Chemtronics ES567 User Manual
Appearance
White, Opaque
Liquid
Specific Gravity
1.02
Appearance White, Opaque Liquid
Viscosity 18 cps @ RT
Flash Point (TCC)
None
Surface Resistivity
(ANSI/ESD S7.1)
106 – 109 ohms
Static Dec ay PASS
Coverage 1500 – 2000 sq ft. per gallon
any chemical product, component
CHEMTRONICS
Technical Data Sheet
Static Free Floor Finish
TDS # 0167
PRODUCT DESCRIPTION
Static Free Floor Finish is a high gloss floor
finish designed to dissipate electrostatic
charges and prevent static generation, while
providing protection and enhanced
appearance to a floor surface. It can be
applied to any hard floor surface, such as
vinyl, vinyl asbestos, rubber, linoleum and
other surfaces. Static Free
eliminates the need for static control tiles or
antistatic floor mats. Static Free™ Floor
Finish dries in 30 minutes and is perfect for
cleanroom, electronic manufacturing,
assembly and test areas.
Provides a non-yellow high gloss floor
surface
Dissipates static build up on floor s urfaces
Eliminates need for static control tiles
Dries in 30 minute s
Enhances the appearance of hard surfaces
Meets slip resistance standard ASTM D-
21.06
TYPICAL APPLICATIONS
Static Free
dissipates static electrical charges on floor
surfaces:
Vinyl Composition
Vinyl Asbestos
Rubber
Linoleum
Floor Finish effectively
Floor Finish
TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES
(water = 1)
(Brookfield DVII, No.1 spi ndle @
100RPM)
(MIL-B-81705C) (Less than 1 Second)
Shelf life 2 years
RoHS/WEEE
Status
COMPATIBILITY
Static Free Floor Finish is generally
compatible with most materials used in
commercial/industrial applications. As with
compatibility must be determined on a noncritical ar ea prior to use.
CFC
0.0%
VOC
9.0%
HCFC
0.0%
HFC
0.0%
CL Solv.
0.0%
ODP
0.0
USAGE INSTRUCTIONS
Make sure floor is stripped of previous floor
finish, and has been rinsed and cleaned. Pour
the Static Free™ Floor Finish into a clean
bucket. Immerse a rayon or other mop
designed for floor finish application into the
finish. Ring mop slightly, place on the floor
and apply in a figure eight motion. Repeat
until entire area has been coating. Allow
Static Floor Finish at least 30 minute drying
before adding additio nal coats.
AVAILABILITY
ES167 1 gallon con tainer
ES567 5 gallon con tainer
TECHNICAL & APPLICATION
ASSISTANCE
Chemtronics provides a technical hotline to
answer your technical and application related
questions. The toll free number is: 1-
800-TECH-401.
ENVIRONMENTAL IMPACT DATA
NOTE:
This information is believed to be accurate. It is
intended for professional end users having the skills
to evaluate and use the data properly.
CHEMTRONICS does not guar antee the accurac y of
the data and assumes no liability in connection with
damages incurred while using it.
Chemtronics® is registered tradema rks of Chemtronics. All rights reserved.
Static Free™ is a tradema r k o f C hemtronics. All rights reser ved.
All other trademarks herein are trademarks or registered trademarks of their
respecti ve o wners.
CHEMTRONICS
8125 COBB CENTER DRIVE
KENNESAW, GA 30152
1-770-424-4888
REV. C (08/13)
DISTRIBUTED BY:
ENVIRONMENTAL IMPACT DATA
CFC, HCFC, CL. SOLV., VOC, and HFC numbers
shown are the content by weight. Ozone depletion
potential (ODP) i s determ ined in acco rdance w ith the
Montreal Protocol and U.S. Clean Air Act of 1990.
The ODP of this product is 0.0. It is the sum of the
ODP of the substances that may contribute to the
depletion of stratospheric ozone, based upon the
weight of each substance in the product’s
formulation.
Loading...