Cheng Uei Precision Industry Hshu Branch H505 User Manual
Quick Start Guide
H505
Bluetooth®
Handsfree Headset
Get Connected in
4 Quick Steps
1 - CHARGE
2 - START
BLUETOOTH
3 - PAIR
4 - TEST AND
USE
BEFORE YOU
BEGIN
Before using this product, read the Important Safety and Legal
Information included in your phone's user's guide, and follow
its instructions
Take a moment before you get started to
familiarize yourself with your new
H505 Handsfree Headset.
Ear Piece
Microphone
Volume
Buttons
Call Button
LED
Indicator
Light
1
Charge your headset for 2 hours:
Plug the Motorola charger into the top of
1
the headset with the release tab facing up.
The LED indicator light turns on when the
device is charging. It may take up to 1
minute for the LED to turn on. When the
device is fully charged (about 2 hours), the
LED indicator turns off.
Disconnect the charger.
2
CHARGE
Your Headset
START BLUETOOTH
2
Feature
Your Headset
Your phone's Bluetooth feature is off by default.
To use your headset, the Bluetooth feature
must be turned on in your phone.
For most Motorola phones:
M
Select (Menu) > Settings > Connection >
1
Bluetooth Link > Setup.
Scroll to Power.
2
3
Select Change.
Scroll to On.
4
Press Select to turn on Bluetooth.
5
Bluetooth remains on until you turn the
feature off.
Note: These steps are for most Motorola phones. For other
phones, see your phone's user's guide.
3
Before you can use your headset, you must pair
(link) it with your phone.
Step A - PUT THE HEADSET IN PAIRING
MODE
With the headset power off, press and hold
1
the Call button for 4 to 5 seconds and then
release.
The power turns on and the headset goes
into pairing mode. When the headset is in
pairing mode, the LED indicator light turns
on and remains steadily lit.
If the LED indicator light is flashing or does
2
not remain steadily lit, repeat these steps.
PAIR
Your Headset
Call Button
LED Indicator Light
Motorola, Inc.
Consumer Advocacy Office
1307 East Algonquin Road
Schaumburg, IL 60196
www.hellomoto.com
1-877-MOTOBLU
1-800-331-6456 (United States)
1-888-390-6456 (TTY/TDD United States for
hearing impaired)
1-800-461-4575 (Canada)
Guide Number: <TBD>
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. The Bluetooth trademarks are
owned by their proprietor and used by Motorola, Inc. under
license. All other product or service names are the property of
their respective owners. © Motorola, Inc. 2005.
3
Step B - SET THE PHONE TO LOOK FOR
YOUR HEADSET
For most Motorola phones:
On your Motorola phone, select (
1
PAIR CONTINUED
Your Phone
M
Menu) >
Settings > Connection > Bluetooth Link >
Handsfree > Look for Devices.
The phone lists all Bluetooth devices it
finds.
2
Select Motorola H505.
Select OK or Yes to pair (bond) the
3
handsfree device.
4
Enter the passkey: 0000
Select OK.
5
When your device is successfully paired
with your phone, the LED indicator light
changes from steadily lit to flashing.
Note: These steps are for most Motorola phones. For other
phones, see your phone's user's guide.
4
Your phone and headset are now paired
and ready to make and receive calls.
To confirm they are successfully paired and
operating properly, make a call:
Open the ear piece and place over your ear.
1
On your phone, dial the number you want
2
to call.
Press Send to make the call. If your phone
3
and headset are successfully paired, you
will hear ringing.
After you have successfully paired your
phone and headset, you do not need to
repeat these steps.
TEST AND USE
USING YOUR H505
See Quick Use on the
reverse side of this guide
for information on
using your H505
TROUBLESHOOTING
My phone does not find my headset
Make sure your headset is in pairing mode
before looking for devices on your phone
(see step 3).
My headset worked before but now it's
not working.
Make sure your phone is on and the Bluetooth
feature is turned on in your phone (step 2). If
the Bluetooth feature has been turned off or
was turned on only temporarily, you may need
to restart the Bluetooth feature (see step 2) and
pair your phone and headset again (see step 3).
Support.
If you need more help, contact us at
1- 877-MOTOBLU.
040067o
Quick Use
H505
Bluetooth®
Handsfree Headset
IMPORTANT:
Be sure to first follow the
Quick Start Guide
on the reverse side
of this guide
to complete initial setup
of your H505.
TURNING ON AND OFF
To turn your headset on, press the Call
button. The LED indicator light flashes when
the power is on.
To turn you headset off, press the Call
button. The LED indicator light turns off
when the power is off.
Call
Button
CHANGING FOR
LEFT EAR WEAR
You can wear your H505 headset on your left or
right ear. The headset comes ready for the right
ear. To change the headset for the left ear:
Open the ear hook 90
1
degrees from the
headset.
Gently lift and pull the
2
top of the ear hook up
and off the upper hinge
pin. Then, pull it away to
remove it.
Flip the headset over.
3
4
Hook the bottom of the
ear hook onto the lower
3
hinge pin, then lift and
pull the top of the ear
hook over the upper
4
hinge pin.
040059o
1 Open Ear Hook
2 Pull Ear Hook Up
040059o
CHANGING VOLUME
BUTTON ORIENTATION
If you change your headset for left ear wear,
you can also change the orientation of the
volume buttons.
Turn the headset power off.
1
Press the Call button and the volume
2
button you want to assign as the
"volume up" button until the LED
indicator light flashes twice.
The headset power turns on.
Call Button
WEARING THE
HEADSET
Open the ear piece.
1
Loop the ear piece over your ear.
2
Position the microphone as necessary.
3
4
Press the headset to your ear.
FOR MORE INFORMATION ON USING
YOUR MOTOROLA H505
Visit us at www.hellomoto.com/bluetooth and
click Support.
SUPPORT
If you need more help, contact us at
1- 877-MOTOBLU.
MAKING CALLS
To make a voice dial call, short press the Call
button and speak the name.
To end a call, short press the Call button.
To put an active call on hold, long press the
Call button.
To resume a call on hold, long press the Call
button.
To receive a call, short press the Call button.
To reject a call, long press the Call button.
To answer a second incoming call, long
press the Call button (places first call on hold).
To toggle between two active calls, long
press the Call button.
To transfer a call from the phone to
headset, short press the Call button.
Note: Your H505 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which
profile your phone supports. See your phone's user's guide
for more information.
MUTING A CALL
To mute a call, press both volume buttons.
Volume
Buttons
LED INDICATOR LIGHTS
The LED indicator light provides information
about your headset status.
With the Charger Plugged In
Headset Indicator Headset Status
Off Charging in progress
On (steady) Charging complete
With No Charger Plugged In
Headset Indicator Headset Status
Off Power off
On (steady) Pairing mode
10 rapid flashes Pairing successful
Pulsing (2 seconds
on, 6 seconds off) Connected (on a call)
Flashing (.1 second on,
2.9 seconds off) Standby (not on call)
AUDIO TONES
The audio tones provide information about your
headset status.
Audio Tone Headset Status
Single high tone when Volume minimum or
pressing volume button maximum reached
Five rapid high tones Low battery
repeated every 20 sec.
No audio indications; Out of range
detereriorating audio
quality
Series of 4 tones, low Audio link open
to high (headset mode)
Active call
(handsfree mode)
Ring tone Incoming call
Single high tone Pairing confirmation
Single low tone Voice activation
Dual high/low tone Voice tag not
recognized
Single high tone End call
Loading...