Page 1
Water Soluble Flux Pen – CW8300
Flux Type Water Soluble
ORH1
Flash Point (TCC) 60oF (16oC)
pH 6.0 – 7.0
Appearance Yellow Liquid
Odor Slight
Shelf life
RoHS Compliant
CHEMTRONICS
TDS #CW 8300
Technical Data Sheet
CircuitWorks
PRODUCT DESCRIPTION
CircuitWorks Water Soluble Flux Pen is
designed specifically to apply water soluble
flux with precision control. The Water
Soluble Flux consists of a neutral pH organic
water soluble flux compatible with most
solder masks. The high activity organic
product cleans easily with water, reducing
cleaning cost.
pH neutral
Completely portable package
Cleans with water
Excellent mate rial compatibility
Good soldering properties
ORH1 Classification
TYPICAL APPLICATIONS
CircuitWorks
Flux Dispensing Pens
precisely dispense flux on:
Printed Circuit Boards
Chip Carriers
Heat Sinks
Surface Mount Device Pads
Switches
Sockets
Water Soluble Flux Pen
TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES
2 years
RELIABILITY PROPERTIES
Copper Mirror Corrosion: High
Tested to J-STD-004, IPC TM-650, Method 2.3.32
Corrosion Test: High
Tested to J-STD-004, IPC-TM-650, Method 2.6.15
Silver Chromate: Fail
Tested to J-STD-004, IPC-TM-650, Method 2.3.33
Chloride and Bromides: 2.2%
Tested to J-STD-004, IPC-TM-650, Method 2.3.35
Fluorides by Spot Test: Pass
Tested to J-STD-004, IPC-TM-650, Method 2.3.35.1
SIR, IPC (typical): Pass
Tested to J-STD-004, IPC-TM-650, Method 2.6.3.3
Page 2
COMPATIBILITY
ODP
None
VOC
Yes
HCFC
None
HFC
None
CircuitWorks
Water Soluble Flux Pen is
generally compatible with most materials
used in the electronics industry. As with any
cleaning agent, material compatibility should
be determined on a non-critical area prior to
use.
USAGE INSTRUCTIONS
For industrial use only.
Read MSDS care fully prior to use.
Flux Application: Water Soluble Flux should
only be applied to areas to be soldered. Hold
pen vertically, touch surface of PCB and
briefly depress tip to start liquid flow.
Lightly wipe pen tip over surface to be
fluxed. Use a ControlWipe dry wipe to
remove flux buildup.
Cleaning: Flux residues must be removed
after soldering as they are conductive and
corrosive. No neutralizer, saponifiers or
detergent are necessary for complete removal
of flux residues. It is not recommended to use
high mineral content tap water, therefore
deionized or softened water may be used for
cleaning. The optimum water temperature is
o
54-66
Off
C (130-150oF). Chemtronics Flux-
Water Soluble may also be used as a flux
remover.
TECHNICAL & APPLICATION
ASSISTANCE
Chemtronics provides a technical hotline to
answer your technical and application related
questions. The toll free number is: 1-800-
TECH-401.
AVAILABILITY
CW8300 9 gm (0.32 oz) Flux Pen
ENVIRONMENTAL IMPACT DATA
Ozone depletion potential (ODP) is determined in accordance with the Montreal
Protocol and U.S. Clean Air Act of 1990. Hydrochlorofluorocarbons (HCFCs)
are regulated under the Montreal Protocol as Class II ozone depleting substances.
Volatile Organic Compound (VOC) information is calculated on a weight basis
using the VOC definition of California Air Resources Board (CARB) Consumer
Product Regulations, South Coast Air Quality Management District (SCAQMD)
Rule 102 and the Federal definition published in 40 CFR 51.100(s).
Hydrofluorocarbons (HFCs) are not curren tly regulated.
NOTE: This information is believed to be
accurate. It is intended for professional end
users having the skills to evaluate and use the
data properly.
CHEMTRONICS does not guarantee the
accuracy of the data and assumes no liability
in connection with damages incurred while
using it.
CHEMTRONICS
8125 COBB CENTER DRIVE
KENNESAW, GA 30152
1-770-424-4888
Chemtronics, Flux-Off and CircuitWorks are registered
trademarks of Chemtronics. All rights reserved. ControlWipe
is a trademark of Chemtronics. All rights reserved.
Rev. B (08/13)
DISTRIBUTED BY:
Loading...