H1 manual
Bluetooth play/communicate
pairing, again press key 3
Hunting/AUX power switch Hunting Vol +
Hunting: short press button -> Power
AUX: short press button --> Power On/Off.
BT On：Press key 2 seconds until red/blue
lamp flashing or blue lamp flashing.
BT Off：Press key 5 seconds until red/blue
lamp to off (last only flashing once)
Music play: press key -> play/stop music
Receive call：press this key for receiving
phonecall
Off call： when communication, press this
key to cut off call
Redial：double click this key, last redial
in phone
press key 2 seconds,
environment volume
will be increased
Hunting Vol -
press key 2 seconds,
environment volume will be
decresed
Bluetooth Vol +Bluetooth Key
press key 2 seconds,
volume will be increased
BT next song key
press this key to play next
song of BT
Reject call: press key 2 sec.
,
BT previously song key
BT play：press this key,
previously song play
BT open/reconnect：no music, no
communicate, press key 3
seconds, then cut off BT
seconds, re-connect BT pairing.
BT/Charging LED indicator
Bluetooth Vol -
press key 2 seconds,
Bluetooth play/communicate,
volume will be decreased
3.5mm AUX socket
Micro-USB charging socket
AUX IN socket, plug
5mm external sound source, press
then power on
this mode is controlled by external sound
can reconnect pairing previously mobile
Bluetooth microphone
Battery compartment
Operation manual
Hunting :
press on hunting，press VOLUME+ 2 seconds, environment volume be increased，press VOLUME- 2 seconds,
environment volume be decreased，when environment noise too big, will cut off the sound. Again press then off
hunting。Hunting & Aux can be alive，hunting can work when BT play music / communicate
AUX：
source 。AUX can work with hunting at the same time. When BT play music or communicate, AUX will stop work，when BT
stop play music or communicate, AUX is work again.
3.
，
BT operate：
press 2 seconds to open ，if already pairing mobile，then BT is connected automatically, and BT blue lamp is
flashing. If no pairing mobile，then BT is into pairing mode, and LED is alternative flashing。Close BT work is
pressing 5 seconds，until LED red/blue light flash 1 time then off light, then BT is off work.
BT pairing：
For pairing, BT's LED red/blue light is alternative flashing (in pairing status)，use mobile to search headphone name
"H1" then connect. Pairing OK the BT blue light is flashing in case pairing success。If unpairing 10 minutes，BT will
close automatically。When no music, no communicate, press
.
BT music play：
After BT pairing，press can start to play music，press key again then stop to play music。Press VOL+ key 2 seconds
then increase volume level，press VOL- key 2 second then reduce volume level. Press
◀
3 seconds can stop BT pairing，again press ◀ 3 seconds
◀
play previously song，press
▶
BT commuincate：
radiate radio frequency energy and, if not installed and used in accordance with the instructions
p
pq
p
Income call, press can receive，press ▶ 2 seconds, reject income call. When commuincate, press VOL+ key 2 seconds
increase volume level，press VOL- key 2 seconds can reduce volume level。No communicate, double click ，mobile will
Lithium battery charging:
Set the power off before charging battery，use 5Vdc / 500mA adapter to plug in Micro-USB of unit to charge. Red LED is
long bright when charging battery，when charging is fully capacity then Red LED is off bright。
Battery:DC 4.5V, or DC 3.7V, or DC 5V (only for charging by USB port)
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital,
pursuant to Part 15 or the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
may casue harmful interference to radio communications, However, there is no guarantee that
interference will not occur in a particular installation. If the equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
--- Reorient or relocate the receiving antenna.
--- Increase the se
aration between the equipment and receiver.
--- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
--- Consult the dealer or an experienced radio/ TV technician for help.
,
FCC Radiation Exposure Statement:
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition w
ithout RF striction.
Loading...