Chief CSSLP15X10 Users Guide

Page 1
I N S T A L L A T I O N I N S T R U C T I O N S
Sliding Storage Panel
Spanish Product Description German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
CSSLP15X10
Page 2
CSSLP15X10 Installation Instructions
WALL MOUNTING
PLATE/COMPONENT
MOUNTING SURFACE
DISCLAIMER
Legrand | AV and its affiliated corporations and subsidiaries (collectively “Legrand | AV”), intend to make this manual accurate and complete. However, Legrand | AV makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Legrand | AV makes no representation of warranty, expressed or implied, regarding the information contained herein. Legrand | AV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting system such as a video camera, CPU, screen, display, projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
damage or destruction of equipment if you do not follow the corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all accessories are properly assembled and installed using the instructions provided.
WARNING:
serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components attached to accessory does not exceed 15 lbs (6.8 kg).
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not recommended by the manufacturer.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and repair.
WARNING: Do not use this accessory outdoors.
Exceeding the weight capacity can result in
CAUTION: A CAUTION alerts you to the possibility of
DIMENSIONS
18.96
481.5
10.00
254.0
--SAVE THESE INSTRUCTIONS--
10.69
271.6
7.00
21.30
22.00
541.0
558.8
177.8
HOLES
6.5
0.26
2
Page 3
Installation Instructions CSSLP15X10
LEGEND
Tighten Fastener
Apretar elemento de fijación Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación Befestigungsteil lösen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis à pointe cruciforme
Pencil Mark
Marcar con lápiz Stiftmarkierung Marcar com lápis Segno a matita Potloodmerkteken Marquage au crayon
Drill Hole
Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou
Adjust
Ajustar Einstellen Ajustar Regolare Afstellen Ajuster
Open-Ended Wrench
Llave de boca Gabelschlüssel Chave de bocas Chiave a punte aperte Steeksleutel Clé à fourche
By Hand
A mano Von Hand Com a mão A mano Met de hand À la main
Hex-Head Wrench
Llave de cabeza hexagonal Sechskantschlüssel Chave de cabeça sextavada Chiave esagonale Zeskantsleutel Clé à tête hexagonale
Remove
Quitar Entfernen Remover Rimuovere Verwijderen Retirez
Optional
Opcional Optional Opcional Opzionale Optie En option
Security Wrench
Llave de seguridad Sicherheitsschlüssel Chave de segurança Chiave di sicurezza Veiligheidssleutel Clé de sécurité
3
Page 4
CSSLP15X10 Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
1/2"
#2
1/4"
PARTS
Installation Hardware Kit
A (4) [10-12 x 1" drywall anchor]
D (4) 5/16-18 x 3/8"
G (1) [CSSLP15X10 Storage Panel]
B (4) #10 x 1"
E (20) .625x.140x.031
C (2) [Slot nut]
F (2) [Rivet]
4
Page 5
Installation Instructions CSSLP15X10
INSTALLATION
NOTE: The storage panel (G) may be installed using either of two methods. Proceed to either Installing Storage Panel to Wall
section OR Installing Storage Panel to Extrusion section.
Installing Storage Panel to Wall
NOTE: The storage panel (G) may be installed directly on the wall in one of two horizontal positions or vertically below the display.
(See Figure 1) or (See Figure 2)
Horizontal Wall Mount - Right Horizontal Wall Mount - Left
The storage panel MUST be mounted with the clip located at the bottom.
(G)
Clip
Figure 1
Vertical Wall Mount - below
(G)
Clip
Figure 2
1. Determine location for the CSSLP15X10.
2. Using the CSSLP15X10 (G) as a template, mark the locations of four mounting holes. (See Figure 3)
5
Page 6
CSSLP15X10 Installation Instructions
3. Slide two slot nuts (C) into end of extrusion. (See Figure 5)
(G)
(horizontal shown)
(C x 2)
(C x 2)
2
4
(B) x 4
x 4
3
(A x 4)
Figure 3
3. Drill four 1/4" pilot holes and insert drywall anchors (A) at markings. (See Figure 3)
CAUTION: The storage panel must be mounted with the
clip at the bottom. (See Figure 1)
4. Fasten storage panel (G) to wall using four #10 x 1" Phillips pan wood screws (B). (See Figure 3)
Installing Storage Panel to Extrusion
NOTE: The storage panel may be located anywhere along the
extrusion. For ease of use, it may be more convenient to place it to the extreme left or right side of the extrusion.
1. Remove screws and end cap from extrusion. (See Figure 4)
2
2
(D x 4)
Figure 5
CAUTION: The storage panel must be mounted with the
clip at the bottom. (See Figure 1) and (See Figure 6)
4. Hold the storage panel (G) over the four button head screws (D) and lower the storage panel keyholes over the screws. (See Figure 6)
(D) x 4
Keyholes
5
4
1
x 2
End cap
Extrusion
Figure 4
2. Insert four 5/16-18 x 3/8" button head cap screws (D) into the two slot nuts (C) and partially tighten. (See Figure 5)
6
Clip
Figure 6
5. Tighten screws securely against the storage panel.
Page 7
Installation Instructions CSSLP15X10
Attaching Components
1. Remove mounting plate from storage panel by pressing
inward on the clip located at the bottom of the storage panel. (See Figure 7)
2. Place component(s) on mounting plate and position in the
desired location with the hole pattern in mounting plate best aligned to component mounting holes. (See Figure 7)
Component
(E)
Clip
1
Mounting plate
3
Component fasteners
Component Panel Usage
1. Gently push component panel in until it unlocks. (See Figure 9)
1
Figure 9
2. Pull component panel out away from display. (See Figure
10)
1
Figure 7
3. Using the fasteners provided with the component and the washers (E), attach the component to the mounting plate. (See Figure 7)
4. Return mounting plate to storage panel by installing the side without the clip into the panel first, followed by the side with the clip until it clicks into place. (See Figure 8)
5. OPTIONAL: If desired, install plastic rivet (F) into hole next to clip to secure the mounting plate in place.(See Figure 8)
Side without clip
Clip
5
OPTIONAL
Insert plastic rivet
Side with clip
Figure 8
2
2
4 4
Figure 10
3. Access components on panel as desired.
4. Push component panel back into place until it "clicks" back into its original position. (See Figure 10)
7
Page 8
CSSLP15X10 Installation Instructions
8800-003297 Rev00 2021 Legrand | AV
www.legrandav.com
04/2021
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000 F 877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852 F +31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099 F 852 2145 4477
Loading...