Chicony Electronics Co MSR0305T User Manual

A. FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device,
Pursuant to Part 15 the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, use s an d can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determine d by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.

WARNING:

Use only shielded cables to connect I/O devices to this equipment.
You are cautioned that changes or modifications not expressly approved by the party responsible
for compliance could void your authority to operate the equipment.

CAUTION: AVOID PROLONGED USE OF THE KEYBOARD WITHOUT BREAKS.
Take regular breaks and keep a good posture. Consult your physician promptly if you notice any
lost of motion or pain in your wrist when using the keyboard.

INFORMATION FOR OPTICAL POINTING DEVICES ONLY :

User-observable light is 15 microwatts in normal operation.
This product has been tested to comply with international Standard IEC 60825-1:(1993), incid.
Amd.2(2001). This product uses LEDs that are inherently Class 1.

Class 1 LED Product

B. PRODUCT SPECIFICATION

1. SYSTEM AND INTERFACE
Receiver Interface: USB interface designed to be fully compatible with Microsoft Windows 98,
ME, 2000, XP system.

2. HOT KEYS
Implements 17 hot keys to easy access as below function: Volume down, Mute, Volume up,
Previous track, Stop, Play, Next track, Wake up, Sleep, Shut down, Internet, Email, Search,
My favorite, Calculator, Backward, and Forward function.

3. FREQUENCY BAND :
Keyboard – 27.195 MHz
Mouse – 27.045 MHz

4. FREQUENCY MODULATION : FSK MODE

5. POWER RATING :
Keyboard: 3 V , 30 mA (MAX)_
Mouse: 3 V , 50 mA (MAX)_
Receiver: 5 V , 100mA (MAX) for USB

6. BATTERY:
Keyboard: 2 pieces of AA Batteries
Mouse: 2 pieces of AA Batteries

7. BATTERY LIFE TIME :
Keyboard: 500 hours reference (operating mode)
Mouse: 60 hours reference (operating mode)

8. OPERATION DISTANCE
Keyboard: 6 feet without signal disturbance and no direction limit.
Mouse: 5 feet without signal disturbance and no direction limit.

9. MOUSE DETECTION METHOD
Mouse: Mechanical tracking method (Roll ball optical sensor)

10. MOUSE RESOLUTION: 400 DPI

11. OPERATING TEMPERATURE : 0º C~ 40º C.
12 STORAGE TEMPERATURE : -10º C ~ 60º C.

C. HARDWARE INSTALLATION

1. Plug the receiver connector into an USB port.

2. SYSTEM will take around 10 sec to find your keyboard and mouse automatically.
(PS : If your OS is Windows® 98, please follow the screen instruction to complete your
keyboard and mouse installation)

3. Please keep your receiver from the other electrical devices about 8 inches. The other
electrical devices may influence your receiver sensitivity.

4. Put two batteries into your keyboard battery chamber, and another two batteries into
your mouse battery chamber.

D. BATTERY STATUS

1. There is one LED on the top of receiver. The LED will be blinking during the ID setting or data
received. The LED will be always ON, if the battery status of keyboard or mouse is low. Please
prepare one set of batteries in case of keyboard or mouse working abnormal.

E. ID CHANGE
Note: This is a single channel product. There is one individual channel for the key board and
another one channel for the mouse. Different ID still can keep your mouse or keyboard
working fine at the same channel, but please keep two sets of keyboard and mouse are not
close to 6 feet between each others.

Please press the button on the receiver. The LED will be twinkling slowly. Remove the battery and
press any key several times. Put the batteries back to the battery chamber, and then you will see
the LED of receiver will be twinkling fast momentarily. The device is working now.
The Keyboard and Mouse use the same way to change the ID.

Note: This is very important !! After you remove the battery, please press any key several