Page 1
GAS HANDHELD CUT-OFF SAW
66753
SET UP, OPERATING, AND SERVICING
INSTRUCTIONS
Using an engine indoors CAN KILL YOU IN
MINUTES.
Engine exhaust contains carbon monoxide.
This is a poison you cannot see or smell.
NEVER use inside
a home or garage,
EVEN IF doors and
windows are open.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Only use OUTSIDE
and far away from
windows, doors, and
vents.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2009 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Page 2
CONTENTS
IMPORTANT SAFETY
INFORMATION ............................ 3
CUT-OFF SAW SAFETY
PRECAUTIONS ........................... 5
VIBRATION HAZARD: ..................7
SPECIFICATIONS ..........................9
PARTS LISTS AND DIAGRAMS . 21
DRIVE SYSTEM PARTS LIST &
DIAGRAM ......................................21
BLADE GUARD ASSEMBLY
PARTS LIST & DIAGRAM .............22
FLANGE ASSEMBLY PARTS LIST
& DIAGRAM ...................................23
CLUTCH ASSEMBLY PARTS LIST
& DIAGRAM ...................................24
UNPACKING .................................. 9
COMPONENTS AND CONTROLS ....9
SET UP INSTRUCTIONS .............10
ASSEMBLY.......................................10
ABRASIVE BLADE RING TEST . 11
INSTALLING THE BLADE .......... 11
FILLING THE FUEL TANK .........12
OPERATING INSTRUCTIONS .... 12
STARTING THE ENGINE .................12
BREAK-IN PERIOD ....................13
CUTTING TECHNIQUE ...............14
SERVICING ..................................15
MAINTENANCE PROCEDURES .....15
COOLING SYSTEM ....................15
AIR FILTER ELEMENT
MAINTENANCE .......................16
SPARK PLUG MAINTENANCE ..16
FUEL FILTER REPLACEMENT ..17
CLEANING, MAINTENANCE, AND
LUBRICATION SCHEDULE ..........18
WEEKLY MAINTENANCE: .........18
MONTHLY MAINTENANCE: .......18
STORAGE ........................................18
TROUBLESHOOTING ......................19
HANDLE ASSEMBLY PARTS LIST
& DIAGRAM ...................................24
CONTROL SYSTEM PARTS LIST
& DIAGRAM ...................................25
AIR FILTER ASSEMBLY PARTS
LIST & DIAGRAM ..........................26
CARBURETOR ASSEMBLY
PARTS LIST & DIAGRAM .............27
RECOIL ASSEMBLY PARTS LIST
& DIAGRAM ...................................28
IGNITION ASSEMBLY PARTS
LIST & DIAGRAM ..........................29
CYLINDER ASSEMBLY PARTS
LIST & DIAGRAM ..........................30
MUFFLER ASSEMBLY PARTS
LIST & DIAGRAM ..........................31
CRANKSHAFT ASSEMBLY
PARTS LIST & DIAGRAM .............32
CRANKCASE ASSEMBLY PARTS
LIST & DIAGRAM ..........................33
WET CUTTING KIT PARTS LIST &
DIAGRAM ......................................34
LIMITED 90 DAY WARRANTY .... 35
EMISSION CONTROL SYSTEM
WARRANTY ..............................35
SKU 66753 For technical questions, please call 1-800-444-3353. Page 2
Page 3
SAVE THIS MANUAL
Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning
procedures. Write the product’s serial
number in the back of the manual near the
assembly diagram (or month and year of
purchase if product has no number). Keep
this manual and the receipt in a safe and
dry place for future reference.
IMPORTANT SAFETY
INFORMATION
In this manual, on the labeling,
and all other information
provided with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
NOTICE is used to
address practices
not related to personal injury.
CAUTION, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
WARNING! Read all instructions.
Failure to follow all instructions
listed below may result in re,
serious injury and/or DEATH.
The warnings and precautions
discussed in this manual cannot
cover all possible conditions and
situations that may occur. It must
be understood by the operator that
common sense and caution are
factors which cannot be built into
this product, but must be supplied
by the operator.
SAVE THESE INSTRUCTIONS
SET UP PRECAUTIONS
Gasoline fuel and fumes are amma-1.
DANGER indicates
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
WARNING
indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.
CAUTION, used
with the safety
alert symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 3
ble, and potentially explosive. Use
proper fuel storage and handling procedures. Do not store fuel or other
ammable materials nearby.
Have multiple ABC class re extin-2.
guishers nearby.
Operation of this equipment may cre-3.
ate sparks that can start res around
dry vegetation.
A spark arrestor may be required.
The operator should contact local re
agencies for laws or regulations relat-
ing to re prevention requirements.
Set up and use only on a at, level, 4.
well-ventilated surface.
Page 4
Wear ANSI-approved safety goggles, 5.
heavy-duty work gloves, and dust
mask/respirator during set up.
Use only oil and fuel recommended 6.
in the “Specications” section of this
manual.
People with pacemakers should 5.
consult their physician(s) before
use. Electromagnetic elds in close
proximity to a heart pacemaker could
cause pacemaker interference or
pacemaker failure. Caution is necessary when near the engine’s magneto
or recoil starter.
OPERATING PRECAUTIONS
1. CARBON MONOXIDE
HAZARD
Using an engine indoors
CAN KILL YOU IN
MINUTES.
Engine exhaust contains carbon
monoxide. This is a poison you
cannot see or smell.
NEVER use inside a home or garage,
EVEN IF doors and windows are
open.
Only use OUTSIDE and far away
from windows, doors, and vents.
Keep children away from the equip-2.
ment, especially while it is operating.
Do not leave the equipment unat-3.
tended when it is running. Turn off
the equipment (and remove safety
keys, if available) before leaving the
work area.
Wear ANSI-approved safety goggles 4.
and hearing protection during use.
Use only accessories that are recom-6.
mended by Harbor Freight Tools for
your model. Accessories that may be
suitable for one piece of equipment
may become hazardous when used
on another piece of equipment.
Do not operate in explosive atmo-7.
spheres, such as in the presence of
ammable liquids, gases, or dust.
Gasoline-powered engines may ignite
the dust or fumes.
Stay alert, watch what you are doing 8.
and use common sense when operating this piece of equipment. Do not
use this piece of equipment while
tired or under the inuence of drugs,
alcohol or medication.
Do not overreach. Keep proper foot-9.
ing and balance at all times. This enables better control of the equipment
in unexpected situations.
Use this equipment with both hands 10.
only. Using equipment with only
one hand can easily result in loss of
control.
Dress properly. Do not wear loose 11.
clothing or jewelry. Keep hair, clothing and gloves away from moving
parts. Loose clothes, jewelry or long
hair can be caught in moving parts.
Parts, especially exhaust system 12.
components, get very hot during use.
Stay clear of hot parts.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 4
Page 5
Do not cover the engine or equipment 13.
during operation.
Keep the equipment, engine, and sur-14.
rounding area clean at all times.
Use the equipment, accessories, etc., 15.
in accordance with these instructions
and in the manner intended for the
particular type of equipment, taking
into account the working conditions
and the work to be performed. Use
of the equipment for operations different from those intended could result
in a hazardous situation.
Use the correct equipment for the 21.
application. Do not modify the equipment and do not use the equipment
for a purpose for which it is not intended.
CUT-OFF SAW SAFETY
PRECAUTIONS
Never use carbide-tipped, woodcut-1.
ting, or circular machine Saw Blades.
They can cause severe personal
injury from reactive forces, blade contact, or thrown objects.
Do not operate the equipment with 16.
known leaks in the engine’s fuel system.
This product contains or, when used, 17.
produces a chemical known to the
State of California to cause cancer
and birth defects or other reproductive harm. (California Health & Safety
Code § 25249.5, et seq.)
When spills of fuel or oil occur, they 18.
must be cleaned up immediately.
Dispose of uids and cleaning materials as per any local, state, or federal
codes and regulations. Store oil rags
in a bottom-ventilated, covered, metal
container.
Keep hands and feet away from 19.
moving parts. Do not reach over or
across equipment while operating.
Before use, check for misalignment 20.
or binding of moving parts, breakage
of parts, and any other condition that
may affect the equipment’s operation.
If damaged, have the equipment
serviced before using. Many ac-
cidents are caused by poorly maintained equipment.
Only cut asphalt, concrete, stone, 2.
brick, and plastics with this Cut Off
Saw.
Inspect the Saw Blade frequently, 3.
and replace immediately if the Blade
is cracked, or warped. Cracked or
warped Saw Blades may shatter or
break and cause serious personal
injury.
Always install the Saw Blade so 4.
that the arrow on the Blade points
in the direction of the rotation of
the spindle.
Keep hands and ngers away from 5.
the cutting area and Saw Blade.
Never attempt to cut more than 6.
one workpiece at a time.
When cutting a large workpiece, 7.
make sure its entire length is properly supported. If necessary, use a
roller stand (not included).
Allow the Saw Blade to spin up to 8.
full speed before feeding it into a
workpiece. When turning off the Cut
Off Saw, allow the Saw Blade to spin
down and stop on its own. Do not
SKU 66753 For technical questions, please call 1-800-444-3353. Page 5
Page 6
press against the Saw Blade to stop
it.
Do not force the Saw Blade into 9.
the workpiece when cutting. Apply
moderate pressure, allowing the Saw
Blade to cut without being forced.
To avoid accidental injury, always 10.
wear heavy duty work gloves when
changing the Saw Blade.
The Saw Blade will become hot 11.
while cutting. Allow the Saw Blade
to completely cool before handling.
twisted or misaligned in the cut, the
teeth at the back edge of the Saw
Blade can raise the Cut Off Saw
(walk up) toward the operator. Kickback is a result of tool misuse and/
or incorrect operating procedures or
conditions and can be avoided by
taking proper precautions as given
below:
Maintain control of the Cut Off •
Saw at all times. Never allow the
rotating Saw Blade to rest on the
workpiece without holding on to the
Saw with both hands.
Turn off the Cut Off Saw and allow 12.
the Saw Blade to completely stop
if the Saw Blade is to be backed
out of an uncompleted cut.
Never attempt to remove material 13.
stuck in the Cut Off Saw while it is
operating.
Always use the water cooling 14.
system when cutting concrete to
avoid inhalation of dangerous dust
particles.
Make sure the workpiece is free 15.
from nails, metal rebar, and any
other foreign objects that could
damage the Saw Blade or cause
“kickback”.
Causes and operator prevention 16.
of “kickback”: Kickback is a sud-
den reaction to a pinched, bound, or
misaligned Saw Blade, causing an
uncontrolled Cut Off Saw to lift up
and out from the workpiece toward
the operator. When the Saw Blade
is pinched or bound tightly by the cut
closing down, the Saw Blade stalls
and the engine reaction drives the
Cut Off Saw rapidly back toward the
operator. If the Saw Blade becomes
When the Saw Blade is binding, •
or when interrupting a cut for
any reason, turn off the Cut Off
Saw and hold the Saw motionless until the Saw Blade comes
to a complete stop. Never attempt
to remove the Saw Blade from the
workpiece or pull the Saw backward
while the Saw Blade is in motion or
kickback may occur. Investigate and
take corrective actions to eliminate
the cause of Saw Blade binding.
When restarting the Cut Off Saw •
on a workpiece, center the Saw
Blade in the pre-cut opening and
check that the Saw Teeth are not
engaged into the workpiece. If the
Saw Blade is binding, the Cut Off
Saw may walk up or kickback as the
Saw is restarted.
Support large panels with roller •
stands (not included) to minimize
the risk of Saw Blade pinching
and kickback. Large panels tend
to sag under their own weight. Supports must be placed under the
panel and near the outer edge of the
panel.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 6
Page 7
Do not use a dull or damaged Saw •
Blade. Unsharpened or improperly
installed Saw Blades produce a narrow cut causing excessive friction,
Saw Blade binding and kickback.
hands and ngers, increasing the risk
of vibration-related injury.
Wear suitable gloves to reduce the 3.
vibration effects on the user.
Push the Saw Blade past the •
workpiece prior to release.
Make sure to check the Blade •
Guard for proper operation. Never
disable the Guard. Do not use the
Cut Off Saw if the Guard assembly
does not operate properly. Before
each use, make sure the Blade
Guard does not touch the Saw
Blade.
Vibration Hazard:
This tool vibrates during use. Repeated or long-term exposure to
vibration may cause temporary or
permanent physical injury, particularly
to the hands, arms and shoulders. To
reduce the risk of vibration-related
injury:
Anyone using vibrating tools regu-1.
larly or for an extended period should
rst be examined by a doctor and
then have regular medical checkups to ensure medical problems are
not being caused or worsened from
use. Pregnant women or people
who have impaired blood circulation
to the hand, past hand injuries, nervous system disorders, diabetes, or
Raynaud’s Disease should not use
this tool. If you feel any symptoms
related to vibration (such as tingling,
numbness, and white or blue ngers),
seek medical advice as soon as possible.
Do not smoke during use. Nico-2.
tine reduces the blood supply to the
Use tools with the lowest vibration 4.
when there is a choice between different processes.
Include vibration-free periods each 5.
day of work.
Grip tool as lightly as possible (while 6.
still keeping safe control of it). Let
the tool do the work.
To reduce vibration, maintain the tool 7.
as explained in this manual. If any
abnormal vibration occurs, stop use
immediately.
SERVICE PRECAUTIONS
Before service, maintenance, or 1.
cleaning:
Turn the ON/OFF switch to its a.
“OFF” position.
Allow the engine to completely b.
cool.
Then, remove the spark plug c.
wire(s) from the spark plug(s).
Keep all safety guards in place and in 2.
proper working order. Safety guards
include mufer, air cleaner, mechanical guards, and heat shields, among
other guards.
Do not alter or adjust any part of 3.
the equipment or its engine that is
sealed by the manufacturer or dis-
tributor. Only a qualied service
technician may adjust parts that
may increase or decrease governed engine speed.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 7
Page 8
Wear ANSI-approved safety goggles, 4.
heavy-duty work gloves, and dust
mask/respirator during service.
Maintain labels and nameplates on 5.
the equipment. These carry important information. If unreadable or
missing, contact Harbor Freight Tools
for a replacement.
Have the equipment serviced by a 6.
qualied repair person using only
identical replacement parts. This will
ensure that the safety of the equipment is maintained. Do not attempt
any service or maintenance procedures not explained in this manual
or any procedures that you are uncertain about your ability to perform
safely or correctly.
Store equipment out of the reach of 7.
children.
Follow scheduled engine and equip-8.
ment maintenance.
Refueling Precautions:9.
Do not smoke, or allow sparks, a.
ames, or other sources of ignition
around the equipment, especially
when refuelling.
Do not rell the fuel tank while the b.
engine is running or hot.
Do not ll fuel tank to the top. Leave c.
a little room for the fuel to expand as
needed.
Refuel in a well-ventilated area only.d.
SAVE THESE
INSTRUCTIONS.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 8
Page 9
SPECIFICATIONS
UNPACKING
Type 2 Stroke, air cooled
Engine
Bore x Stroke 1.89” x 1.34”
Compression Ratio 7.5:1
Displacement 61.5 cc
Sound Level 105 dB @ 3 ft.
Fuel
Spark Plug
Speed
Blade
(not
included)
Max. Cutting Depth 4-1/2”
Belt SPZ 900
Air Filter
Rating 4.7 horsepower
Start Recoil
Type
Fuel/Oil Ratio 40:1
Capacity 0.7 L (0.18 Gallons)
Type
Gap 0.02” (0.5mm)
Idle 2600 RPM
No Load 9500 RPM
Size
Arbor 1” / 20 mm
90+octane unleaded
gasoline/2-cycle oil
NGK - BPMR7A
TORCH - L6RTC
14” dia.
7/64” to 1/4” thick
Prelter (Foam)
Paper Cartridge
Flocked Aux.
Note: Additional specications found in
the TECHNICAL ENGINE SPECIFICATIONS chart in this manual.
The emission control system for this
Saw’s Engine is warranted for standards
set by the U.S. Environmental Protection
Agency and by the California Air Resources Board (also known as CARB). For warranty information, refer to the last pages of
this manual.
When unpacking, make sure that the
item is intact and undamaged. If any parts
are missing or broken, please call Harbor
Freight Tools at 1-800-444-3353 as soon
as possible.
Components and Controls
Front Handle (8E)
Air Filter Cover (5G)
Trigger
Starter
Handle (13I)
Decompression
Valve (13K)
Trigger
Locking
Button
Starter
Cover (4I)
Gas Cap (17F)
Water Valve (3O)
Blade Guard
Adjustment
Handle (8B)
Safety Lever
ON/OFF
Switch (14G)
Blade
Guard
(7B)
At high altitudes, the engine’s carburetor, governor (if so equipped), and any
other parts that control the fuel-air ratio will
need to be adjusted by a qualied mechanic to allow efcient high-altitude use
and to prevent damage to the engine and
any other devices used with this product.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 9
Choke (6H)
Trigger (7F)
Belt Guard (7A)
Quick Connect
Hose Fitting (5O)
Figure 1
Blade
Page 10
SET UP INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
Assembly
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
STARTING:
Turn the Power Switch of the
equipment to its “OFF”
position, wait for the engine to
cool, and disconnect the
spark plug wire(s) before
assembling or making any
adjustments to the equipment.
TO PREVENT
SERIOUS INJURY:
Operate only with proper
spark arrestor installed.
Operation of this equipment
may create sparks that
can start res around dry
vegetation.
A spark arrestor may be
required.
The operator should contact
local re agencies for laws
or regulations relating to re
prevention requirements.
Abrasive
Blade
Diamond
Blade
Figure 2
Cutting blades are available in two
standard designs: abrasive blades
and diamond blades. Before using
any blade, check it for damage. Use
the ring-test, described in next section, for abrasive blades and check
diamond blades for bent or damaged
anges or accumulated dirt.
Note: For additional information regarding
the parts listed in the following pages,
refer to the Parts Lists and Assembly
Diagrams near the end of this
manual.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 10
Page 11
Abrasive Blade Ring Test
Installing the Blade
Closely inspect the blade before
mounting. Perform a ring-test on the
blade as follows:
Suspend the blade using a pin or 1.
nger through the arbor hole.
45° 45°
Hang
Wheel
from
Pin
V
E
R
T
I
C
A
L
Tap
Wheel
Here
45° 45°
C
E
N
T
E
R
Figure 3
2. Tap the at side of the blade with a
light non-metallic object, such as a
screwdriver handle, at a point 45°
from the vertical center line on each
side of the blade and 1 – 2 inches
from the edge of the blade - See
Figure 3.
Rotation
Direction
Arrow
Hex Bolt
(20C)
Outside
Flange (5B)
Blade Guard (7B)
Arbor (13C)
(not shown)
Figure 4
1. Loosen and remove the Hex Bolt
(20C). Then, remove the Outside
Flange (5B).
The Inner Flange must be oriented 2.
so that it matches perfectly with the
arbor hole of the blade (one side is 1”
and the other side is 20 mm).
Mount the new Saw Blade (not in-3.
cluded) on the Arbor (13C).
IMPORTANT: 4. The arrow shown
on the Saw Blade must point in the
same direction as the arrow shown
on the Blade Guard (7B).
Rotate the blade 45 degrees and 3.
repeat the test until the entire wheel
has been checked.
An undamaged blade will give a clear 4.
tone. If cracked, there will be a dead
sound and not a clear ring. Do not
use a damaged blade.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 11
Once the Saw Blade (not included) is 5.
mounted on the Arbor (13C), replace
the Outside Flange (5B) and rmly
tighten the Hex Bolt (20C) to secure
the Saw Blade in place.
Make sure to check the Blade Guard 6.
(7B) for proper operation. Never disable the Guard. Do not use the Cut
Off Saw if the Guard assembly does
not operate properly. Before each
use, make sure the Blade Guard
does not touch the Saw Blade.
Page 12
Filling the Fuel Tank
WARNING! TO PREVENT
SERIOUS INJURY FROM
FIRE:
Mix the fuel (see below) and ll
the fuel tank in a well-ventilated area
away from ignition sources. Do not
smoke.
Once the proper fuel mix is obtained, 3.
wipe gas cap (17F) and its surrounding area, then remove the Gas Cap.
Fill the Fuel Tank approximately 3/4
full with the fuel mix (the Fuel Tank
capacity is 0.18 gallons). Then, replace the Gas Cap.
OPERATING INSTRUCTIONS
WARNING! Your Warranty is voided if: You do not operate the Cut
Off Saw with the proper 40:1 fuel
mix in its Fuel Tank. Never run the
Engine with an improper fuel mix,
low or no fuel mix. Running the
Engine with an improper fuel mix,
low or no fuel mix will permanently
damage the unit. Only use 2-stroke
engine oil for air cooled engines.
Never use outboard engine oil.
To obtain the proper 40:1 fuel mix, 1.
combine 2 stroke engine oil with unleaded gasoline (minimum 90 octane
rating) in a clean, approved container.
To mix the fuel:
Add half the amount of fuel and the a.
entire amount of oil.
Cover and shake the fuel mixture. b.
Add the remaining amount of fuel.c.
Cover and shake to thoroughly mix 2.
before each fueling. Refer to the
Chart below for proper mix quantities.
NOTE: Mix only enough fuel for a
few days work. The maximum storage time of mixed fuel is 3 months.
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
Starting the Engine
Inspect engine and equipment
looking for damaged, loose,
and missing parts before
set up and starting. If any
problems are found, do not use
equipment until xed properly.
Before starting the engine:
Follow the Set Up Instruc-a.
tions to prepare the equipment.
Inspect the equipment and b.
engine.
Fill the engine with the prop-c.
er amount and type of fuel
and oil mixture.
Read the Equipment Opera-d.
tion section that follows.
FUEL MIX QUANTITIES
Ratio 2 Stroke
Engine Oil
40:1 4 Fl. Oz. 1.2 Gal.
40:1 8 Fl. Oz. 2.4 Gal.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 12
Unleaded Gasoline
(90 Octane)
The cutting blade
may rotate when the engine starts.
Note: Refer to the Components and Con-
trols Diagram, Figure 1 on page 10
for the following instructions.
Page 13
Turn ON the ON/OFF Switch (14G).1.
If the engine is cold, pull out the 2.
Choke (6H). If the engine is warm,
press in the Choke.
Hold the Trigger Safety Lever in using 3.
your palm, squeeze the Trigger (7F)
and then press in the Trigger Locking
Button (see Figure 1, page 9 for location of controls). Release the Trigger,
then release the Trigger Locking Button and the Trigger Safety Lever. The
Trigger should remain locked in the
engaged position.
Press in the Decompression Valve 4.
(13K).
after each start-up to allow the engine
to stabilize.
If the engine does not start, press the 9.
Decompression Valve Button (7B) in
and attempt to start it again.
To stop the engine, turn off the ON/10.
OFF Switch.
After use, to prevent accidents, turn 11.
off the engine, wait for the engine to
cool, then disconnect its spark plug
wire after use. Clean external parts
with clean cloth, then store the equipment out of children’s reach according to the Storage instructions in this
manual.
Place the Cut Off Saw on the ground. 5.
Hold the Front Handle (8E) with your
right hand and put your right foot on
the lower part of the rear handle.
Grip the Starter Handle (13I) with 6.
your left hand, and slowly pull until
you feel resistance. Once you feel
resistance, pull quickly and rmly,
several times if needed, until the engine starts.
Note: Do not pull the Starter Cord com-
pletely out and do not release the
Starter Handle from the fully extended position. This can damage
the saw. Hold the Starter Handle and
guide the Starter Cord as it recoils
back into the machine.
Once the engine starts, squeeze the 7.
Trigger. The engine should idle down
but not cut off.
Break-in Period
Breaking-in the engine will help to 1.
ensure proper equipment and engine
operation, and will extend the engine’s lifespan.
During the rst 3 hours of use:2.
Do not apply a heavy load to the 3.
equipment.
Do not operate the engine at its maxi-4.
mum speed.
Under normal operating conditions 5.
subsequent maintenance follows the
schedule explained in the Maintenance and Servicing section.
If the Choke was pulled out, slowly 8.
push in the choke.
IMPORTANT: Allow the engine to run
at no load until warm (1-5 minutes)
SKU 66753 For technical questions, please call 1-800-444-3353. Page 13
Page 14
Cutting Technique
Cut
Figure 7
Supports
Figure 5
1. Support the material being cut so
that the cut will open up as the cut is
made, rather than pinch together.
Always cut at full throttle.2.
Start cutting gently, do not force or 3.
squeeze the blade into the material or
the groove of the cut.
7. To avoid kickback, never cut with
the upper section of the blade - See
Figure 7.
Abrasive Blades are not intended for 8.
use with water.
When cutting concrete always use 9.
the water cooling system. To use the
water cooling system:
Before starting the engine attach a a.
garden hose to the Quick Connect
Hose Fitting (5O).
Turn on the hose.b.
Start the engine.c.
Figure 6
4. Move the blade slowly backwards
and forwards, using a small part of
the cutting edge of the blade to slowly
cut material. Do not cut only in one
direction - See Figure 6.
Keep the blade at a right angle to the 5.
cutting surface.
Never cut above shoulder height.6.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 14
Page 15
SERVICING
Cooling System
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
STARTING:
Turn the Power Switch of the
equipment to its “OFF”
position, wait for the engine to
cool, and disconnect the
spark plug wire(s) before
performing any inspection,
maintenance, or cleaning
procedures.
TO PREVENT
SERIOUS INJURY
FROM EQUIPMENT FAILURE:
Do not use damaged
equipment. If abnormal noise,
vibration, or excess smoking
occurs, have the problem
corrected before further use.
Maintenance Procedures
Many maintenance procedures,
including those not detailed
in this manual, will need to
be performed by a qualied
technician for safety. If you
have any doubts about your
ability to safely service the
equipment or engine, have a
qualied technician service the
equipment instead.
Cylinder Cover
Cooling Fins on
Cylinder
Air Flow
Guide
Cooling Fins on
Flywheel
Air Intake
Figure 8
Clean the cooling system using a
brush or compressed air at the end of
each day. A dirty or blocked cooling system results in overheating, which causes
damage to the piston and cylinder.
Note: Warranty is void if proper mainte-
nance and servicing procedures are
not followed.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 15
Page 16
Air Filter Element Maintenance
Air Filter Covers (1G/5G)
Paper Filter (12G)
Foam Filter (4G)
and mild detergent several times.
Rinse thoroughly. Squeeze out excess water and allow it to dry com-
pletely. Soak the lter in lightweight
oil briey, then squeeze out the
excess oil.
Install the new lters or the cleaned 5.
lters. Secure the Air Filter Cover
before use.
Spark Plug Maintenance
0.02”
Figure 9
Filter Screen (13G)
1. Wipe off the Air Filter Covers
(1G/5G).
Unthread the screws which hold the 2.
covers in place and remove the covers.
Remove the air lter element.3.
Cleaning:4.
For the Paper Filter (12G): a.
To prevent injury from dust and
debris, wear ANSI-approved safety
goggles, NIOSH-approved dust
mask/respirator, and heavy-duty
work gloves. In a well-ventilated
area away from bystanders, use
pressurized air to blow dust out
of the air lter from the side opposite the lter’s normal air ow (the
“clean” side of the lter).
If this does not get the lter reason-
ably clean, replace it.
Figure 10
1. Disconnect spark plug wire from
end of plug. Clean out debris from
around spark plug.
Using a spark plug wrench, remove 2.
the spark plug.
Inspect the spark plug:3.
If the electrode is oily, clean it using a.
a clean, dry rag.
If the electrode has deposits on it, b.
polish it using emery paper.
For the Foam Filter (4G): b.
Wash the element in warm water
SKU 66753 For technical questions, please call 1-800-444-3353. Page 16
Page 17
If the white insulator is cracked or c.
chipped, the spark plug needs to be
replaced.
When installing a new spark plug, ad-4.
just the plug’s gap to the specication
on the Technical specication chart.
Do not pry against the electrode or
the insulator, the spark plug can be
damaged.
Place a suitable container under the 5.
Fuel Filter.
Disconnect the fuel lines leading to 6.
and from the Fuel Filter and allow fuel
to drain onto the container.
Install new Fuel Filter in the same 7.
orientation. Properly secure both fuel
lines.
Install the new spark plug or the 5.
cleaned spark plug into the engine.
Gasket-style: Finger-tighten until the
gasket contacts the cylinder head,
then about 1/2-2/3 turn more.
Non-gasket-style: Finger-tighten until
the plug contacts the head, then
about 1/16 turn more.
Apply dielectric spark plug boot 6.
protector (not included) to the end of
the spark plug and reattach the wire
securely.
Fuel Filter Replacement
WARNING! TO PREVENT
SERIOUS INJURY FROM
FIRE:
Replace the Fuel Filter (16F) in
a well-ventilated area away from
ignition sources. Do not smoke.
Clean up and properly dispose of all 8.
fuel.
Wait for at least one hour before use 9.
to allow all residual fuel vapors to
dissipate. To prevent FIRE, do not
start the engine while the smell of
fuel hangs in the air. Remember to
open the fuel valve before restarting
the engine. It may take a little longer
than usual to start the engine be-
cause the fuel needs to rell the fuel
line and new lter.
Wait for engine to cool completely 1.
before proceeding.
Wear protective gear including, ANSI-2.
approved safety goggles, NIOSHapproved dust mask/respirator, and
nitrile gloves.
Close fuel valve leading from gas 3.
tank completely.
Take note of the Fuel Filter’s orienta-4.
tion.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 17
Page 18
Cleaning, Maintenance, and
Lubrication Schedule
Note: This maintenance schedule is
intended solely as a general guide.
If performance decreases or if equipment operates unusually, check systems immediately. The maintenance
needs of each piece of equipment
will differ depending on factors such
as duty cycle, temperature, air quality, fuel quality, and other factors. If
you have doubts about your ability to
safely service this tool, have a quali-
ed technician service the equipment
instead.
Storage
Wait for engine to cool, then clean 1.
engine with clean cloth.
Remove the blade from the Saw and 2.
store separately.
Abrasive blades should be handled 3.
with care to prevent damage. Store
abrasive blades on a at level surface.
When the equipment is to remain idle 4.
for longer than 20 days, prepare the
engine for storage as follows:
Empty fuel tank.a.
Note: These procedures are in addition to
the regular checks and maintenance
explained as part of the regular operation of the engine and equipment.
Weekly Maintenance:
Clean the cooling system as de-a.
scribed under Servicing-Cooling
System. Check the lters, clean or
replace as needed.
Check and clean the spark plug.b.
Clean the Cooling Fins on the Cylin-c.
der (1K).
Check the mufer.d.
Check the carburetor.e.
Blow dust off with compressed air.f.
Monthly Maintenance:
Clean out area around spark plug. b.
Remove spark plug and pour one
tablespoon of engine oil into cylinder
through spark plug hole.
Reinstall spark plug, but leave spark c.
plug wire disconnected.
Pull recoil starter to distribute oil in d.
cylinder. Stop after one or two revolutions.
Apply a thin coat of rust preventive oil 5.
to all uncoated metal parts.
Cover and store in a dry, well-ventilat-6.
ed area out of reach of children.
Check the clutch drum, drive-pulley, a.
clutch springs for wear.
Clean the outside of the carburetor.b.
Check the fuel lter and fuel hose. c.
Change if needed.
Clean the inside of the fuel tank.d.
Check all cables and connectionse.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 18
Page 19
Troubleshooting
Engine will not
start
FUEL RELATED:
No fuel in tank or fuel valve closed.1.
Choke not in start position, 2.
especially with cold engine.
Low quality or deteriorated, old 3.
gasoline.
Dirty fuel passageways blocking fuel 4.
ow.
Carburetor needle stuck. Fuel can 5.
be smelled in the air.
Too much fuel in chamber. This can 6.
be caused by the carburetor needle
sticking.
IGNITION (SPARK) RELATED:
Spark plug wire disconnected or not 1.
connected securely.
Spark plug electrode wet or dirty.2.
Incorrect spark plug gap.3.
Spark plug wire or spark plug 4.
broken.
Incorrect spark timing or faulty 5.
ignition system.
COMPRESSION RELATED:
Cylinder not lubricated. Problem 1.
after long storage periods.
Loose or broken spark plug. 2.
(Hissing noise will occur when trying
to start.)
Loose cylinder head or damaged 3.
head gasket. (Hissing noise will
occur when trying to start.)
Engine valves or tappets 4.
misadjusted or stuck.
FUEL RELATED:
Fill fuel tank and open fuel valve.1.
Move choke to start position if 2.
engine is cold.
Use only fresh 90+ octane unleaded 3.
gasoline in proper mixture with
2-stroke engine oil.
Clean out passageways using 4.
fuel additive. Heavy deposits may
require further cleaning.
Gently5. tap side of carburetor oat
chamber with screwdriver handle.
Turn choke to run position. Remove 6.
spark plug and pull the start handle
several times to air out the chamber.
Reinstall spark plug and set choke
to start position.
IGNITION (SPARK) RELATED:
Connect spark plug wire properly. 1.
Clean spark plug.2.
Correct spark plug gap.3.
Replace spark plug wire and/or 4.
spark plug.
Have qualied technician diagnose/5.
repair ignition system.
COMPRESSION RELATED:
Pour tablespoon of oil into spark 1.
plug hole. Crank engine a few times
and try to start again.
Tighten spark plug. If that does not 2.
work, replace spark plug. If problem
persists, may have head gasket
problem, see #3 to the left.
Tighten head. If that does not 3.
remedy problem, replace head
gasket.
Adjust valve clearance. If that does 4.
not work, clean or replace valves/
tappets.
Follow all safety precautions whenever diagnosing or servicing the
equipment or engine.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 19
Page 20
Troubleshooting (continued)
Problem Possible Causes Probable Solutions
Engine misres
Engine stops
suddenly
Engine knocks
Engine backres
Saw Blade not
rotating up to full
speed.
Poor quality of
cut.
Spark plug wire loose.1.
Incorrect spark plug gap or 2.
damaged spark plug.
Defective spark plug wire.3.
Old or low quality gasoline. 4.
Fuel tank empty or full of impure or 1.
low quality gasoline.
Defective fuel tank cap creating 2.
vacuum, preventing proper fuel ow.
Improper idle speed.3.
Faulty magneto, incorrect timing, or 4.
clogged carburetor.
Old or low quality gasoline. 1.
Engine overloaded. 2.
Incorrect spark timing, deposit 3.
buildup, worn engine, or other
mechanical problems.
Impure or low quality gasoline. 1.
Choke not open after engine warm. 2.
Engine not properly adjusted for 3.
high altitude operation.
Intake valve stuck, choke stuck, 4.
incorrect timing, clogged carburetor,
or overheated engine.
Improper fuel mixture.1.
Belt too tight or too loose.2.
Air lter needs cleaning or changing.3.
Blade improperly installed. 1.
Blade worn or damaged.2.
Check wire connections.1.
Re-gap or replace spark plug. 2.
Replace spark plug wire.3.
Use only fresh 90+ octane unleaded 4.
gasoline, 40:1 mixture with 2-stroke
engine oil.
Fill fuel tank with fresh 90+ octane 1.
unleaded gasoline in 40:1 mixture
with 2-stroke engine oil.
Test/replace fuel tank cap. 2.
Properly adjust idle speed.3.
Have qualied technician diagnose 4.
and service engine.
Empty fuel tank and re-ll with fresh 1.
90+ octane unleaded gasoline, 40:1
mixture with 2-stroke engine oil.
Do not exceed equipment’s load 2.
rating.
Have qualied technician diagnose 3.
and service engine.
Fill fuel tank with fresh 90+ octane 1.
unleaded gasoline, 40:1 mixture
with 2-stroke engine oil.
Move choke to RUN position after 2.
engine warms up.
Qualied technician must adjust 3.
engine at altitudes greater than
5,000 feet above sea level.
Have qualied technician diagnose 4.
and service engine.
Check that fuel mixture is accurate.1.
Adjust belt.2.
Check air lter and clean or replace.3.
Make sure Saw Blade is properly 1.
installed.
Replace worn or damaged Blade.2.
Follow all safety precautions whenever diagnosing or servicing the
equipment or engine.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 20
Page 21
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
PARTS LISTS AND DIAGRAMS
Drive System Parts List & Diagram
Part Description Qty
1A Back Cover 1
2A Flange Nut 2
3A Grommet 1
4A V-Belt SPZ 900 1
5A Belt Cover 1
Part Description Qty
6A Bolt 2
7A Belt Guard 1
8A Bolt 2
9A Pin 1
Note: When ordering parts for this component use the sufx “A”.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 21
Page 22
Blade Guard Assembly Parts List & Diagram
Part Description Qty
1B Washer 1
2B Washer 1
3B Washer 2
4B Guard Flange 1
5B Outside Flange 1
Part Description Qty
6B Inside Flange 1
7B Blade Guard 1
8B Adjustment Handle 1
9B Spacer 2
10B Bolt 2
Note: When ordering parts for this component use the sufx “B”.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 22
Page 23
Flange Assembly Parts List & Diagram
Part Description Qty
1C Hex Flange Bolt 3
2C Cutting Arm 1
3C Clamp 2
4C Ball Bearing 2
5C Bushing 2
6C Belt Tensioner 1
7C Spacer 1
8C Screw 1
9C Bracket 1
10C Bolt 1
11C Rubber Washer 1
Part Description Qty
12C Bolt 1
13C Arbor 1
14C Spring 4
15C Spacer 4
16C Bolt 4
17C Pulley 1
18C Washer 1
19C Nut 1
20C Hex Bolt 1
Note: When ordering parts for this component use the sufx “C”.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 23
Page 24
Clutch Assembly Parts List & Diagram
Part Description Qty
1D Spacer 1
2D Bushing 1
3D Clutch Drum 1
Part Description Qty
4D Clutch Washer 1
5D Centrifugal Clutch Assembly 1
Note: When ordering parts for this component use the sufx “D”.
Handle Assembly Parts List & Diagram
Part Description Qty
1E Bracket 1
2E Washer 8
3E Bolt 6
4E Roller Shaft 1
5E Bolt 2
Part Description Qty
6E Roller 2
7E Roller Screw 2
8E Front Handle 1
9E Washer 2
10E Bolt 2
Note: When ordering parts for this component use the sufx “E”.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 24
Page 25
Control System Parts List & Diagram
Part Description Qty
1F Bolt1 4
2F Washer 4
3F Handle Support 1
4F Screw 2
5F Front Vibration Isolator 4
6F Rear Vibration Isolator 2
7F Trigger 1
8F Throttle Spring Piece 1
9F Trigger Safety Lever 1
10F Throttle Catch Spring 1
11F Left Handle Cover 1
Part Description Qty
12F Screw 2
13F Tank Complete 1
14F Fuel Line 1
15F Tank Vent 1
16F Fuel Filter 1
17F Gas Cap 1
18F O-Ring 1
19F Pot Hook 1
20F Fuel Line Clamp 1
23F Gas Cap Complete 1
Note: When ordering parts for this component use the sufx “F”.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 25
Page 26
Air Filter Assembly Parts List & Diagram
Part Description Qty
1G Front Air Filter Cover 1
2G Washer 1
3G Bolt 1
4G Foam Filter 1
5G Air Filter Cover 1
6G Washer 6
7G Bolt 3
8G Seal 1
Part Description Qty
9G Air Filter Base 1
10G Bolt 3
11G Seal 1
12G Paper Filter 1
13G Filter Screen 1
14G ON/OFF Switch 1
17G Grommet 1
Note: When ordering parts for this component use the sufx “G”.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 26
Page 27
Carburetor Assembly Parts List & Diagram
Part Description Qty
1H Rubber Seal 1
2H Intake Manifold 1
3H Bolt 2
4H Gasket 1
5H Breather Hose 1
6H Choke 1
Part Description Qty
7H Carburetor Assembly 1
8H Throttle Linkage Holder 1
9H Throttle Bushing 1
10H Throttle Rod 1
11H Throttle Spring 1
Note: When ordering parts for this component use the sufx “H”.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 27
Page 28
Recoil Assembly Parts List & Diagram
Part Description Qty
1I Washer 4
2I Bolt 4
3I Air Conductor 1
4I Starter Cover 1
5I Recoil Spring Mount 1
6I Screw 4
7I Recoil Spring 1
8I Starter Pulley 1
Part Description Qty
9I Washer 1
10I Bolt 1
11I Starter Rope 1
12I Bafe 1
13I Starter Handle 1
15I Starter Assembly 1
16I Recoil Assembly 1
Note: When ordering parts for this component use the sufx “I”.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 28
Page 29
Ignition Assembly Parts List & Diagram
Part Description Qty
1J Flywheel Assembly 1
2J Washer 1
3J Washer 1
4J Nut 1
Part Description Qty
5J Ignition Assembly 1
6J Washer 2
7J Washer 2
8J Bolt 2
Note: When ordering parts for this component use the sufx “J”.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 29
Page 30
Cylinder Assembly Parts List & Diagram
Part Description Qty
1K Cylinder 1
2K Washer 4
3K Bolt 4
4K Spark Plug 1
5K Intake Manifold 1
6K Clamp 1
7K Cylinder Breather Hose 1
Part Description Qty
8K Holder 1
9K Washer 3
10K Bolt 2
11K Bolt 1
12K Gasket 1
13K Decompression Valve 1
14K Spring 1
Note: When ordering parts for this component use the sufx “K”.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 30
Page 31
Mufer Assembly Parts List & Diagram
Part Description Qty
1L Holder 1
2L Washer 3
3L Washer 2
4L Bolt 3
Part Description Qty
5L Deector 1
6L Mufer 1
7L Bolt 2
8L Gasket 1
Note: When ordering parts for this component use the sufx “L”.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 31
Page 32
Crankshaft Assembly Parts List & Diagram
Part Description Qty
1M Wrist Pin 1
2M Retaining Ring 2
3M Woodruff Key 1
4M Piston 1
Part Description Qty
5M Piston Ring 2
6M Crankshaft Assembly 1
7M Needle Bearing 1
Note: When ordering parts for this component use the sufx “M”.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 32
Page 33
Crankcase Assembly Parts List & Diagram
Part Description Qty
1N Gasket 1
2N Crankcase Left 1
3N Cover 1
4N Seal 1
5N Crankcase Ball Bearing 2
6N Washer 7
7N Bolt 2
Part Description Qty
8N Bolt 4
9N Bolt 1
10N Guide Pin 2
11N Crankcase Right 1
12N Grommet 1
13N Stud Bolt 2
14N Seal 1
Note: When ordering parts for this component use the sufx “N”.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 33
Page 34
Wet Cutting Kit Parts List & Diagram
Part Description Qty
1O Bolt 1
2O Washer 1
3O Water Valve Tubing 1
Part Description Qty
4O Tie Wrap 1
5O Quick Connect Hose Fitting 1
5
Note: When ordering parts for this component use the sufx “O”.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 66753 For technical questions, please call 1-800-444-3353. Page 34
Page 35
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet
high quality and durability standards, and
warrants to the original purchaser that this
product is free from defects in materials
and workmanship for the period of 90 days
from the date of purchase. This warranty
does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or
accidents, repairs or alterations outside
our facilities, criminal activity, improper installation, normal wear and tear, or to lack
of maintenance. We shall in no event be
liable for death, injuries to persons or property, or for incidental, contingent, special
or consequential damages arising from the
use of our product. Some states do not allow the exclusion or limitation of incidental
or consequential damages, so the above
limitation of exclusion may not apply to
you. THIS WARRANTY IS EXPRESSLY IN
LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY
AND FITNESS.
To take advantage of this warranty,
the product or part must be returned to us
with transportation charges prepaid. Proof
of purchase date and an explanation of the
complaint must accompany the merchan-
dise. If our inspection veries the defect,
we will either repair or replace the product
at our election or we may elect to refund
the purchase price if we cannot readily
and quickly provide you with a replacement. We will return repaired products at
our expense, but if we determine there is
no defect, or that the defect resulted from
causes not within the scope of our warranty, then you must bear the cost of returning
the product.
This warranty gives you specic legal
rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box
6009 • Camarillo, CA 93011 • (800)
444-3353
EMISSION CONTROL
SYSTEM WARRANTY
California and United States Emission Control
Defects Warranty Statement
The California Air Resources Board (herein CARB), the United
States Environmental Protection Agency (herein EPA), and Harbor
Freight Tools (herein HFT) are pleased to explain the emission control system warranty on your 1995 and later Small Off-Road Engine
(herein engine). In California, the engine must be designed, built
and equipped to meet the State’s stringent anti-smog standards.
Elsewhere within the United States, new off-road, spark-ignition
engines certied for model year 1997 and later, must meet similar
standards set forth by the EPA. HFT must warrant the emission
control system on your engine for the periods of time described
below, provided there has been no abuse, neglect or improper
maintenance of your engine.
Your emission control system may include parts such as the
carburetor or fuel-injection system, and the ignition system. Also
included may be hoses, belts, connectors and other emissionrelated assemblies.
Where a warrantable condition exists, HFT will repair your
engine at no cost to you including diagnosis, parts and labor.
Manufacturer’s Warranty Coverage
The 1995 and later engines are warranted for two (2) years.
If any emission-related part on your engine is defective, the part
will be repaired or replaced by HFT.
Harbor Freight Tools Emission Control Defects
Warranty Coverage
Engines are warranted for a period of two (2) years relative to
emission control parts defects, subject to the provisions set forth
below. If any emission related part on your engine is defective, the
part will be repaired or replaced by HFT.
Owner’s Warranty Responsibilities
As the engine owner, you are responsible for the performance •
of the required maintenance listed in your Owner’s Manual.
HFT recommends that you retain all receipts covering main-
tenance on your engine, but HFT cannot deny warranty
solely for the lack of receipts or for your failure to ensure the
performance of all scheduled maintenance.
As the engine owner, you should, however, be aware that •
HFT may deny you warranty coverage if your engine or a part
has failed due to abuse, neglect, improper maintenance, or
unapproved modications.
You are responsible for shipping your engine to a HFT war-•
ranty station as soon as a problem exists. Contact the HFT
Customer Service department at the number below to make
shipping arrangements. The warranty repairs should be
SKU 66753 For technical questions, please call 1-800-444-3353. Page 35
Page 36
completed in a reasonable amount of time, not to exceed
30 days.
If you have any questions regarding your warranty rights
and responsibilities, you should contact the Harbor Freight Tools
Customer Service Department at 1-800-444-3353.
Harbor Freight Tools Emission Control Defects
Warranty Provisions
1. Length of Coverage
HFT warrants to a rst retail purchaser and each subsequent
purchaser that the engine is free from defects in materials
and workmanship that cause the failure of warranted parts
for a period of two (2) years after the date of delivery to the
rst retail purchaser.
2. No Charge Repair or Replacement
Repair or replacement of any warranted part will be performed
at no charge to the owner if the work is performed through a
warranty station authorized by HFT. For emissions warranty
service, contact the HFT Customer Service Department at
1-800-444-3353.
3. Consequential Damages Coverage
Coverage under this warranty shall also extend to the failure
of any engine components caused by the failure of any war-
ranted part while it is still covered under this warranty.
4. Coverage Exclusions
Warranty claims shall be led in accordance with the provi-
sions of the HFT warranty policy explained in the box at the
top of the previous page. HFT shall not be liable for any loss
of use of the engine, for any alternative usage, for any damage
to goods, loss of time, or inconvenience. Warranty coverage
shall also be excluded for any part which fails, malfunctions,
or is damaged due to failure to follow the maintenance and
operating instructions set forth in the Owner’s Manual includ-
ing, but not limited to:
Use of parts which are not authorized by HFTa)
Improper installation, adjustment or repair of the engine b)
or of any warranted part unless performed by an authorized warranty center
Failure to follow recommendations on fuel use contained c)
in the Owner’s Manual
Improper or inadequate maintenance of any warranted d)
parts
Repairs performed outside of the authorized warranty e)
service dealers
Alterations by changing, adding to or removing parts f)
from the engine.
5. Service and Maintenance
Component parts which are not scheduled for replacement
as required maintenance or are scheduled only for regular
inspection to the effect of “repair or replace as necessary”
are warranted for the warranty period. Any warranted part
which is scheduled for replacement as required maintenance
is warranted for the period of time up to the rst scheduled
replacement point for that part. Any replacement part, pro-
vided it is equivalent in durability and performance, may be
used in performance of maintenance or repairs. The owner
is responsible for commissioning a qualied technician/me-
chanic to perform all required maintenance, as outlined in
the Inspection, Cleaning, and Maintenance section in this
manual.
6. Warranted Parts
1) Fuel Metering System
Carburetor and its internal parts.i)
Fuel pump (if so equipped).ii)
Cold start enrichment system.iii)
2) Air Induction System
Intake pipe/manifold.i)
Air cleaner.ii)
3) Ignition System
Spark plug.i)
Magneto ignition system.ii)
4) Catalyst System (if so equipped)
Exhaust pipe stud.i)
Mufer.ii)
Catalytic converter (if so equipped).iii)
5) Miscellaneous Items Used in Above Systems
Vacuum, temperature and time sensitive valves i)
and switches.
Hoses, belts, connectors, and assemblies.ii)
SKU 66753 For technical questions, please call 1-800-444-3353. Page 36
Loading...