Page 1
Boiling Point
Liquid
Aerosol
108 F/42 C
118oF/48oC
Evaporation Rate
(butyl acetate=1)
>1
Flash Point (TCC)
None
Specific Gravity
Liquid
Aerosol
1.26
1.22
Vapor Pressure @68F
Liquid 405 mmHg
Aerosol 175mmHg
Appearance Clear, colorless liquid
Odor
Mild
Solubility in Water
Negligible
Dielectric Breakdown
(ASTM D-877)
Liquid
Aerosol
32 kV
8kV
Kauri-Butanol
(KB) Number
128
Shelflife Aerosol - 5 years from DOM
Liquids - 2 years after opening
VOC* Content: Liquid Aerosol
CARB 100% 73%
SCAQMD 1138 g/L 854g/L
Federal 90% 70%
Technical Data Sheet
Max-Kleen™ Tri-V
The extra-strength, nonflammable cleaner with high dielectric
TDS # VVV2279
PRODUCT DESCRIPTION
Max-Kleen™ Tri-V is ideal for removal of all types
TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES
of soils including oxidized oil and grease from
electronic / electrical motors and relays. Tri-V nPB
replacement chemistry is a novel new chemistry
that does not contain any n-propyl bromide, TCE,
any hazardous air pollutants or ozone depleting
compounds. It is the ideal solvent for most
electronic / electrical applications. This extrastrength cleaner evaporates quickly without leaving
a residue behind.
Quickly removes all types of tough soils
including oxidized oil and grease
Best product for electrical applications
Dielectric strength of >30 kV (liquid)
Does not contain n-propyl bromide,
trichloroethylene, perchloroethylene, HAP’s, or
any ozone depleting compounds
Nonflammable, no flash point
Stabilized for metals such as aluminum,
magnesium, titanium, and brass
Noncorrosive, safe for sensitive metals
Leaves no residue
TYPICAL APPLICATIONS
Max-Kleen™ Tri-V can be used for all repair,
maintenance, and manufacturing applications
including:
Removes grease, oil, lubricants, wax and tar
Cleans contacts, relays and switches, circuit
breakers and fuse blocks
All repair and maintenance cleaning including:
controls, conveyors and gear drives controllers
Cleans electric motors and logic controllers
COMPATIBILITY
Max-Kleen™ Tri-V is compatible with most metals. As
with any solvent, compatibility with plastics should be
determined on a non-critical area prior to use. Materials
such as polystyrene, ABS, polycarbonate and PVC are
not compatible with the cleaning solvent in Max-Kleen™
Tri-V.
*Volatile Organic Compound (VOC) information is calculated on a
weight basis using the VOC definition of California Air Resources
Board (CARB) Consumer Product Regulations, South Coast Air
Quality Management District (SCAQMD) Rule 102 and the Federal
definition published in 40 CFR 51.100(s).
Page 2
Material
Compatibility
ABS
Non-Compatible
Buna-N
Fair
EPDM
Fair
Graphite
Excellent
HDPE
Excellent
LDPE
Good
Lexan
Poor
Neoprene
Fair
Noryl
Poor
Nylon 66
Excellent
Cross-Linked PE
Excellent
Polypropylene
Excellent
Polystyrene
Non-Compatible
PVC
Excellent
Silicone Rubber
Poor
Teflon
Excellent
Viton
Fair
Performance
Soil Removal – Vapor Degreasing
Lubrizol Corrosion Inhibitor
100% Removal
Unilube All Purpose Grease
91.3% Removal
5W30 Synthetic Oil
100% Removal
Fire Resistant Hydraulic Fluid
100% Removal
Chain Lubricant
100% Removal
Silicone Fluid
100% Removal
Soil Removal – Ultrasonic Cleaning
Lubrizol Corrosion Inhibitor
100% Removal
Unilube All Purpose Grease
100% Removal
5W30 Synthetic Oil
100% Removal
Fire Resistant Hydraulic Fluid
100% Removal
Chain Lubericant
100% Removal
Silicone Fluid
100% Removal
ultrasonic or soak applications, be sure to cover
DISTRIBUTED BY:
tank when not in use to prevent evaporation.
As with all vapor degreaser equipment and processes, observe all
safety precautions, guidelines and operating rules associated with
these units. Failure to do so may put operations personnel at
risk. Avoid excessive vapor losses, loss of refrigeration, excessive
boil sump heat, etc. Make sure all equipment is operated in
accordance with the manufacturer’s guidelines and instructions. If in
doubt, contact your manufacturer immediately.
Soak applications - Allow the soiled article to soak in
Max-Kleen™ Tri-V for 5 - 10 minutes, then remove and
loosen any remaining soils with a ControlwipesTM Wipe.
For wipe applications, wet a Controlwipes™ Wipe with
Max-Kleen™ Tri-V and wipe away soils.
TECHNICAL & APPLICATION
ASSISTANCE
Chemtronics provides a technical hotline to answer
your technical and application related questions.
The toll free number is:
1-800-TECH-401.
AVAILABILITY
VVV2279 20oz aerosol
VVV179 1 gallon liquid
VVV579 5 gallon liquid
VVV5579 53 gallon liquid
NOTE:
This information is believed to be accurate. It is intended for
professional end users having the skills to evaluate and use the
data properly. CHEMTRONICS does not guarantee the
accuracy of the data and assumes no liability in connection
with damages incurred while using it.
Chemtronics is a registered trademark of Chemtronics. All rights
reserved. Max-Kleen, Tri-V
of Chemtronics. All rights reserved.
All other trademarks herein are trademarks or registered
trademarks of their respective owners.
™
and Controlwipes are trademarks
USAGE INSTRUCTIONS
Read MSDS carefully prior to use.
For aerosol usage - Spray 4-6 inches from surface to
clean. Wash parts from top to bottom, allowing the
liquid to flush away dissolved soils. For precise
application use attached extension tube.
For vapor degreasing or ultrasonic cleaning
application, charge sump tank with solvent. For
Loading...