Cheng Uei Precision Industry VFBTHSFLK001 User Manual
MN X-22O 1_User Guide
Button
Headset
status
Action
Function
Ringing
Short Press
Answer an incoming call
Talking
Short Press
Hang up an active call
Idle
Short Press
Voice Recognition
Talking
Press and hold
for longer than 2
seconds
MIC mute/un-mute
Ringing
Press and hold
for longer than 2
seconds
To reject the i ncoming call
Idle
Press and hold
for longer than 3
seconds
To redial last number
Talking
Press and hold
for longer than 3
seconds
Audio Transfer from the phone
to the headset during a call
Power off
Press and hold
for longer than 5
seconds
Put Headset into pairing mode when
the headset’s state is not connected
MFB
Power on
Press and hold
for longer than 5
seconds
Power off the headset
Vodafone Bluetooth Headset
VF-BTHS-FLK-001
Quick Guide
Button function
60mm
FCC Statement
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) These devices may not
cause harmful interference, and (2) these
devices must accept any interference
received, including interference that may
cause undesired operation.
European Union Notice
This device is compliance with the R&TTE
Directive (99/5/EC) and conformity to the
following European Norms:
EN 300 328
EN 301 489-01
EN 301 489-17
The crossed-out wheeled bin
means that within the European
Union the product must be taken to
separate collection at the product
end-of-life. Do not dispose of these
products as unsorted municipal
waste.
Overview
Front
MFB (Main Function Button)
Back
Charging connector
LED
Eve nt
#
Pow er on
1
2
Pow er off
Pai ring
3
Sta ndby - No
4
Con necte d
Sta ndby - ACL
5
con necte d
SCO
6
Con necte d
Cha rging
7
Cha rging
8
Com plete
Charging
First time use: Charge the headset for
approximately 2 hours, or until the LED
light is off
Step 1.
Connect the mini
connector of
charging cable to
the charging
connector on the
headset
Ear hook
Step 2.
Connect the USB
connector of
chargeing cable
to the powered
USB port on the
desktop or laptop.
Speaker
Step 3.LED will flash twice when connected and lights
on during charging. After charging complete, LED will
Microphone
turn off.
Note: Headset is not functional while charging.
LED Flashing Requirements
(LE D1 and LE D2)
Fla shing P atter n
Fla sh 3 time s
ON (2 50ms)
OFF ( 250ms )
Fla sh 3 time s
ON (2 50ms)
OFF ( 250ms )
ON( 300ms )
OFF (300m s)
ON( 100ms )
OFF (4900 ms)
ON( 100ms )
OFF (2900 ms)
ON( 100ms )
OFF (1900 ms)
ON
OFF
Onl y appli ed when u ser pow ers
on th e syste m.
Onl y appli ed when u ser shu ts
dow n the sys tem.
If an y mobil e devic es pair ed
exi sts, he adset w ill do au to
con necti on firs t. After a uto
con necti on, the n pairi ng
fun ction w ill be wo rkabl e
COM MENT
N/A
N/A
N/A
N/A
N/A
360m m
How to use
Power on / off:
Press and hold the MFB for longer than 5 seconds to switch
Pairing:
Before you can use your headset, you must pair it with your
phone
Step 1.Power on the headset
Step 2. Turn on the Bluetooth function on the mobile phone
and set the phone to search for Bluetooth devices.
Step 3.Select the headset (VF-BTHS-FLK-001)
Step 4.Enter the passcode 0000 to pair and connect the
headset to your phone.
Answering / Ending a call:
Short press the MFB
Rejecting an incoming call:
Press and hold for longer than 2 seconds
Redialing last number:
Press and hold for longer than 3 seconds
Turning the microphone on/off
during a call:
Press and hold for longer than 2 seconds
Sound Indicator Specification
#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Act ion
Rin g tone
Pow er ON
Pow er OFF
Tra nsfe rA udio
Low B atter y
Pai r Fail
SLC (ACL) C onnec ted
SLC (ACL) D iscon necte d
Toggl e Mute
End O f Call
Voic e Dial
Las t Numbe r Redia l
Ans wer
Rej ect
Can cel/E nd
Err or
TROUBLESHOOTING
If you phone cannot connect to the headset, do as
follows:
• Ensure that the headset is charged, powered on, and
paired with and connected to your phone.
• Ensure that the Bluetooth feature is activated on your
phone.
• Check that the headset is within 10 meters (30 feet)
without obstructions.
If your headset is automatically powered off, do
as follows:
•The battery is too low. Please charge the headset.
Safety Precautions
Do not place in heat sources such as radiators, heat registers,
．
stoves, or other products that produce heat
Do not use the product in a wet location. If your device does get
．
wet, allow it to dry completely.
Do not attempt to open the device.
．
Do not drop, knock, or shake the device. Rough handling can
．
break internal circuit boards and fine mechanics.
Do not use harsh chemicals, cleaning solvents, or strong
．
detergents to clean the device.
Do not use the incorrect external power source to charge.
．
All of the above precautions apply equally to
your device, battery, charging cable.
Sou nd play ed
Rin g_val kyrie s
4 Not e Risin g Scale ( 150ms G S4
DS5 G S5 C6)
4 Not e Faili ng Scal e (150m s C6
GS5 D S5 Gs4)
V Lon g High (8 00ms G6 )
Lon g High (5 00ms G6 )
Lon g Low (50 0ms G5)
Sho rt Midd le (100 ms Gs7)
Sho rt High ( 100ms G 6)
2 Not e Risin g Scale ( 200ms E 6A 6)
2 Not e Falli ng Scal e (300m sA 6 E6)
Lon g Middl e (500m s Gs7)
Lon g Middl e (500m s Gs7)
2 Not e Risin g Scale ( 200ms E 6A 6)
2 Not e Falli ng Scal e (300m sA 6 E6)
2 Not e Falli ng Scal e (300m sA 6 E6)
Lon g Low (50 0ms G5)
m
10m
1
Loading...