Page 1
Silicone Grease
Color Silver/Gray
Consistency Smooth Paste
Volume resistivity <0.01 ohm-cm
( W/m°K) 5.6
Range (-57 to 252°C)
(ASTM D-1403) 77°F
(ASTM D-1403, 60 Strokes)
(ASTM D-2266)
(ASTM D-2266)
Corrosion on Copper None
Moisture Resistance Excellent
Chemical Resistance Excellent
Electrical Conductivity Excellent
Thermal Conductivity Excellent
Lubrication Properties Excellent
Protection from Oxidation Excellent
Power Rating High/Low
Shelf life 2 years
RoHS Compliant
CHEMTRONICS
Technical Data Sheet
CircuitWorks Silver Conductive Grea se
TDS # CW7100
PRODUCT DESCRIPTION
CircuitWorks
Silver Conductive Grease
provides maximum electrical and thermal
conductivity, proven lubrication properties,
and protection from moisture, oxidation,
and other environmental hazards. This
system utilizes an advanced silicone
lubricant that is compatible with metal,
rubber, and plastic.
High electrical conductivity
Excellent therm al conductivity
Provides protection against wea r
Remains stable in a wide temperature
range; -70 to 485°F (-57 to 252°C)
Protects against moistur e and corrosion
Very low viscosity vs. tempe rature
change
TYPICAL APPLICATIONS
CircuitWorks
Silver Conductive Grease
may be used for high and low power
applications including:
Lubrication of Substation Switches or
Circuit Breakers
Heat Dissipation from Transformers
Low or Medium Speed Sliding
Contacts
Static Grounding on Seals or O-Rings
Extending the Life of Rotating
Switches
TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES
Composition
Material 100% Silver Filled
Properties
Thermal Conductivity
(BTU-in/hr-ft2 -°F) 38.8
(CAL-cm/sec-cm2 -°C) 1.3 x 10-2
Operating Temperature -70 to 485°F
Unworked Penetration 210
Worked Penetration 250
Dropping Point 491°F (255°C)
Steel on Steel Wear 1.5mm
Page 2
COMPATIBILITY
CircuitWorks
Silver Conductive Grease is
generally compatible with metal, rubber,
and plastic. As with any compound,
compatibility with substrate should be
determined on a non-critical area prior to
use.
USAGE INSTRUCTIONS
Surface Preparation: For best results,
clean parts to be lubricated with
Chemtronics
Electro-Wash PX clean er in
order to remove any surface contamination
which may prevent adequate material
contact.
Thinning: Do not attempt to thin.
Application:
Syringe: Remove cap and gently press on
plunger. Apply CircuitWorks Silver
Conductive Grease directly to surface or use
application tip.
Clean-Up: Electro-Wash
PX cleaner can
be used to remove trace residues. Excess
material may also be removed using a wipe
such as the Chemtronics
Silver particles may stain porous materials.
ControlWipes.
WARNING:
To avoid shock or possible fire, stop power to
any system before applying conductive grease.
Insure positive and negative contacts remain
isolated. Improper use can result in shorting,
arcing, or shock.
AVAILABILITY
CW7100 6.5g / 0.23 oz. Syringe
TECHNICAL & APPLICATION
ASSISTANCE
Chemtronics provides a technical hotline to answer
your technical and application related questions.
The toll free number is: 1-800-TECH-401.
NOTE:
This information is believed to be accurate. It is
intended for professional end users having the skills
to evaluate and use the data properly.
CHEMTRONICS does not guarantee the accuracy
of the data and assumes no liability in connection
with damages incurred while using it.
Chemtronics, Electro-Wash and CircuitWorks are
registered trademarks of Chemtronics. All rights reserved.
ControlWipes is a trademark of Chemtronics. All rights
reserved.
CHEMTRONICS
8125 COBB CENTER DRIVE
KENNESAW, GA 30152
1-770-424-4888
DISTRIBUTED BY:
REV. H (08/13)
Loading...