Page 1
@ 77°F
@ 77°F F/1 atm
Air, % by Volu me
UEL : 16.9
5 years
CHEMTRONICS
Technical Data Sheet
TDS # 1029
152a Blast™
PRODUCT DESCRIPTION
152a Blast™ is an economical generalpurpose duster with a bigger blast for
cleaning applications. Its exceptional purity
jet instantly cleans surfaces free of particulate
contamination. 152a Blast™ is engineered to
remove dirt, dust, oxide particles and other
airborne particles instantly, and can be used
to facilitate the accelerated drying of solvent
cleaners. Not for use near flames, ignition
sources, nor sources of static discharge.
High pressure for contamination control
Ozone safe; CFC and HCFC free
Flammable
63 psig at 70
Nonabrasive; safe for most materials.
Will not scratch surfac es
No residue
Cleans hard to reach areas
TYPICAL APPLICATIONS
152a Blast™ is used in a wide range of
applications including:
Audio/Video Equipment
Fax Machines
Keyboards
Laboratory I nstruments
Microcomputers
Photo Equipment
Printers
o
F
TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES
Boiling Point -15.0°F
Vapor Density (air=1)
Solubility in Water
Specific Gravity
(water = 1 @77°F)
Evaporation Rate >1
(butyl acetate=1)
Appearance Clear, Colorless Gas
Odor
Flammable limits in
Flash Point (TCC)
Shelflife
COMPATIBILITY
152a Blast™ is generally compatible with
most materials used in printed circuit board
fabrication, including sensitive plastics and
compounds. As with any duster,
compatibility must be determined on a noncritical area prior to use.
2.4
0.15% by weight
1.22
Slight Ethereal
LEL : 3.9
<-50 C (<-58 F)
Page 2
Material
Compatibility
Buna-N
Excellent
Graphite
Excellent
HDPE
Excellent
LDPE
Excellent
Lexan
Excellent
Neoprene
Excellent
Cross-Linked PE
Excellent
Polyacrylate
Excellent
Polystyrene
Excellent
PVC
Excellent
Silicone Rubber
Excellent
Teflon
Excellent
Viton
Excellent
PERFORMANCE
Pressure PSI G / Temperature F
200 - P 150 - S I 100 - G 50 - 0
70
80
90
100
110
120
130
Temperature F
CFC
0.0%
VOC
0.0%
HCFC
0.0%
HFC
100.0%
GWP
140
ODP
0.0
USAGE INSTRUCTIONS
For industrial use only.
Read MSDS carefully prior to use.
No special surface preparation is required prior to
using 152a Blast™. Direct high pressure spray onto
the area to be cleaned to remove dust, dirt and other
contaminant. For optimum performance and pin point
control, use with the attached extension tube. Do not
use near ignition sources or energized equipment.
Do not spray into enclosed areas where flammable
vapors may accumulate.
TECHNICAL & APPLICATION
ASSISTANCE
Chemtronics provides a technical hotline to answer
your technical and application related qu estions. The
toll free number is 1-800-TECH-401, or e-mail us at
AskChemtronics@chemtronics.com .
Chemtronics is also accessible on the web. Visit us at
www.chemtronics.com.
AVAILABILITY
ES1029 10 oz. Aerosol
ENVIRONMENTAL IMPACT DATA
ENVIRONMENTAL IMPACT DATA
CFC, HCFC, VOC, a nd HFC numbers sho wn are the content by
weight. Ozone depletion potential (ODP) is determined in
accordance with the Montreal Protocol and U.S. Clean Air Act
of 1990. The ODP of this product is 0.0. It is the sum of the
ODP of the substances that may contribute to the depletion of
stratospheric ozone, based upon the weight of each substance in
the product’s formulation.
calculated based on a 100 year time horizon. Carbon dioxide has
a GWP of 1.
Global warming potential (GWP) is
NOTE:
This information is believed to be accurate . It is intended
for professional end users having the skills to evaluate and
use the data properly. CHEMTRONICS does not
guarantee the accuracy of the data and assumes no liability
in connection with damages incurred while using it.
Chemtronics is a registered trad emark of Chemtronics . All rights r eserved.
152a Blast is a trademark of Chemtronics. All rights reserved. All other
trademarks herein are trademarks or registered trademarks of their respective
owners.
CHEMTRONICS
8125 COBB CENTER DRIVE
KENNESAW, GA 30152
1-770-424-4888
REV. A 08/13
DISTRIBUTED BY:
Loading...