Page 1
@ 77°F
@ 77°F /1 atm
Liquified Gas
CHEMTRONICS
Technical Data Sheet
Freez-It Antistat
TDS # 1051
PRODUCT DESCRIPTION
Freez-It Antistat is engineered for locating
thermal intermittent electrical components or
cooling printed circuit boards with minimal
static generation. This circuit refrigerant
system is nonflammable, residue-free and
provides fast cooling action.
Minimal static gener ation
Nonflammable
High heat transfer
Low static generation
Noncorrosive
Lowers tem perature to -60°F (51°C)
Ultra pure, filtered to <0.2 microns
Leaves no residue
Nonabrasive on most sur faces
Dries fast
Contains no CFCs or HCFCs
TYPICAL APPLICATIONS
Freez-It
Cool Equipment for Testing
Dissipate Heat W hile Soldering or
Isolate Therm al Intermittent
Test Circuit Trace s for Continuity
Test Printed Circuit Boar ds for Stress
Track Static Sensitive C omponents
Antistat can be used to:
Desoldering
Components
Fractures
TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES
Boiling Point -15.7°F
Vapor Density (air=1)
Solubility in Water
Specific Gravity
(water = 1 @77°F)
Evaporation Rate >1
(butyl acetate=1)
Appearance Clear, Colorless
Odor
Surface Tension
(dynes/cm @ 77°F)
Flash Point (TCC)
Shelflife 5 years
COMPATIBILITY
Freez-It
with most materials used in printed circuit
board fabrication, including sensitive
plastics and compounds. With any circuit
refrigerant, compatibility must be
determined on a non-critical area prior to
use.
Antistat is generally compatible
3.18
1.0% by weight
1.21
Slight Ethereal
7.8
None
Page 2
Material
Compatibility
Buna-N
Fair
Graphite
Good
HDPE
Good
LDPE
Good
Lexan
Poor
Neoprene
Good
Cross-Linked PE
Good
Polyacrylate
Poor
Polystyrene
Good
PVC
Good
Silicone Rubber
Fair
Teflon
Good
Viton
Poor
Freez-It Antistat
56% Less
40 v/in.
Static
Competitor’s
Antistat Freeze Spray
90 v/in.
0
20
40
60
80
100
120
Static Generation (V/IN.)
CFC
0.0%
VOC
0.9%
HCFC
0.0%
HFC
99.1%
CL Solv.
0.0%
ODP
0.0
Competitive Assessment of Freez-It Antistat
USAGE INSTRUCTIONS
For industrial use only.
Read MSDS carefully prior to use.
No special surface pre paration is required
prior to using Freez-It
Antistat. Direct spray
onto the area to instantly cool c omponents,
circuit boards or adhesives. For optimum
performance and pin point control, use
Freez-It
Antistat with the attached exte nsion
tube.
AVAILABILITY
ES1051 10 oz. Aerosol
ES1551 15 oz. Aerosol
TECHNICAL & APPLICATION
ASSISTANCE
Chemtronics provides a technical hotline to answer
your technical and application related questions.
The toll free number is:
1-800-TECH-401.
ENVIRONMENTAL IMPACT DATA
ENVIRONMENTAL IMPACT DATA
CFC, HCFC, CL. SOLV., VOC, and HFC numbers
shown are the content by weight. Ozone depletion
potential (ODP) is determined in accordance with the
Montreal Protocol and U.S. Clean Air Act of 1990. The
ODP of this product is 0.0. It is the sum of the ODP of
the substances that may contribute to the depletion of
stratospheric ozone, based upon the weight of each
substance in the product’s formulation.
NOTE:
This information is believed to be accurate . It is intended
for professional end users having the skills to evaluate
and use the data properly. CHEMTRONICS does not
guarantee the accuracy of the data and assumes no
liability in connection with damages incurred while using
it.
CHEMTRONICS
8125 COBB CENTER DRIVE
KENNESAW, GA 30152
1-770-424-4888
REV. E (08/13)
DISTRIBUTED BY:
Loading...