Cherry Aerospace H753A-275NP, H753A-280NP, H753A-249NP, H753A-280NP-2.1 Technical Data Sheet
1224 East Warner Ave,
TS-H7
53A-275
NP Rev:
-
Date: 0
6/03/08D
CR: 0
8-0734
H753A-275NP
Fig
ure
1
RIVETLESS NUT PLATE® RIGHT ANGLE PULLING HEAD
Technical Data Sheet, Page 1 of 2
DIMENSIONAL DATA
(see figure, all measurements in Inches)
Tool weight (without riveter): 1.20 Lbs (0.540 Kg).
CHOICE OF RIVETERS
G704B Cherry® Riveter
G750A Cherry® Hand Riveter with adaptor
750A-088
MOUNTING INSTRUCTIONS
Attach riveter to air source for correct piston
positioning; for hand powered riveters (G750A),
make sure that the pressure has been released
and that the correct adaptors are used.
Push the collet bolt assembly forward (see Figure
1) before mounting.
While holding collet bolt in a forward position,
engage 1 or 2 threads of drawbolt (18) onto
riveter head piston before threading adapter
fitting (19) into end of riveter head cylinder; turn
clockwise until snug.
Rotate pulling head to desired position and
tighten jam nut (20) to secure pulling head orientation.
Cycle the tool to make sure it is functional.
USAGE
The H753A-275NP pulling head has been specifically developed for installations of CNP 53; a carbon
composite structure application of Cherry® Rivetless NutPlate. This right angle pulling head is used in
constrained applications where straight pulling head H704-275NP is too large.
BEFORE USE, MAKE SURE THAT:
Proper air source is connected.
The sleeve and pilot are in proper working condition; any sign of damage is an indication that
components need to be replaced. No installations should be made if tooling is worn or damaged.
DURING OPERATION
Inspect the active area of the sleeve and pilot regularly.
Keep the tool clean, especially the pilot, sleeve and jaws; pay special attention when sealants are used.
If stem slippage occurs, the jaws need to be either cleaned or replaced.
PREVENTATIVE MAINTENANCE
Clean the sleeve, pilot, jaw set and collet every 1,000 installations or when failures occurs; use a wire
brush to clean the copper deposited inside the jaw set.
Lubricate outside of the jaw set with Lubriplate® or similar light lubricant.
Santa Ana, Ca 92705
Tel: 1-714-545-5511
www.cherryaerospace.com
1224 East Warner Ave,
TS-H7
53A-275
NP Rev:
-
Date: 0
6/03/08D
CR: 0
8-0734
H753A-275NP
12345
678910
111112
13
13
141415
151617
18
19
20
9
753B5
LEVER
1
7
975-019
FRAME
1
1
975-016
SLEEVE
1
ITEM
PART
QTY.
WARRANTY
For more information please contact our Technical Services Department at tel. 714
-
850-6022
W
HEN
RE-ASSEMBLING
:
RIVETLESS NUT PLATE® RIGHT ANGLE PULLING HEAD
Technical Data Sheet, Page 2 of 2
PARTS LIST
20 671A16 JAM NUT 1
19 975-020 ADAPTER FITTING 1
18 975-021 DRAWBOLT 1
17 753A11 GUIDE PIN 1
16 753B6 BELL CRANK 1
15 753A9 LINK PIN 4
14 P-954 LINK 8
13 753A10 PIVOT PIN 2
12 753A16 GUARD 1
11 P-930 SET SCREW 2
10 P-413 BUTTON HEAD SCREW 1
8 975-018 COLLET BOLT 1
6 P-1319 SPRING 1
5 975-017 JAW FOLLOWER 1
4 975-014 JAW SET 1
3 753A13A COLLET 1
2 975-015 PILOT INSERT 1
No.
NUMBER
GENERAL / TECHNICAL QUESTIONS
1224 E. Warner Avenue
Santa Ana, CA 92705 USA
1-714-850-6022 (Phone)
1-714-850-6093 (Fax)
LOCTITE®is a registered trademark of Henkel Corporation.
LUBRIPLATE® is a registered trademark of Fiske Brothers Refining Co.
Seller warrants thegoods conform to applicable specifications and drawings and will be manufactured and inspected according to generally accepted practices of companies manufacturingindustrial or aerospace
fasteners. In the event of any breach of the foregoing warranty, Buyer’s sole remedy shall be to return defective goods (after receiving authorization from Seller) for replacement or refund of the purchase price, at
the Seller’soption. Seller agrees to any freight costs in connection with the return of any defective goods, but any costs relating to removal of the defective or nonconforming goods or installation of replacement
goods shall be Buyer’s responsibility.SELLER’S WARRANTY DOES NOT APPLY WHEN ANY PHYSICAL OR CHEMICAL CHANGE IN THE FORM OF THE PRODUCT IS MADE BY BUYER. THE
FOREGOING EXPRESS WARRANTY AND REMEDY ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES; ANY IMPLIED WARRANTYAS TO QUALITY, FITNESS FOR PURPOSE, OR
MERCHANTABILITY IS HEREBY SPECIFICALLY DISCLAIMED AND EXCLUDED BY SELLER. This warranty is void if seller is not notified in writing of anyrejection of the goods within ninety (90) days after receipt
of the goods by buyer.
Seller shall not be liable under any circumstances for incidental, special or consequential damages arising in whole or in part from any breach by Seller, AND SUCH INCIDENTAL, SPECIAL, OR CONSEQUENTIAL
DAMAGES ARE HEREBY EXPRESSLY EXCLUDED.
Our policy is one of continuous development. Specifications shown in this document may be subject to changes introduced after publication.
NOTE: The properties, strength, dimensions, installed characteristics and all other information in these materials are for guidance only to aid in the correct selection
of the products described herein and is not intended or implied as part of the above warranty. All applications should be evaluated for functional stabilityand available
samples of the described parts can be requested for installed tests, suitability and evaluations.
DESCRIPTION
PER
- Lubricate outside of pilot insert with o-ring
lubricant or eqiovalent.
- Oil or grease heavily all sliding surfaces with
Lubriplate® or equivalent.
- Use Loctite® 242 (removable) on sleeve and
collet threads.
Santa Ana, Ca 92705
Tel: 1-714-545-5511
www.cherryaerospace.com
Loading...