Water Soluble Flux Pen – CW8300
Flux Type Water Soluble
ORH1
Flash Point (TCC) 60oF (16oC)
pH 6.0 – 7.0
Appearance Yellow Liquid
Odor Slight
Shelf life
RoHS Compliant
CHEMTRONICS
TDS #CW 8300
Technical Data Sheet
CircuitWorks
PRODUCT DESCRIPTION
CircuitWorks Water S oluble F lux P en is
designed spe cifically to apply water soluble
flux with pr ecision c ontrol. The W ater
Soluble Flux consists of a neutral pH organic
water soluble flux compatible with most
solder m asks. T he high a ctivity or ganic
product c leans e asily w ith water, reducing
cleaning cost.
pH neutral
Completely portable package
Cleans with water
Excellent material compatibility
Good soldering properties
ORH1 Classification
TYPICAL APPLICATIONS
CircuitWorks
Flux Dispensing Pens
precisely dispense flux on:
Printed Circuit Boards
Chip Carriers
Heat Sinks
Surface Mount Device Pads
Switches
Sockets
Water Soluble Flux Pen
TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES
2 years
RELIABILITY PROPERTIES
Copper Mirror Corrosion: High
Tested to J-STD-004, IPC TM-650, Method 2.3.32
Corrosion Test: High
Tested to J-STD-004, IPC-TM-650, Method 2.6.15
Silver Chromate: Fail
Tested to J-STD-004, IPC-TM-650, Method 2.3.33
Chloride and Bromides: 2.2%
Tested to J-STD-004, IPC-TM-650, Method 2.3.35
Fluorides by Spot Test: Pass
Tested to J-STD-004, IPC-TM-650, Method 2.3.35.1
SIR, IPC (typical): Pass
Tested to J-STD-004, IPC-TM-650, Method 2.6.3.3
COMPATIBILITY
ODP
None
VOC
Yes
HCFC
None
HFC
None
CircuitWorks
Water S oluble F lux P en is
generally compatible w ith m ost m aterials
used in the electronics industry. As with any
cleaning agent, material compatibility should
be de termined on a non -critical a rea pr ior to
use.
USAGE INSTRUCTIONS
For industrial use only.
Read MSDS carefully prior to use.
Flux Application: Water Soluble Flux should
only be applied to a reas to be soldered. Hold
pen vertically, touch surface of PCB and
briefly de press tip to sta rt liquid f low.
Lightly w ipe pen tip o ver surface to be
fluxed. Use a C ontrolWipe dry w ipe to
remove flux buildup.
Cleaning: Flux residues m ust be r emoved
after soldering as they a re conductive and
corrosive. No neutralizer, sa ponifiers or
detergent are necessary for complete removal
of flux residues. It is not recommended to use
high m ineral c ontent ta p w ater, therefore
deionized or softened water may be used for
cleaning. The optim um w ater te mperature is
o
54-66
Off
C (1 30-150oF). Chemtronics Flux-
Water Soluble may also be used as a flux
remover.
TECHNICAL & APPLICATION
ASSISTANCE
Chemtronics provides a technical hotline to
answer your te chnical and application related
questions. The toll f ree num ber is: 1-800-
TECH-401.
AVAILABILITY
CW8300 9 gm (0.32 oz) Flux Pen
ENVIRONMENTAL IMPACT DATA
Ozone depletion potential (ODP) is determined in accordance with the Montreal
Protocol and U.S. Clean Air Act of 1990. H ydrochlorofluorocarbons (HCFCs)
are regulated under the Montreal Protocol as Class II ozone depleting substances.
Volatile Organic Compound (VOC) information is calculated on a weight basis
using the VOC definition of California Air Resources Board (CARB) Consumer
Product Regulations, South Coast Air Quality Management District (SCAQMD)
Rule 1 02 a nd t he F ederal definition p ublished i n 4 0 C FR 5 1.100(s).
Hydrofluorocarbons (HFCs) are not currently regulated.
NOTE: This inf ormation is be lieved to be
accurate. It is intended f or pr ofessional e nd
users having the skills to evaluate and use the
data properly.
CHEMTRONICS does not gua rantee the
accuracy of the data and a ssumes no liability
in c onnection w ith da mages inc urred w hile
using it.
Chemtronics, Flux-Off and C ircuitWorks are r egistered
trademarks of Chemtronics. All rights reserved. ControlWipe
is a trademark of Chemtronics. All rights reserved.
DISTRIBUTED BY:
Loading...