Chemtronics QbE User Manual
CHEMTRONICS
TDS # QbE
Technical Data Sheet
®
QbE
PRODUCT DESCRIPTION
®
QbE
System for cleaning fiber optic end-faces.
It is a self-contained cleaning tool that can
be used “dry” or “wet.” The QbE
convenient and economical for use in field
or OEM applications.
TYPICAL APPLICATIONS
QbE
Telecommunications applications for:
• End-Face Connector Cleaning
• Splice Preparation
• Buffer Gel Removal
is the patented Precision Wipe
Th e Complete Fiber Optic Cleaning
System
Platen side of box provides surface
for cleaning
Effective “Wet” or “Dry” clea ning
Provides an ideal Cleaning System
for field or OEM applic ations
Convenient Size - Portable system
easily fits in tool cases and is handy
to use on work benches
Heavy Duty Lint-Free wiping
material tough-enough to remove
buffer-gel; soft enough for all end
face cleaning
Wipe material won’t shred or te ar
®
wipes are used in Fiber Optic and
Cleaning System
®
is
TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES
QbE® wipes are 100% noncontaminating
material. These wipes have high
absorbency and contamination entrapment
capacity, as well as high wet str ength.
Excellent solvent resistance
Excellent particle entra pment
High absorbency ca pacity and rate
Very low solvent e xtractables
High wet strength
COMPATIBILITY
®
QbE
wipes are compatible with most
common solvents such as alcohols,
hydrocarbons and chlorinated solvents.
The wipes are also generally compatible
with dilute or weak acids.
TECHNICAL AND APPLICATION
ASSISTANCE
ITW Chemtronics provides a technical
hotline to answer your te chnical and
application related questions.
The toll free
number is: 1-800-TECH-401.
Visit us at
www.combinationcleaning.com
, or
www.chemtronics.com
AVAILABILITY
®
QbE
Wipes 3" x 3" 200/Box
DISTRIBUTED BY:
USAGE INSTRUCTIONS
“Dry” Cleaning with the QbE®
1. Pull one QbE
foam platen.
2. Hold the end face at a 90 degree
perpendicular to the platen.
3. Draw the end face lightly over the platen in a
smooth linear motion - do not press too hard.
4. Do not retrace your cleaning procedure in the
same area.
5. Do not use a figure-eight motion; do not use
a “twist & turn” motion.
6. Check your work with a fiber scope or
measuring device.
“Wet” Cleaning with the QbE®
ith the QbE
1. Lightly “spot” the QbE
with Electro-Wash PX Fiber Optic Cleaner.
2. Draw the end-face from the solvent wetted
area to the dry area.
3. Check your work with a fiber scope or
measuring device.
For Splice Prep aration
1. Lightly moisten QbE
wipe away fiber contaminants.
2. Lightly dampen a 38540ESD swab,
remove soil from V-grooves on fusion
splicer.
Buffer Gel Removal
Buffer Gel Removal
1. Pull three single QbE
container.
2. Spray a small amount of Electro-Wash
PX Fiber Optic Cleaner into the folded
wipers.
3. Pull the cable through the first wiper and
discard.
4. Repeat until the cable “squeaks” clean.
®
Wipe over the fiber-safe
®
wipe on the platen
®
wipe and gently
®
Wipers out of the
CHEMTRONICS
8125 Cobb Center Drive
Kennesaw, GA 30152
1-770-424-4888 REV. C (08/13)
Chemtronics, Electro-Wash® and QbE® are
registered trademarks of Chemtronics. All rights
reserved.
CombinationCleaning is a trademark of
Chemtronics. All rights reserved
NOTE: This information is believed to be
accurate. It is intended for professional end users
having the skills to evaluate and use the data
properly. Chemtronics does not guarantee the
accuracy of the data and assumes no liability in
connection with damages incurred while using it.
Loading...