Page 1
Temperature No Clean
000078
Size #
Width
Inches
Color
Width
Metric
TDS # SWPbFree
CHEMTRONICS
Technical Data Sheet
Soder-Wick Lead-Free SD Desoldering Braid
PRODUCT DESCRIPTION
Soder-Wick Lead-Free is the state of the
art in desoldering technology. It is specially
designed for removal of today’s high
temperature lead-free solders. The single
layer weave used for Soder-Wick
LeadFree braid is lighter in mass than any other
desoldering braid available and allows for
lead-free solder removal at lower
temperatures. Soder-Wick
Lead-Free
responds faster than any other conventional
desoldering braid. This unique design
minimizes overheating and requires less
“contact” time thus preventing heat damage
to the PCB and sensitive components. For
Lead-Free rework, Soder-Wick
has the
answer.
Fastest wicking and heat transfer
High capacity for solder uptake
Halide free, no corrosive residues
Minimizes risk of hea t damage to pads,
components and PBCs
Can be used with Tin/Lea d solders
RoHS compliant
TYPICAL APPLICATIONS
Soder-Wick
Lead-Free desoldering braid
safely removes solder from :
Thru-hole Components
SMT Pads and BGA Pads
Micro Circuits
Terminals, Lugs and Posts
Identification Script
TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES
Flux Type High-
Type ROL0
Specifications: ANSI/IPC J STD-004
MIL-F-14256 F
No Clean Flux Spe c: MIL-STD-883B
Bellcore TR-NWT ANSI/IPC J SF818
Shelflife: 2 years
2 .060” Yellow 1.5 mm
3 .080” Green 2.0 mm
4 .110” Blue 2.8 mm
STATIC DISSIPATIVE PACKAGING
Soder-Wick
Lead-Free is packaged on
Static Dissipative bobbins to minimize the
risk of damage associated with static
electricity. The static dissipative bobbins
qualify as electrostatic discharge protective
per MIL-STD-1686C and MIL-HDBK263B and meet the static delay rate
provision of MIL-B-81705C.
Page 2
USAGE INSTRUCTIONS
Part #
Size
5 feet
10 feet
40-2-5
40-2-10
2
40-3-5
40-3-10
3
40-4-5
40-4-10
4
VacuPak Packaging
Part #
Size
The VacuPak Can contains ten
SW14025
2
SW14035
3
SW14045
4
For industrial use only.
Read MSDS care fully prior to use.
1) Choose a Soder-Wick Lead-Free braid width
equal to or slightly larger than the pad or
connection.
2) Choose a solder iron tip equal to or slightly
larger than the pad or connection.
3) Set temperature of iron between 650° and 750°F
4) Place wick on solder joint or pad and place tip
of hot iron on top of wick
5) As solder becomes molten, the color of the wick
will change from copper to silver.
6) Remove wick and iron simultaneously once
color change has stopped.
7) The component lead / pad is now clean and free
from solder.
8) Clip and discard the used portion of the wick.
9) If needed, clean PCB with CircuitWorks Lead-
Free Flux Remover Pen CW9400 and remove
soils with a ControlWipes absorbent wipe.
SODER-WICK IS DESIGNED TO MEET
OR EXCEED THE FOLLOWING:
MIL-F-14256F, Type R
NASA-STD-8739.3
DOD-STD-883E, Method 2022
ANSI/IPC J STD-004, Type ROL0
BELLCORE TR-NWT-000078
ANSI/IPC J SF-818
SODER-WICK SD BOBBINS ARE
DESIGNED TO MEET OR EXCEED:
MIL-STD-2000A
MIL-B-81705C
MIL-STD-1686C
MIL-HDBK-263B
TECHNICAL & APPLICATION
ASSISTANCE
Chemtronics provides a technical hotline to
answer your technical and application
related questions. The toll free number is:
1-800-TECH-401.
AVAILABILITY
40 Series Lead-Free No Clean Flux
25 bobbins / bag
five-foot bobbins in a vacuum
sealed can. This package
provides the highest level of
cleanliness and freshness. Great
for tool kit storage.
NOTE: This information is believed to be accurate. It
is intended for professional end users having the skills to
evaluate and use the data properly. CHEMTRONICS
does not guarantee the accuracy of the data and assumes
no liability in connection with damages incurred while
using it.
Chemtronics
8125 Cobb Center Drive
Kennesaw, GA 30152
1-770-424-4888
REV. A (02/05)
Chemtronics, Soder-Wick and CircuitWorks are
registered trademarks of Chemtronics. All rights reserved.
Vacu-Pak and ControlWipes are trademarks of
Chemtronics. All rights reserved.
DISTRIBUTED BY:
Loading...