Chemtronics ES1020 User Manual

Page 1
@ 77°F
@ 77°F F/1 atm
Liquified Gas
5 years
CHEMTRONICS
Technical Data Sheet
TDS # 1020
PRODUCT DESCRIPTION
Ultrajet compressed gas duster is a high pressure duster that cleans electronics without scratching delicate surfaces. This duster/ cleaner is nonflammable, residue-free and won’t scratch delicate surfaces.
Filtered to 0.2 microns Nonflammable Leaves no residueHigh pressure for contamination control NonabrasiveExcellent mate rial compatibility Penetrates hard to reach areasContains no ozone depleting com pounds
TYPICAL APPLICATIONS
Ultrajet of electronic equipm ent maintenance and is particularly suited for applications involving:
Audio/Video Equipm ent Computers and Othe r Electronic
Fax MachinesLaboratory Instr uments Photo EquipmentPrinted Circuit BoardsPrintersSurface Mount Device s
duster is engineered for all aspects
Equipment
Ultrajet
TYPICAL PRODUCT DATA AND PHYSICAL PROPERTIES
Boiling Point -15.7°F
Vapor Density (air=1)
Solubility in Water
Specific Gravity (water = 1 @77°F)
Evaporation Rate >1 (butyl acetate=1)
Appearance Clear, Colorless
Odor Surface Tension
(dynes/cm @77°F) Flash Point (TCC)
Shelflife
COMPATIBILITY
Ultrajet materials used in printed circuit board fabrication, including sensitive plastics and compounds. As with any duster/cleaner, compatibility must be determined on a non­critical area prior to use.
3.18
0.10% by weight
1.21
Slight Ethereal
7.8
None
is generally compatible with most
Page 2
Material
Compatibility
Buna-N
Excellent
Graphite
Excellent
HDPE
Excellent
LDPE
Excellent
Lexan
Excellent
Neoprene
Excellent
Cross-Linked PE
Excellent
Polyacrylate
Excellent
Polystyrene
Excellent
PVC
Excellent
Silicone Rubber
Excellent
Teflon
Excellent
Viton
Excellent
PERFORMANCE
Pressure PSI G / Temperature F
200 - P 150 S - I 100 G - 50 - 0
20
40
60
80
100
120
140
Temperature F
CFC
0.0%
VOC
0.0%
HCFC
0.0%
HFC
100.0%
CL Solv.
0.0%
ODP
0.00
TECHNICAL & APPLICATION ASSISTANCE
Chemtronics provides a technical hotline to answer your technical and application related questions. The toll free number is:
1-800-TECH-401
.
ENVIRONMENTAL IMPACT DATA
ENVIRONMENTAL IMPACT DATA
USAGE INSTRUCTIONS For industrial use only. Read MSDS care fully prior to use. No special surface preparation is required
prior to using Ultrajet
. Direct high pressure spray onto the area to be cleaned to remove dust, dirt and other contaminant. For optimum performance and pin point c ontrol, use with the attached extension tube.
AVAILABILITY
ES1020 10 oz. Aerosol ES520 5 oz. Aerosol
CFC, HCFC, CL. SOLV., VOC, and HFC numbers shown are the content by weight. Ozone depletion potential (ODP) is determined in accordance with the Montreal Protocol and U.S. Clean Air Act of 1990. The ODP of this product is 0.0. It is the sum of the ODP of the substances that may contribute to the depletion of stratospheric ozone, based upon the weight of each substance in the product’s formulation.
NOTE:
This information is believed to be accurate. It is intended for professional end users having the skills to evaluate and use the data properly. CHEMTRONICS does not guarantee the accuracy of the data and assumes no liability in connection with damages incurred while using it.
CHEMTRONICS 8125 COBB CENTER DRIVE KENNESAW, GA 30152 1-770-424-4888 REV. E (08/13)
DISTRIBUTED BY:
Loading...