U accessory may change the weight capacity listed for the mounting system. Consult (Table 1) for mounting system’s weight capacity details when attached to FCAV1U.
Table 1: Weight Capacity When Attached to FCAV1U
MODEL Maximum Weight Allowed
MTM1U
MSM1U
MTMP1U
LTM1U
LSM1U
XSM1U
XTM1U
125 lbs (56.7 kg)
125 lbs (56.7 kg)
125 lbs (56.7 kg) mounted to single 2"x4" wood stud
150 lbs (68.0 kg) mounted to double 2"x4" wood studs
150 lbs (68.0 kg)
150 lbs (68.0 kg)
150 lbs (68.0 kg)
150 lbs (68.0 kg)
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting system such as a video camera, CPU, screen, display, projector, etc.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all products are properly assembled and installed using the instructions provided.
WARNING : Use this accessory only for its intended use as
described in these instructions. Do not use attachments not recommended by the manufacturer.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! :
mounted to:
a bare 8" concrete or 8"x8"x16" concrete block wall, or
a 2" x 4" wood studs wall covered by drywall with maximum thickness of 5/8":
MSM1U/MTM1U/MTMP1U: Wood studs must be
The FCAV1U accessory is designed to be
16" on center;
LSM1U/LTM1U: Wood studs may be 16" or 24"
on center;
XSM1U/XTM1U: Wood studs may be 24" or 32"
on center.
NOTE: Accessory is intended to be used with the following
Chief mounting systems (not included):
•MTM1U
•MSM1U
•MTMP1U
•LTM1U
•LSM1U
•XTM1U
XSM1U
--SAVE THESE INSTRUCTIONS--
2
Page 3
Installation Instructions FCAV1U
17.50
444.5
FULL EXTENSION
AT 0° PLUMB
SCREW DRIVEN RETAINER
LATCH
1.56
39.7
19.50
495.3
FULL RETRACTION
AT 0° PLUMB
FCAV1U INCLUDES TWO ASSEMBLIES
DIMENSIONS: INCHES [MILLIMETERS]
0.5°
MAX DOWN
PLUMB
1.56
39.7
AT 0°
MAX UP
PLUMB
A
DETAIL A
SCALE 1 : 2
DIMENSIONS: INCHES [MILLIMETERS]
DIMENSIONS
3
Page 4
FCAV1U Installation Instructions
3.00
76.2
FULL EXTENSION
AT 0° PLUMB
WITH LTM1U
3.57
90.7
SHOWN WITH LATERAL SHIFT
ON CENTER
DIMENSIONS: INCHES [MILLIMETERS]
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
DIMENSIONS -- continued
LEGEND
4
Page 5
Installation Instructions FCAV1U
1/2"
1/2"
3/16" (included)
7/32" (5.5mm) Wood Stud 3/8" (9.5mm) Concrete
A (2) [Fusion pullout
Wall-Mounting Hardware Kit
B (4) 5/16 x 2-1/2"
C (4) [Fischer UX10x60R]
D (4) 5/16"
E (1) 3/16" x 10"
F (4) 1/4-20 x 1/2"
G (4) 5/16-18 x 1/2"
H (4) 1/4"
J (4) 5/16"
FCAV1U Hardware Kit
accessory]
TOOLS REQUIRED FOR INSTALLATION
PARTS
5
Page 6
FCAV1U Installation Instructions
Center of screen
8"
Vertical center of accessory
(203.2mm)
(front view)
(A)
1
3
4
NOTE: Hook tape
measure here or here
4
11
12
5
6
(D) x 2
7
10
(B) x 2
9
(D) x 2
13
(B) x 2
13
INSTALLATION
NOTE: The FCAV1U enables the mounting system to be
pulled out away from the wall for any servicing needs.
Locate Mounting Site
WARNING:
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installers responsibility to make certain the structure to which the accessory is being attached is capable of supporting five times the combined weight of accessory and mount,
capacities listed in Table 1 (See Table 1)
NOTE: Proceed to either the Installing to a Wood Stud Wall
section or the Installing to a Concrete Wall section.
Installing to a Wood Stud Wall
1. Determine the center of the TV screen, and where it should be located on the wall.
2. Locate the closest stud to the left and right of the selected location.
NOTE: If the screen area lies over a stud, use that stud and the
stud to either the left or right of it.
3. Line up the diamond cutouts on Fusion pullout (A) with center of screen marking to determine vertical center. (See Figure 1)
4. Measure up 8" (203.2mm) from the center point (by hooking tape measure in slots on front of FCAV1U) to mark location of the upper mounting slots.
IMPROPER INSTALLATION CAN LEAD TO
not to exceed weight
.
5. Using a level, mark the wall on each stud to attach the accessory through the upper mounting slots. (See Figure 2)
6. Drill one 7/32" (5.5mm) pilot hole in each stud.
NOTE: The slotted washers have been included to help make
the installation easier. Wait to place the slotted washer AFTER the Fusion pullouts are hanging on the partially installed lag bolts. (See Steps 7-10)
7. Partially install two 5/16 x 2-1/2" flanged lag bolts (B) into pilot holes but do not tighten to wall.
8. Hang both Fusion pullouts (A), aligning upper mounting slots over lag bolts and adjust side-to-side for proper location.
9. Place one slotted washer (D) over each flanged lag bolt. (See Figure 2)
10. Tighten lag bolts to secure accessory (A) to wall at upper mounting slots.
11. Mark the attachment points for the lower mounting slots, making sure the attachment points are located on the studs. (See Figure 2)
12. Drill 7/32" (5.5mm) pilot holes at markings for lower mounting holes. (See Figure 2)
13. Use two 5/16 x 2-1/2" flanged lag bolts (B) and two 5/16" slotted washers (D) to attach both pullouts (A) to the wall through the lower mounting holes. (See Figure 2)
14. Proceed to Attaching Mounting System section.
6
Figure 1
Figure 2
Page 7
Installation Instructions FCAV1U
11
5
6
4
12
x 4
(C) x 4
10
7
10
(B) x 2
(D) x 2
9
(D) x 2
13
13
(B) x 2
2
3
Mounting system (not included)
(F) x 4
(H) x 4
(J) x 4
(A)
(G) x 4
Installing to a Concrete Wall
1. Determine the center of the TV screen, and where it should be located on the wall.
2. Line up the notches on accessory (A) with center of screen marking to determine vertical center. (See Figure 1)
3. Measure up 8" (203.2mm) from the center point to mark location of the upper mounting slots. (See Figure 1)
4. Using a level, mark the wall through both upper mounting slots. (See Figure 3)
11. Mark the attachment points for the lower mounting slots, making sure the attachment points are located on the studs. (See Figure 3)
12. Drill 3/8" x 3-1/2" (9.5mm x 88.9mm) pilot holes at markings for lower mounting holes. (See Figure 3)
13. Use two 5/16 x 2-1/2" flanged lag bolts (B) and two 5/16" slotted washers (D) to attach the accessory to the wall through the lower mounting holes. (See Figure 3)
ATTACHING MOUNTING SYSTEM
1. Attach top of mounting system (not included) to top of FCAV1U accessories using two 5/16-18 x 1/2" button head cap screws (G) and two 5/16" washers (J) in each top mounting slot. (See Figure 4)
2. Attach bottom of mounting system to bottom of FCAV1U accessories using two 1/4-20 x 1/2" socket head cap screws (F) and two 1/4" washers (H) in each bottom mounting slot. (See Figure 4)
Figure 3
CAUTION: MINIMUM HORIZONTAL DISTANCE
BETWEEN WALL BRACKETS IS 16" (406.4mm). Do not place FCAV1U pullout accessories closer together than 16" (406.4mm).
5. Drill one 3/8" x 3-1/2" (9.5mm x 88.9mm) pilot hole at each marking.
6. Install an anchor (C) into each pilot hole using a hammer, making sure that the anchor is flush with the wall.
NOTE: The slotted washers have been included to help make
7. Partially install two 5/16 x 2-1/2" flanged lag bolts (B) into
8. Hang accessory (A), aligning upper mounting slots over lag
9. Place one slotted washer (D) over each flanged lag bolt.
10. Tighten lag bolts to secure accessory (A) to wall at upper
the installation easier. Wait to place the slotted washer AFTER the Fusion pullouts are hanging on the partially installed lag bolts. (See Steps 7-10)
pilot holes but do not tighten to wall.
bolts, and adjust side-to-side for proper location.
(See Figure 3)
mounting slots.
Figure 4
3. The remainder of the mounting system installation may be completed at this time, following the installation instructions included with the mounting system.
7
Page 8
FCAV1U Installation Instructions
1
1
Tighten retainer latch by turning
counterclockwise
Loosen retainer latch by turning
clockwise
2
3
4
5
ADJUSTMENTS
Moving Mount to Wall (Optional)
1. Close the FCAV1U brackets and tighten the retainer latch (turn counterclockwise) to hold the brackets in the retracted position. (See Figure 5)
IMPORTANT ! : Do NOT over-tighten the retainer latch.
Adjusting Mount Against Wall
IMPORTANT ! : Carefully adjust the mount plumb evenly
on both sides to avoid placing too much stress on the screen.
5. Adjust plumb of mount by turning the adjustment nut on the FCAV1U. (See Figure 6)
Figure 6
Figure 5
Moving Mount to Service Position
2. Loosen the retainer latch by turning screw clockwise. (See Figure 5)
3. Pull mount out from wall.
4. Return mount towards wall after service is complete.
8
Page 9
Installation Instructions FCAV1U
9
Page 10
FCAV1U Installation Instructions
10
Page 11
Installation Instructions FCAV1U
11
Page 12
FCAV1U Installation Instructions
Chief, a products division of Milestone AV Technologies
8800-002781 Rev00 2016 Milestone AV Technologies
www.chiefmfg.com
01/16
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000 F 877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852 F +31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099 F 852 2145 4477
Loading...