
Evaporation Rate
(butyl acetate=1)
Appearance Clear, Amber Liquid
Surface Tension
(dynes/cm @ 73°F)
RoHS Compliant
Shelflife 2 years after opening
Technical Data Sheet
PRODUCT DESCRIPTION
Flux-Off Aqueous is an extra-strength
water based cleaner for flux removal in
ultrasonic, batch and in-line cleaning
systems. It is an excellent cleaner for the
removal of all rosin and no clean flux types
from electronic subassemblies, printed
circuit boards and all other electronic
components. This concentrated formula can
be diluted 1:10 with deionized water for
handling all cleaning applications. Flux-Off
Aqueous will effectively remove other
contaminants such as dirt, grease, handling
soils and molding compounds.
For use with ultrasonic, batch and in-line
cleaning systems
Quickly removes all rosin and no clean
flux types
Re moves encrusted, har d, baked fluxes
Powerful cleaner leave s no residue
Conta ins no CFCs or HCFCs
Nonabrasive and noncorrosive
Nonflammable
RoHS compliant
TYPICAL APPLICATIONS
Flux-Off
and cleans:
Chip Carriers
H eat Sinks
Me tal Housings and Chassis
Motor s and Generators
Printed Circuit Boards
Surface Mount Device Pads
Aqueous removes flux residues
TDS # 132
Flux-Off Aqueous
TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES
CARB and Federal rule 16 %
SCAQMD Rule 1122 165 g/L concentrate
*Volatile Organic Compound (VOC) information is calculated on a
weight basis using the VOC definition of California Air Resources
Board (CARB) Consumer Product Regulations, South Coast Air
Quality Management District (SCAQMD) Rule 102 and the Federal
definition published in 40 CFR 51.100(s).
COMPATIBILITY
Flux-Off
with most materials used in printed circuit
board fabrication. With any cleaning agent
compatibility must be determined on a noncritical area prior to use.
Aqueous is generally compatible

USAGE INSTRUCTIONS:
For industrial use only.
Read MSDS care fully prior to use.
Dilute 1:10 with deionized wate r for general
cleaning. Can be used in hot or cold
immersion, ultrasonic or aqueous cleaning
systems. For imme rsion systems, soa k as
necessary. For ultrasonic cleaning, add
Flux-Off
Aqueous to the ultrasonic
cleaning tank, allow about two minutes for
the mixture to degas, and immer se the part to
be cleaned in the ultrasonic clea ner. After
cleaning, rinse parts thoroughly in deionized water and dry where required.
AVAILABILITY
ES132 1 Gallon Liquid
ENVIRONMENTAL IMPACT DATA
Hydrochlorofluorocarbons (HCFCs) are regulated un der the Mont real Protocol
as Class II ozone depleting substances. HCFC-141b is no longer produced in
the US under this legislation. HCFC-225 is planned for production phase-out
in 2015. Hydrofluorocarb ons (HFCs) are not currently regulated.
EPA has listed n-propyl bromide (nPB) as an acceptable alternative to ozone
depleting substances in metal, precision, and electronics cleaning under
Section 612 of the Clean Air Act.
TECHNICAL & APPLICATION
ASSISTANCE
Chemtronics provides a technical hotline to
answer your tec hnical and application related
questions. The toll free number is: 1-800-
TECH-401.
NOTE:
This information is believed to be accurate. It is
intended for professional end users having the skills
to evaluate and use the data properly.
CHEMTRONICS does no t guarantee t he accuracy of
the data and assumes no liability in connection with
damages incurred while using it.
Chemtronics and F lux-Off are registered trademarks of
Chemtronics. All rights reserved.
All other trademarks herein are trademarks or registered
trademarks of their respective owners.
CHEMTRONICS
8125 COBB CENTER DRIVE
KENNESAW, GA 30152
1-770-424-4888
REV. F (08/13)
DISTRIBUTED BY: