Chicony Electronics Co KR 0309 User Manual

A. FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT

This equipment has been tested and found to comply with the limits for a Class B
digital device, Pursuant to Part 15 the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.

WARNING:

Use only shielded cables to connect I/O devices to this equipment.
You are cautioned that changes or modifications not expressly approved by the
party responsible for compliance could void your authority to operate the
equipment.

CAUTION: AVOID PROLONGED USE OF THE KEYBOARD WITHOUT
BREAKS.
Take regular breaks and keep a good posture. Consult your physician promptly if
you notice any lost of motion or pain in your wrist when using the keyboard.

INFORMATION FOR OPTICAL POINTING DEVICES ONLY :

User-observable light is 15 micro-watts in normal operation.
This product has been tested to comply with international Standard IEC 60825­1:(1993), incid. Amd.2(2001). This product uses LEDs that are inherently Class 1.

Class 1 LED Product

Contents

Getting Started
Features
Preparing Keyboard, mouse and receiver
Hardware Installation

-- Connect the receiver
+--- USB Interface

-- Inserting batteries
+--- Inserting batteries into mouse
+--- Inserting batteries into keyboard

-- Setting frequency channel or ID
+--- Setting frequency channel on keyboard and mouse
+--- Setting ID on keyboard and mouse

Software Installation

-- Installing software for mouse

-- Installing software for keyboard
Displaying keyboard Modes
Working with keyboard and mouse

-- Using mouse wheel

-- Keyboard battery indicator

-- Writing using the keyboard

-- Cleaning the keyboard and the mouse
Product Specification
Troubleshooting and tips

Getting Started

Thank you for choosing this Wireless keyboard and Mouse Kits. It operates with
digital radio technology to ensure no hinder communication between the keyboard,
the mouse and your computer without connecting cable.
The transmission and receiving of keyboard and mouse are free from angle
restriction. There are two frequency channels each for keyboard and mouse to
prevent malfunctions when you operate several radio transmission devices
simultaneously.

Features
. Complies with Directive 1995/5/EC of the European Parliament and

Commission.

. Complies with the mutual recognition of conformity 1999 for radio and

telecommunications Equipment.

. Manufactured with environmental friendly recycled materials.
. Fully compliant with original USB version 1.0 and 1.1.

Preparing Keyboard, mouse and receiver Before working with your new keyboard and mouse, look at the “Hardware Installation” , and take a few one-time preparations.

Hardware Installation

Place the receiver at least 20 cm from other electrical devices (e.g. monitor) to
achieve optimum performance.
The distance between the keyboard, mouse and receiver should not exceed 5
feet. Do not place the receiver on metal surfaces.

Step 1: Connect the receiver

1. Plug the receiver connector into an USB port.

2. SYSTEM will take around 10 sec to find your keyboard and mouse
automatically. (PS : If your OS is Windows® 98, please follow the screen
instruction to complete your keyboard and mouse installation)

3. Please keep your receiver from the other electrical devices about 8 inches. The
other electrical devices may influence your receiver sensitivity.

4. Put two batteries into your keyboard battery chamber, and another two
batteries into your mouse battery chamber.

Setp 2: Insert batteries
. Inserting batteries in mouse

The mouse requires two alkaline batteries (AA or AAA).
(1) Please remove the battery compartment cover on the bottom of the mouse.
(2) Insert the two alkaline batteries (AA or AAA) in the battery compartment.
(3) Fix the battery compartment cover (1) on the bottom of mouse again

Dangerous!! Please only use batteries of the same type.