Chemtronics ES1056 User Manual

Page 1
@ 70°F
@ 70°F /1 atm
Liquified Gas
Internal Pressure
5 years
RoHS/WEEE
TDS # 1056
CHEMTRONICS
Technical Data Sheet
Arctic Storm™ Freeze Spray
PRODUCT DESCRIPTION
Arctic Storm™ Freeze Spray is specifically designed for cooling large areas of a printed circuit board at once to locate thermally intermittent sections. Utilizing an ultra-low global warming potential coolant, this product offers the best cooling possible with the lowest global warming impact available. Arctic Storm™ Freeze Spray is nonflammable, residue-free and provides very fast cooling action.
Cools surfaces to below -49°F / -45 °C Wide spray for whole board cooling Ultra-low global warming impact of 6 NonflammableHigh heat transferNoncorrosive Ultra-pure, filtered to <0.2 microns Leaves no residue Nonabrasive on most surfaces CFC, HCFC and HFC free VOC free
TYPICAL APPLICATIONS Arctic Storm™ Freeze Spray can be used to:
Cool Equipment for Testing Dissipate Heat While Soldering or
Desoldering
Isolate Thermal Intermittent Components Test Circuit Traces for Continuity Test Printed Circuit Boards for Stress
Fractures
Track Intermittent Failures and Shorts
COMPATIBILITY Arctic Storm™ Freeze Spray is generally compatible with most materials used in printed circuit board fabrication, including sensitive plastics and compounds. With any circuit refrigerant, compatibility must be determined on a non-critical area prior to use.
TYPICAL PRODUCT DATA AND PHYSICAL PROPERTIES
Boiling Point -2 °F / -19 °C
Cools To:
Vapor Density (air=1)
Solubility in Water
Specific Gravity (water = 1 @70°F)
Evaporation Rate >1 (butyl acetate=1)
Appearance Clear, Colorless
Odor
Flash Point (TCC)
Shelflife
Status
-49 °F / -45 °C
4.0
>0.10% by weight
1.17
Slight Ethereal
47 psia @ 70 °F
None
Page 2
Material
Compatibility
Buna-N
Good
Graphite
Excellent
HDPE
Fair
LDPE
Fair
Lexan
Good
Neoprene
Good
Cross-Linked PE
Good
Polyacrylate
Good
Polystyrene
Good
PVC
Good
Silicone Rubber
Fair
Teflon
Fair
Viton
Poor
CFC
0.0%
VOC
0.0%
HCFC
0.0%
HFC
0.0%
CL Solv.
0.0%
ODP
0.0
to evaluate and use the data properly.
TECHNICAL & APPLICATION ASSISTANCE
Chemtronics provides a technical hotline to answer your technical and application related questions. The toll free number is:
1-800-TECH-401.
ENVIRONMENTAL IMPACT DATA
ENVIRONMENTAL IMPACT DATA
USAGE INSTRUCTIONS For industrial use only. Read MSDS carefully prior to use. No special surface preparation is required prior to using Arctic Storm™ Freez e S pray. Direct spray onto the area to instantly cool components, circuit boards or adhesives. For optimum performance and pin point control, use Arctic Storm™ Freeze Spray with the attached extension tube.
AVAILABILITY ES1056 10 oz. Aerosol
DISTRIBUTED BY:
CFC, HCFC, CL. SOLV., VOC, and HFC numbers shown are the content by weight. Ozone depletion potential (ODP ) is determined in acco rdance with the Montreal Protocol and U.S. Clean Air Act of 1990. The ODP of this product is 0.0. It is the sum of the ODP of the substances that may contribute to the depletion of stratospheric ozone, based upon the weight of each substance in the product’s formulation. VOC consideration is based on the materials being not photochemically reactive by Commonly Used Standards (material supplier).
NOTE:
This information is believed to be accurate. It is intended for professional end users having the skills
CHEMTRONICS do es not guarantee the accuracy of the data and assumes no liability in connection with damages incurred while using it.
Chemtronics® is a registered trademark of Chemtronics. All rights reserve d. Arctic Storm™ is a trademark of Chemtronics. All rights reserved. All other trademarks herein are trademarks or registered trademarks of their respective owners.
CHEMTRONICS 8125 COBB CENTER DRIVE KENNESAW, GA 30152 1-770-424-4888 REV. B (08/13)
Loading...