Chemtronics ES897B User Manual

Flux-Off® Lead-Free Flux-Off® LEAD FREE
1697
ES1697, ES897B
Other non-specified industry: Flux remover for No Clean soldering fluxes used in lead free soldering
Chemtronics 8125 Cobb Center Drive Kennesaw, GA 30152
Tel. 770-424-4888 or toll free 800-645-5244
Chemtrec - 1-800-424-9300 or collect 703-527-3887 24/7
Chemtronics 8125 Cobb Center Drive Kennesaw, GA 30152
Tel. 770-424-4888 or toll free 800-645-5244
12/20/2013.
Material Safety Data Sheet
Product name
Supplier
Trade name
Material uses
Manufacturer
Code
MSDS #
Validation date
Print date
In case of emergency
1. Product and company identification
Flux-Off® Lead-Free
:
:
:
:
:
:
:
:
:
:
Product type
:
Aerosol.
12/20/2013.
Signal word
2. Hazards identification
Potential acute health effects
Harmful by inhalation. At very high concentrations, can displace the normal air and cause suffocation from lack of oxygen.
Severely irritating to eyes. Risk of serious damage to eyes.
Harmful if swallowed. Irritating to mouth, throat and stomach.
Irritating to skin.
Eyes
Skin
Inhalation Ingestion
Physical state
Liquid. [Aerosol.]
DANGER!
EXTREMELY FLAMMABLE AEROSOL. CAUSES EYE AND SKIN IRRITATION. CONTAINS MATERIAL THAT MAY CAUSE TARGET ORGAN DAMAGE, BASED ON ANIMAL DATA.
:
:
:
:::
Odor
:
Hydrocarbon. [Slight]
OSHA/HCS status
:
This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Potential chronic health effects
Chronic effects
:
Contains material that may cause target organ damage, based on animal data.
Color
:
Colorless.
Emergency overview
Hazard statements
:
Precautionary measures
:
Do not breathe vapor or mist. Do not eat, drink or smoke when using this product. Avoid contact with eyes, skin and clothing. Keep away from heat, sparks, open flames and hot surfaces. - No smoking. Do not spray on an open flame or other ignition source. Pressurized container: Do not pierce or burn, even after use. Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F. Wash thoroughly after handling.
1/13
1697
12/20/2013.
Flux-Off® Lead-Free
2. Hazards identification
See toxicological information (Section 11)
Medical conditions aggravated by over­exposure
Pre-existing disorders involving any target organs mentioned in this MSDS as being at risk may be aggravated by over-exposure to this product.
:
Carcinogenicity
:
No known significant effects or critical hazards.
Mutagenicity
:
No known significant effects or critical hazards.
Teratogenicity
:
No known significant effects or critical hazards.
Developmental effects
:
No known significant effects or critical hazards.
Fertility effects
:
No known significant effects or critical hazards.
Over-exposure signs/symptoms
Ingestion
:
Adverse symptoms may include the following: nausea or vomiting
Skin
:
Adverse symptoms may include the following: irritation redness
Eyes
:
Adverse symptoms may include the following: pain or irritation watering redness
Inhalation
:
Adverse symptoms may include the following: respiratory tract irritation coughing dizziness/vertigo drowsiness/fatigue headache unconsciousness
Target organs
:
Contains material which causes damage to the following organs: the nervous system. Contains material which may cause damage to the following organs: blood, lungs, peripheral nervous system, gastrointestinal tract, cardiovascular system, upper respiratory tract, skin, central nervous system (CNS), eye, lens or cornea. acetone
67-64-1
20 - 50
hexane
107-83-5
10 - 25
3-methylpentane
96-14-0
1 - 20
2,3-dimethylbutane
79-29-8
1 - 20
2,2-dimethylbutane
75-83-2
1 - 20
Carbon dioxide
124-38-9
1 - 10
methanol
67-56-1
1 - 2
n-hexane
110-54-3
0.1 - 2
3. Composition/information on ingredients
Name
CAS number
%
There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health or the environment and hence require reporting in this section.
2/13
1697
12/20/2013.
Flux-Off® Lead-Free
Wash out mouth with water. Do not induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. Get medical attention immediately.
Check for and remove any contact lenses. Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Get medical attention immediately.
In case of contact, immediately flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash clothing before reuse. Clean shoes thoroughly before reuse. Get medical attention immediately.
Move exposed person to fresh air. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. Loosen tight clothing such as a collar, tie, belt or waistband. Get medical attention immediately.
4. First aid measures
Eye contact
Skin contact
Inhalation Ingestion
No specific treatment. Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.
Notes to physician
:
:
: : :
Protection of first-aiders
:
No action shall be taken involving any personal risk or without suitable training. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation.
Use an extinguishing agent suitable for the surrounding fire.
5. Fire-fighting measures
Extinguishing media
Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. Move containers from fire area if this can be done without risk. Use water spray to keep fire-exposed containers cool.
Extremely flammable aerosol. In a fire or if heated, a pressure increase will occur and the container may burst, with the risk of a subsequent explosion. Gas may accumulate in low or confined areas or travel a considerable distance to a source of ignition and flash back, causing fire or explosion. Bursting aerosol containers may be propelled from a fire at high speed. Runoff to sewer may create fire or explosion hazard.
Special protective equipment for fire-fighters
Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode.
:
Special exposure hazards
:
None known.
Suitable
:
Not suitable
:
Hazardous thermal decomposition products
:
Decomposition products may include the following materials: carbon dioxide carbon monoxide
Flammability of the product
:
No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. In the case of aerosols being ruptured, care should be taken due to the rapid escape of the pressurized contents and propellant. If a large number of containers are ruptured, treat as a bulk material spillage according to the instructions in the clean-up section. Do not touch or walk through spilled material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Avoid breathing vapor or mist. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment (see Section 8).
Environmental precautions
6. Accidental release measures
:
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air).
Personal precautions
:
Methods for cleaning up
3/13
1697
12/20/2013.
Flux-Off® Lead-Free
6. Accidental release measures
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and explosion-proof equipment. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations (see Section 13). Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Note: see Section 1 for emergency contact information and Section 13 for waste disposal.
Large spill
:
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and explosion-proof equipment. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Dispose of via a licensed waste disposal contractor.
Small spill
:
Store in accordance with local regulations. Store in a segregated and approved area. Store away from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Eliminate all ignition sources. Use appropriate containment to avoid environmental contamination.
Put on appropriate personal protective equipment (see Section 8). Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. Pressurized container: protect from sunlight and do not expose to temperatures exceeding 50°C. Do not pierce or burn, even after use. Do not ingest. Avoid contact with eyes, skin and clothing. Avoid breathing gas. Avoid breathing vapor or mist. Use only with adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Store and use away from heat, sparks, open flame or any other ignition source. Use explosion-proof electrical (ventilating, lighting and material handling) equipment. Use non-sparking tools. Empty containers retain product residue and can be hazardous.
7. Handling and storage
Handling
Storage
:
:
acetone
ACGIH TLV (United States, 3/2012).
STEL: 1782 mg/m³ 15 minutes. STEL: 750 ppm 15 minutes. TWA: 1188 mg/m³ 8 hours. TWA: 500 ppm 8 hours.
NIOSH REL (United States, 1/2013).
TWA: 590 mg/m³ 10 hours. TWA: 250 ppm 10 hours.
OSHA PEL (United States, 6/2010).
TWA: 2400 mg/m³ 8 hours. TWA: 1000 ppm 8 hours.
OSHA PEL 1989 (United States, 3/1989).
STEL: 2400 mg/m³ 15 minutes. STEL: 1000 ppm 15 minutes. TWA: 1800 mg/m³ 8 hours. TWA: 750 ppm 8 hours.
hexane
ACGIH TLV (United States, 3/2012).
TWA: 500 ppm 8 hours. TWA: 1760 mg/m³ 8 hours. STEL: 1000 ppm 15 minutes. STEL: 3500 mg/m³ 15 minutes.
8. Exposure controls/personal protection
Ingredient
Exposure limits
4/13
1697
12/20/2013.
Loading...
+ 9 hidden pages