Chemtronics ES830BE User Manual

Boiling Point

180°F Initial

Vapor Density (air=1)

>1

Solubility in Water

Soluble

Specific Gravity

0.79

Evaporation Rate >1

Appearance Clear, Colorless L iquid
Odor

Ethereal

Surface Tension

21.1

70°F

Shelflife Aerosols 5 years
Liquids 2 years after opening

CHEMTRONICS

Technical Data Sheet

Flux-Off  Water Soluble

TDS#830BE

PRODUCT DESCRIPTION

Flux-Off Water Soluble is a proprietary
blend of powerful cleaning solvents designed
to replace TMS based solvents. This
defluxing agent removes R, RMA, RA, and
synthetic flux residues, as well as ionic and
non-ionic soils.
 Removes R, RMA, RA, and synthetic flux

residues

 Penetrates hard to reach areas
 Evaporates quickly
 Leaves no residues
 Removes light oil and grea se residues
 Removes ionic and non-ionic r esidues
 Excellent material compatibility
 Non-corrosive formulation
 Contains no CFCs or HCFCs
 Contains no 1,1,1 Trichloroetha ne

TYPICAL APPLICATIONS



Flux-Off
residues and cleans:

 Chip Carriers
 Heat Sinks
 Plugs
 Printed Circuit Boards
 Relays
 Sockets
 Surface Mount Device Pads
 Switches

Water Soluble removes flux

TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES

(water = 1@77°F)

(butyl acetate=1)

(dynes/cm @21.6°C)
Flash Point (TCC)

Flammable
Kauri-Butanol (KB) Number 80

COMPATIBILITY



Flux-Off
compatible with most materials used in the
electronics industry. As with any cleaning
agent, solvent/component compatibility must
be determined on a non-critical area prior to
use.

Water Soluble is generally

Material

Compatibility

ABS

Good

Buna-N

Good

EPDM

Good

Graphite

Excellent

HDPE

Excellent

LDPE

Excellent

Lexan

Good

Neoprene

Good

Noryl

Excellent

Nylon 66

Excellent

Cross-Linked PE

Excellent

Polypropylene

Excellent

Polystyrene

Good

PVC

Excellent

Silicone Rubber

Good

Teflon

Excellent

Viton

Excellent

Performance

Product Required for Rosin Removal

1.23

CFC

0.0%

VOC

100%

HCFC

0.0%

HFC

0.0%

CL Solv.

0.0%

ODP

0.0

(mg solvent/ 1 mg rosin flux)

Flux-Off Water Soluble

Conventional TF Solvent Blends

Rosin Remval Rate (mg / in∧2 sec.)

Flux-Off Water Soluble

Conventional TF Solvent Blends

71.0

277.0

3.69

USAGE INSTRUCTIONS

For industrial use only.
Read MSDS carefully prior to use.
Spray 4-6” from surface to clean. Wash parts from
top to bottom, allowing the liquid to flush away dirt
and dissolved grease. For precise application use
attached extension tube. Product is Extremely
Flammable - Do not use near sources of ignition and
energized equipment.

AVAILABILITY

ES130E 3.7 L Liquid
ES830BE 6 oz. Brush Clean System - Europe

TECHNICAL & APPLICATION
ASSISTANCE

Chemtronics provides a technical hotline to answer
your technical and application related questions. The
toll free number is: 1-800-TECH-401.

ENVIRONMENTAL IMPACT DATA

ENVIRONMENTAL IMPACT DATA

CFC, HCFC, CL. SOLV., VOC, and HFC numbers shown
are the content by weight. Ozone depletion potential
(ODP) is determined in accordance with the Montreal
Protocol and U.S. Clean Air Act of 1990. The ODP of
this product is 0.0. It is the sum of the ODP of the
substances that may contribute to the depletion of
stratospheric ozone, based upon the weight of each
substance in the product’s formulation.

NOTE: This information is believed to be accurate. It is

intended for professional end users having the skills to
evaluate and use the data properly.
CHEMTRONICS does not guarantee the accuracy of the
data and assumes no liability in connection with damages
incurred while using it.

CHEMTRONICS
8125 COBB CENTER DRIVE
KENNESAW, GA 30152
1-770-424-4888

DISTRIBUTED BY:

REV. F (08/13)