Page 1
WiFi Car DVR
User Manual
Page 2
Names of Parts
Lens
Tripod
Mount
LCD Panel
Power/Menu Button
Record Button
GPS Receiver Slot
Micro HDMI Port
Speaker
Mic
Status Indicator
Micro USB Port
microSD Card Slot
Emergency Button
English
| 1
Page 3
Getting Started
Inserting a microSD Card
Before initial use, insert a microSD card.
(suggested at least 4GB, up to 64GB)
Charging the Unit
Fully charge camcorder for initial use by:
• Car charger
• PC USB port
• USB adapter
During charging, screen shows battery icon or status indicator ashes in
orange
(not included)
. When camcorder is fully charged, the indicator turns off.
Shooting a Video
1. Power on:
Press to turn on camcorder.
2. Record:
Press to start recording.
Press again to stop.
3. Playback:
Press to enter menu settings.
Press to select [Playback ].
Press [Play ] to play the video and press [ ] to stop.
4. Return to preview:
Press [ ] to return.
5. Power off:
Press and hold for 2 seconds.
English
2 |
microSD card
Page 4
Camcorder Operation
Auto REC
60 SEC
OFF
In preview, press to enter menu settings
Button functions indicated by
to navigate menu settings and to back to preview .
Menu Settings
Camcorder has eight menu settings. Advanced settings can be set up via
mobile APP.
Menu Settings Descriptions
Playback
Action Cam
Dash Cam
WiFi - Local
WiFi - Cloud
Voice Record
Auto Record
Screen Auto Off
Settings
Note: After 10 seconds of non-operation in menu settings, screen
returns to preview.
Play recorded videos
Switch between Action Cam and Dash Cam
Enable/Disable WiFi for wireless connection
Enable/Disable internet cloud connection
Enable/Disable voice recording (Dash cam
mode only)
Enable/Disable
engine starts (Dash cam mode only)
Screen turns off after 60 seconds of non-
operation
Reset to factory default settings or format SD
card.
.
. Use
auto recording when car
(Dash cam mode only)
English
| 3
Page 5
Record Modes
Camcorder has two recording modes for different applications:
Action Cam: Shoot normal videos.
Dash Cam: Shoot loop and emergency videos.
Comparison between modes:
Mode Action Cam Dash Cam
Record type Normal Loop Emergency
Record trigger
Record duration
Display info
.
Note:
1. During loop recording, oldest les are overwritten if microSD card is full.
2. During loop recording, press to enable/disable mute fuction.
P
ress in preview
Unlimited
00:06:36
SD card remaining time Current date & time
Three min. sections
• Car impact
• Press during
loop recording
One min. section
(30 seconds before
and after the event)
2014/01/01 21:06:36
Transfer Files to PC:
1. Connect camcorder to PC via Micro USB cable.
2. Find video at "My computer\Removable Disk\".
3. Copy, move, delete, and playback videos on PC.
View Camcorder Screen on TV:
1. Connect camcorder to TV
2. Turn on camcorder.
3. Camcorder screen displays on TV simultaneously.
English
4 |
via
Micro HDMI cable (not included).
Page 6
Mobile Camcorder
Local
Wireless & APP Operation
Internet
AP
Unieye
Server
AP
3G/4G Mobile Hotspot
3G/4G Mobile
Wireless Router
Wireless Router
Camcorder
AP
Mobile
Internet
Before inital using wirless connections, download and install APP
[Unieye Drive] from Google Play Store and Apple Store.
[Unieye Drive] has two functions:
(1) Local - Direct control (2) Internet - Internet live view
Unieye Drive
Local
(1)
【
Mobile connects to camcorder directly via WiFi for remote control,
live view, album management and camcorder setup.
Internet
(2)
【
Mobile connects to cloud server to view live videos uploaded
from internet remote camcorder.
Local
Internet
Local Internet
】
】
English
| 5
Page 7
Local】Function
Internet
【
Local
Before using mobile APP's【Local】function, ensure camcorder WiFi
is on and camcorder Cloud setting is off. Once WiFi is ready, preview
shows camcorder name (R2-xxxxxxxx) for few seconds.
Mobile Connects to Camcorder
1. F
or Android: Turn on [Wi-Fi].
For iOS:
2. Run [Unieye Drive].
3. Tap【Local】and select the camcorder to enter【Local】View
Page. Tap [ ] to scan again if camcorder is not found.
Note:
• Mobile cannot connect to camcorder while camcorder is recording.
• For rst use, password is not required. User can set camcorder
password in Setup Page.
Go to [Settings] [Wi-Fi].
Turn on [Wi-Fi] and select the camcorder name.
6 |
iOS Settings
English
Local View PageLocal Main Page
Page 8
4.【Local】function has three function pages: View, Album and Setup.
View Page
Items Descriptions
Shoot videos and les are saved into camcorder microSD card
Shoot videos or Take photos and les are saved into
mobile "Album\Unieye Drive
\"
For multiple camcorders user :
• Enable Quad-View for multiple live view on mobile
• In Quad-View, select
a window for single view.
Upside down image
Talk to camcorder from mobile
Album Page
(for camcorder)
Folders Descriptions
View or delete video les recorded in action cam mode
View or delete video les recorded in dash cam mode
Setup Page (for camcorder)
Groups Descriptions
Camcorder Settings
Internet Settings
Edit name, password, format SD card, resolution
etc.
Edit Email and AP and save in camcorder.
(For internet cloud server connection)
Car DVR Settings Set motion detector, impact sensor, etc.
1.
Note:
In Setup Page, tap [Save] to complete settings to camcorder.
2.
Mobile media player may not support SuperHD video.
English
| 7
Page 9
Camcorder SD Card Setup
AP
AP
AP
AP
AP
AP
When SD card is rst-time use or reformatted in camcorder, user should
allocate memory for Portable Mode and Car Mode.
Go to [Setup] [ Camcorder Settings
]
Adjust slide bar and press [Format]
button to complete SD card setup.
Camcorder Internet Setup
Before using internet cloud service, Email and AP must be properly
set up.
1. Go to [Setup] [ Internet Settings
Edit Email and AP
2. Tap [Save] to complete Email & AP
settings.
Note: AP(Access Point) can be
• Wireless Router or
• 3G/4G Mobile Wireless Router or
• 3G/4G Mobile Hotspot
Wireless Router
8 |
English
]
3G/4G Mobile
Wireless Router
3G/4G
Mobile Hotspot
Page 10
Motion Detector Setup
When car's engine stops and motion is detected,
camcorder automatically records videos till no
motion is detected.
1. Set Camcorder to dash cam mode.
2. Go to APP [Setup] [ Car DVR Settings]
Turn on [Motion Detector] Tap [Save].
3. Camcorder shows on screen.
4. When car's engine stops, operate camcorder
to active [ Motion Detector].
G-Sensor Setup
When camcorder is recording and any impacts happen, camcorder
automatically records emergency events if G-Sensor is set.
Go to APP [Setup] [ Car DVR Settings]
Select [G-Sensor], [H]/[L] Tap [Save].
Note : [H] High sensitivity. [L] Low sensitivity.
English
| 9
Page 11
Internet】Function
【
Internet
Before using APP's【Internet】function, ensure camcorder internet
setup has been completed.
Camcorder Connects to Cloud Server
Enable [Cloud ] in camcorder to upload video streaming to cloud
server. Connecting status will be shown on screen.
Status Descriptions
Connection successful. Preview shows [ ] and
camcorder ID.
Login fail:
• Invalid AP name or password
• Weak WiFi signal or not in WiFi coverage
Connection fail:
• No internet or cloud server is not accessible
• Blocked by some rewall
Remote Internet Live View
1. Connect mobile to internet (via WiFi, 3G/4G).
2. Run [Unieye Drive] and tap【Internet】.
3. For adding camcorder or using another
mobile, tap [ ] Enter the camcorder ID
and password.
4. Tap camcorder ID/name to view internet live
videos.
Main Page
Internet
【
】
English
10 |
Page 12
Troubleshooting
Situation Cause/Solution
Camcorder cannot
turn on
Camcorder is
frozen
Camcorder cannot
record
Camcorder cannot
connect to AP or
could server
Mobile cannot nd
camcorder
Local
【
】
Mobile cannot watch
live view
Local
【
】
Mobile cannot connect
to cloud server
Internet
【
】
Mobile cannot watch
live view
Internet
【
】
Forget camcorder
password
Power is low. Recharge battery
Press and hold button for 5 seconds to force
shutdown; press again to turn on
•
No microSD card or microSD card is full
•
microSD card cannot be recognized
•
Format microSD card or replace microSD card
• Invalid AP name or password
• Weak WiFi signal or not in WiFi coverage
• No internet or cloud server is not accessible
• Blocked by some rewall
• Camcorder WiFi is disabled or not in WiFi
coverage
• Mobile WiFi is disabled
• iOS user does not choose camcorder name in
Wi-Fi Settings
• Tap [Refresh] button on [Unieye Drive]
• Weak WiFi signal
• Camcorder is recording
• Camcorder is occupied by other mobile
Check mobile 3G/4G or WiFi internet
connection
The internet bandwidth is insufcient for
camcorder upload or mobile download
Enter camcorder menu settings and select
[Settings] [Factory Reset] to reset
English
| 11
Page 13
FCC Regulations:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s
authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Compliance (SAR)
This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency
(RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard
for wireless devices employs a unit of measurement known as the Specific Absorption Rate (SAR). The SAR
limit adopted by the FCC is 1.6W/kg for an uncontrolled environment. Tests for SAR are conducted using
standard operating positions accepted by the FCC with the device transmitting at its highest certified power
level in all tested frequency bands. The FCC has granted an Equipment Authorization for this device with all
reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines.
Although the SAR is determined at the highest certified power level, the actual SAR level of the device while
operating can be well below the maximum value. This is because the device is designed to operate at multiple
power levels so as to use only the poser required to reach the network. In general, the closer you are to a
wireless base station antenna, the lower the power output.
Loading...