Page 1
Vapor Density (air=1)
@ 100°F
Evaporation Rate <1
(Ether = 1)
<100 ppm
VOC* Content:
Federal 100 %
RoHS Compliant
Kauri-Butanol (KB) Number 80
CHEMTRONICS
Technical Data Sheet
IPA – Isopropyl Alcohol
TDS # 3205
PRODUCT DESCRIPTION
IPA – Isopropyl Alcohol is a highly effective,
general use cleaning solvent that is used to
clean a variety of substrates and remove a
variety of soils. This 99% pure IPA is
available in a variety of sizes for all types of
use.
TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES
Boiling Point
Melting Point
180°F
-128 °F
>1
Low surface tension
Effective cleaning agent
Solubility in Water
100%
Removes all types of residues, oxides, oils
and contaminants
Better than 99% pure
Specific Gravity
(water = 1)
0.79
Evaporates quickly and leaves no residue
Safe on most plastics and elastomers
Contains no CFCs, HCFCs or ODP’s
Appearance Clear, Colorless Liquid
ES105 = NSN 6810-00-286-5435
TYPICAL APPLICATIONS
IPA – Isopropyl Alcohol effectively removes
oils, dirt and dust from:
Commercial Tape, Record/Players
Industrial Tape, Record/Players
Compact disk laser readers
Electronic contacts
Tools
Electronic devices
Hard surfaces
Surface Tension
(dynes/cm @25°C)
Flash Point (TCC)
Non-Volatile Residue
CARB 100 %
SCAQMD 790 g/L
22
53°F
COMPATIBILITY
IPA – Isopropyl Alcohol is generally
compatible with most materials used in
electronics. As with any chemical product
used, component compatibility must be
determined on a non-critical area prior to use.
Do not use with energized equipment.
Shelflife 2 years after opening
*Volatile Organic Compound (VOC) information is calculated on a
weight basis using the VOC definition of California Air Resources
Board (CARB) Consumer Product Regulations, South Coast Air
Quality Management District (SCAQMD) Rule 102 and the Federal
definition published in 40 CFR 51.100(s).
Page 2
Material
Compatibility
Aluminum
Excellent
Buna-N
Good
CPVC
Excellent
Epoxy
Excellent
Neoprene
Good
Noryl
Excellent
Phenolic
Excellent
Cross-Linked PE
Good
Polycarbonate
Poor
Polypropylene
Good
Polystyrene
Poor
PVC
Fair
Teflon
Excellent
Tygon
Good
Viton
Excellent
CFC
0.0%
VOC
100%
HCFC
0.0%
HFC
0.0%
CL Solv.
0.0%
ODP
0.0
USAGE INSTRUCTIONS
For industrial use only.
Read MSDS carefully prior to use.
No special surface preparation is required prior
to applying IPA – Isopropyl Alcohol. For
optimum results, apply using Chamois Tips
to quickly and safely remove oxides, dust and
other contaminants. Use 6709 Econowipes™
for lint-free wiping of large areas.
AVAILABILITY
ES820L 8 fl. oz. Liquid
ES3205 32 fl. oz. Liquid
ES105 1 Gallon
ES505 5 Gallon
ES5505 55 Gallon
TECHNICAL & APPLICATION
ASSISTANCE
Chemtronics provides a technical hotline to answer
your technical and application related questions.
The toll free number is:
1-800-TECH-401.
ENVIRONMENTAL IMPACT DATA
ENVIRONMENTAL IMPACT DATA
CFC, HCFC, CL. SOLV., VOC, and HFC numbers shown are the
content by weight. Ozone depletion potential (ODP) is determined
in accordance with the Montreal Protocol and U.S. Clean Air Act of
1990. The ODP of this product is 0.0. It is the sum of the ODP of
the substances that may contribute to the depletion of stratospheric
ozone, based upon the weight of each substance in the product’s
formulation.
NOTE:
This information is believed to be accurate. It is
intended for professional end users having the
skills to evaluate and use the data properly.
CHEMTRONICS does not guarantee the accu racy
of the data and assumes no liability in connection
with damages incurred while using it.
Chemtronics is a registered trademark of Chemtronics. All
rights reserved. Chamois Tips and Econowipes are
trademarks of Chemtronics. All r igh ts re se r ved.
CHEMTRONICS
8125 COBB CENTER DRIVE
KENNESAW, GA 30152
1-770-424-4888 REV. D (08/13)
DISTRIBUTED BY:
Loading...