Page 1
Konform® SR (liquid)
Konform® SR (Liquid) (Formerly Konform® SR 2000)
Konform® SR - CTSR1, CTSR5, CTSR55, CTSR1C, CTSR5C, CTSR55C
0710L
CTSR1 CTSR5, CTSR55, CTSR1C, CTSR5C, CTSR55C
Coating Solution
Chemtronics
8125 Cobb Center Drive
Kennesaw, GA 30152
Tel. 770-424-4888 or toll free 800-645-5244
Chemtrec - 1-800-424-9300 or collect 703-527-3887
24/7
Chemtronics
8125 Cobb Center Drive
Kennesaw, GA 30152
Tel. 770-424-4888 or toll free 800-645-5244
9/5/2014.
Material Safety Data Sheet
Product name
Supplier
Synonym
Trade name
Material uses
Manufacturer
Code
MSDS #
Validation date
Print date
In case of emergency
1. Product and company identification
Konform® SR (liquid)
:
:
:
:::::
:
::Product type
:
liquid
9/5/2014.
Signal word
2. Hazards identification
Potential acute health effects
Harmful by inhalation. At very high concentrations, can displace the normal air and
cause suffocation from lack of oxygen.
Severely irritating to eyes. Risk of serious damage to eyes.
Harmful if swallowed. Irritating to mouth, throat and stomach.
Irritating to skin.
Eyes
Skin
Inhalation
Ingestion
Physical state
Liquid.
WARNING!
FLAMMABLE LIQUID AND VAPOR. CAUSES EYE AND SKIN IRRITATION. MAY BE
HARMFUL IF SWALLOWED. CONTAINS MATERIAL THAT MAY CAUSE TARGET
ORGAN DAMAGE, BASED ON ANIMAL DATA.
:
:
:
:
:
:
Odor
:
Hydrocarbon.
OSHA/HCS status
:
This material is considered hazardous by the OSHA Hazard Communication Standard
(29 CFR 1910.1200).
Potential chronic health effects
Carcinogenicity
:
No known significant effects or critical hazards.
Mutagenicity
:
No known significant effects or critical hazards.
Chronic effects
:
Contains material that may cause target organ damage, based on animal data.
Color
:
Translucent. Light Green.
Emergency overview
Hazard statements
:
Precautionary measures
:
Do not breathe vapor or mist. Do not ingest. Use only with adequate ventilation. Do
not eat, drink or smoke when using this product. Avoid contact with eyes, skin and
clothing. Keep away from heat, sparks and flame. Keep container tightly closed. Wash
thoroughly after handling.
1/13
0710L
9/5/2014.
Page 2
Konform® SR (liquid)
2. Hazards identification
See toxicological information (Section 11)
Medical conditions
aggravated by overexposure
Pre-existing disorders involving any target organs mentioned in this MSDS as being at
risk may be aggravated by over-exposure to this product.
:
Teratogenicity
:
No known significant effects or critical hazards.
Developmental effects
:
No known significant effects or critical hazards.
Fertility effects
:
No known significant effects or critical hazards.
Over-exposure signs/symptoms
Ingestion
:
Adverse symptoms may include the following:
Irritating to mouth, throat and stomach.
Skin
:
Adverse symptoms may include the following:
irritation
redness
Eyes
:
Adverse symptoms may include the following:
pain or irritation
watering
redness
Inhalation
:
Adverse symptoms may include the following:
dizziness/vertigo
drowsiness/fatigue
headache
unconsciousness
Target organs
:
Contains material which may cause damage to the following organs: blood, kidneys, the
nervous system, the reproductive system, liver, peripheral nervous system, upper
respiratory tract, skin, central nervous system (CNS), eye, lens or cornea.
hexane
107-83-5
20 - 40
toluene
108-88-3
10 - 15
2,2-dimethylbutane
75-83-2
10 - 15
2,3-dimethylbutane
79-29-8
10 - 15
3-methylpentane
96-14-0
10 - 15
acetone
67-64-1
5 - 10
2-methoxy-1-methylethyl acetate
108-65-6
3 - 8
n-hexane
110-54-3
1 - 2
3. Composition/information on ingredients
Name
CAS number
%
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require reporting
in this section.
Check for and remove any contact lenses. Immediately flush eyes with plenty of water
for at least 15 minutes, occasionally lifting the upper and lower eyelids. Get medical
attention immediately.
In case of contact, immediately flush skin with plenty of water for at least 15 minutes
while removing contaminated clothing and shoes. Wash clothing before reuse. Clean
shoes thoroughly before reuse. Get medical attention immediately.
Move exposed person to fresh air. If not breathing, if breathing is irregular or if
respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel.
Loosen tight clothing such as a collar, tie, belt or waistband. Get medical attention
immediately.
4. First aid measures
Eye contact
Skin contact
Inhalation
:
:
:
2/13
0710L
9/5/2014.
Page 3
Konform® SR (liquid)
4. First aid measures
Wash out mouth with water. Do not induce vomiting unless directed to do so by medical
personnel. Never give anything by mouth to an unconscious person. Get medical
attention immediately.
Ingestion
No specific treatment. Treat symptomatically. Contact poison treatment specialist
immediately if large quantities have been ingested or inhaled.
Notes to physician
:
:
Protection of first-aiders
:
No action shall be taken involving any personal risk or without suitable training. It may
be dangerous to the person providing aid to give mouth-to-mouth resuscitation.
Use dry chemical,
CO₂,
water spray (fog) or foam.
5. Fire-fighting measures
Extinguishing media
Promptly isolate the scene by removing all persons from the vicinity of the incident if
there is a fire. No action shall be taken involving any personal risk or without suitable
training. Move containers from fire area if this can be done without risk. Use water
spray to keep fire-exposed containers cool.
Flammable liquid. In a fire or if heated, a pressure increase will occur and the container
may burst, with the risk of a subsequent explosion. The vapor/gas is heavier than air
and will spread along the ground. Vapors may accumulate in low or confined areas or
travel a considerable distance to a source of ignition and flash back. Runoff to sewer
may create fire or explosion hazard.
Special protective
equipment for fire-fighters
Fire-fighters should wear appropriate protective equipment and self-contained breathing
apparatus (SCBA) with a full face-piece operated in positive pressure mode.
:
Special exposure hazards
:
Do not use water jet.
Suitable
:
Not suitable
:
Hazardous thermal
decomposition products
:
Decomposition products may include the following materials:
carbon dioxide
carbon monoxide
Flammability of the product
:
No action shall be taken involving any personal risk or without suitable training.
Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilled material. Shut off all ignition sources.
No flares, smoking or flames in hazard area. Avoid breathing vapor or mist. Provide
adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put
on appropriate personal protective equipment (see Section 8).
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Approach release from upwind. Prevent entry into sewers,
water courses, basements or confined areas. Wash spillages into an effluent treatment
plant or proceed as follows. Contain and collect spillage with non-combustible,
absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in
container for disposal according to local regulations (see Section 13). Dispose of via a
licensed waste disposal contractor. Contaminated absorbent material may pose the
same hazard as the spilled product. Note: see Section 1 for emergency contact
information and Section 13 for waste disposal.
Environmental precautions
6. Accidental release measures
:
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).
Personal precautions
:
Large spill
:
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Dilute with water and mop up if water-soluble. Alternatively,
or if water-insoluble, absorb with an inert dry material and place in an appropriate waste
disposal container. Dispose of via a licensed waste disposal contractor.
Small spill
:
Methods for cleaning up
3/13
0710L
9/5/2014.
Page 4
Konform® SR (liquid)
Store in accordance with local regulations. Store in a segregated and approved area.
Store in original container protected from direct sunlight in a dry, cool and well-ventilated
area, away from incompatible materials (see Section 10) and food and drink. Eliminate
all ignition sources. Separate from oxidizing materials. Keep container tightly closed
and sealed until ready for use. Containers that have been opened must be carefully
resealed and kept upright to prevent leakage. Do not store in unlabeled containers.
Use appropriate containment to avoid environmental contamination.
Put on appropriate personal protective equipment (see Section 8). Eating, drinking and
smoking should be prohibited in areas where this material is handled, stored and
processed. Workers should wash hands and face before eating, drinking and smoking.
Remove contaminated clothing and protective equipment before entering eating areas.
Do not ingest. Avoid contact with eyes, skin and clothing. Avoid breathing vapor or mist.
Use only with adequate ventilation. Wear appropriate respirator when ventilation is
inadequate. Do not enter storage areas and confined spaces unless adequately
ventilated. Keep in the original container or an approved alternative made from a
compatible material, kept tightly closed when not in use. Store and use away from heat,
sparks, open flame or any other ignition source. Use explosion-proof electrical
(ventilating, lighting and material handling) equipment. Use non-sparking tools. Take
precautionary measures against electrostatic discharges. To avoid fire or explosion,
dissipate static electricity during transfer by grounding and bonding containers and
equipment before transferring material. Empty containers retain product residue and
can be hazardous. Do not reuse container.
7. Handling and storage
Handling
Storage
:
:
hexane
ACGIH TLV (United States, 4/2014).
TWA: 500 ppm 8 hours.
TWA: 1760 mg/m³ 8 hours.
STEL: 1000 ppm 15 minutes.
STEL: 3500 mg/m³ 15 minutes.
OSHA PEL 1989 (United States, 3/1989).
TWA: 500 ppm 8 hours.
TWA: 1800 mg/m³ 8 hours.
STEL: 1000 ppm 15 minutes.
STEL: 3600 mg/m³ 15 minutes.
NIOSH REL (United States, 10/2013).
TWA: 100 ppm 10 hours.
TWA: 350 mg/m³ 10 hours.
CEIL: 510 ppm 15 minutes.
CEIL: 1800 mg/m³ 15 minutes.
toluene
ACGIH TLV (United States, 4/2014).
TWA: 20 ppm 8 hours.
NIOSH REL (United States, 10/2013).
STEL: 560 mg/m³ 15 minutes.
STEL: 150 ppm 15 minutes.
TWA: 375 mg/m³ 10 hours.
TWA: 100 ppm 10 hours.
OSHA PEL 1989 (United States, 3/1989).
STEL: 560 mg/m³ 15 minutes.
STEL: 150 ppm 15 minutes.
TWA: 375 mg/m³ 8 hours.
TWA: 100 ppm 8 hours.
OSHA PEL Z2 (United States, 2/2013).
AMP: 500 ppm 10 minutes.
CEIL: 300 ppm
TWA: 200 ppm 8 hours.
2,2-dimethylbutane
ACGIH TLV (United States, 4/2014).
8. Exposure controls/personal protection
Ingredient
Exposure limits
4/13
0710L
9/5/2014.
Page 5
Konform® SR (liquid)
8. Exposure controls/personal protection
TWA: 500 ppm 8 hours.
TWA: 1760 mg/m³ 8 hours.
STEL: 1000 ppm 15 minutes.
STEL: 3500 mg/m³ 15 minutes.
OSHA PEL 1989 (United States, 3/1989).
TWA: 500 ppm 8 hours.
TWA: 1800 mg/m³ 8 hours.
STEL: 1000 ppm 15 minutes.
STEL: 3600 mg/m³ 15 minutes.
NIOSH REL (United States, 10/2013).
TWA: 100 ppm 10 hours.
TWA: 350 mg/m³ 10 hours.
CEIL: 510 ppm 15 minutes.
CEIL: 1800 mg/m³ 15 minutes.
2,3-dimethylbutane
ACGIH TLV (United States, 4/2014).
TWA: 500 ppm 8 hours.
TWA: 1760 mg/m³ 8 hours.
STEL: 1000 ppm 15 minutes.
STEL: 3500 mg/m³ 15 minutes.
OSHA PEL 1989 (United States, 3/1989).
TWA: 500 ppm 8 hours.
TWA: 1800 mg/m³ 8 hours.
STEL: 1000 ppm 15 minutes.
STEL: 3600 mg/m³ 15 minutes.
NIOSH REL (United States, 10/2013).
TWA: 100 ppm 10 hours.
TWA: 350 mg/m³ 10 hours.
CEIL: 510 ppm 15 minutes.
CEIL: 1800 mg/m³ 15 minutes.
3-methylpentane
ACGIH TLV (United States, 4/2014).
TWA: 500 ppm 8 hours.
TWA: 1760 mg/m³ 8 hours.
STEL: 1000 ppm 15 minutes.
STEL: 3500 mg/m³ 15 minutes.
OSHA PEL 1989 (United States, 3/1989).
TWA: 500 ppm 8 hours.
TWA: 1800 mg/m³ 8 hours.
STEL: 1000 ppm 15 minutes.
STEL: 3600 mg/m³ 15 minutes.
NIOSH REL (United States, 10/2013).
TWA: 100 ppm 10 hours.
TWA: 350 mg/m³ 10 hours.
CEIL: 510 ppm 15 minutes.
CEIL: 1800 mg/m³ 15 minutes.
acetone
ACGIH TLV (United States, 4/2014).
STEL: 1782 mg/m³ 15 minutes.
STEL: 750 ppm 15 minutes.
TWA: 1188 mg/m³ 8 hours.
TWA: 500 ppm 8 hours.
NIOSH REL (United States, 10/2013).
TWA: 590 mg/m³ 10 hours.
TWA: 250 ppm 10 hours.
OSHA PEL (United States, 2/2013).
TWA: 2400 mg/m³ 8 hours.
TWA: 1000 ppm 8 hours.
OSHA PEL 1989 (United States, 3/1989).
STEL: 2400 mg/m³ 15 minutes.
STEL: 1000 ppm 15 minutes.
TWA: 1800 mg/m³ 8 hours.
5/13
0710L
9/5/2014.
Page 6
Konform® SR (liquid)
8. Exposure controls/personal protection
TWA: 750 ppm 8 hours.
2-methoxy-1-methylethyl acetate
AIHA WEEL (United States, 10/2011).
TWA: 50 ppm 8 hours.
n-hexane
ACGIH TLV (United States, 4/2014). Absorbed through skin.
TWA: 50 ppm 8 hours.
NIOSH REL (United States, 10/2013).
TWA: 180 mg/m³ 10 hours.
TWA: 50 ppm 10 hours.
OSHA PEL (United States, 2/2013).
TWA: 1800 mg/m³ 8 hours.
TWA: 500 ppm 8 hours.
OSHA PEL 1989 (United States, 3/1989).
TWA: 180 mg/m³ 8 hours.
TWA: 50 ppm 8 hours.
Use a properly fitted, air-purifying or air-fed respirator complying with an approved
standard if a risk assessment indicates this is necessary. Respirator selection must be
based on known or anticipated exposure levels, the hazards of the product and the safe
working limits of the selected respirator.
Safety eyewear complying with an approved standard should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists or
dusts. If contact is possible, the following protection should be worn, unless the
assessment indicates a higher degree of protection: chemical splash goggles.
Personal protective equipment for the body should be selected based on the task being
performed and the risks involved and should be approved by a specialist before
handling this product.
When there is a risk of ignition from static electricity, wear anti-static protective clothing.
For the greatest protection from static discharges, clothing should include anti-static
overalls, boots and gloves.
Personal protection
Eyes
Skin
Respiratory
:
:
:
Chemical-resistant, impervious gloves complying with an approved standard should be
worn at all times when handling chemical products if a risk assessment indicates this is
necessary. Considering the parameters specified by the glove manufacturer, check
during use that the gloves are still retaining their protective properties. It should be
noted that the time to breakthrough for any glove material may be different for different
glove manufacturers. In the case of mixtures, consisting of several substances, the
protection time of the gloves cannot be accurately estimated.
Hands
:
Engineering measures
:
Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or
other engineering controls to keep worker exposure to airborne contaminants below any
recommended or statutory limits. The engineering controls also need to keep gas,
vapor or dust concentrations below any lower explosive limits. Use explosion-proof
ventilation equipment.
Hygiene measures
:
Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Wash contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Recommended monitoring
procedures
:
If this product contains ingredients with exposure limits, personal, workplace
atmosphere or biological monitoring may be required to determine the effectiveness of
the ventilation or other control measures and/or the necessity to use respiratory
protective equipment. Reference should be made to appropriate monitoring standards.
Reference to national guidance documents for methods for the determination of
hazardous substances will also be required.
Environmental exposure
controls
:
Emissions from ventilation or work process equipment should be checked to ensure
they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process equipment
will be necessary to reduce emissions to acceptable levels.
6/13
0710L
9/5/2014.
Page 7
Konform® SR (liquid)
54°C (129.2°F)
Liquid.
85% (v/v)
0.74
>1 [Air = 1]
Hydrocarbon.
Translucent. Light Green.
Boiling/condensation point
>1 (butyl acetate = 1)
9. Physical and chemical properties
Physical state
Relative density
Vapor density
Volatility
Evaporation rate
Odor
Color::::
:
:
:
:
Flash point
:
Closed cup: 16°C (60.8°F) [Tagliabue.]
The product is stable.
Reactive or incompatible with the following materials: oxidizing materials alkalis
Under normal conditions of storage and use, hazardous decomposition products should
not be produced.
Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld,
braze, solder, drill, grind or expose containers to heat or sources of ignition. Do not
allow vapor to accumulate in low or confined areas.
10. Stability and reactivity
Chemical stability
Conditions to avoid
Incompatible materials
Hazardous decomposition
products
:::
:
Possibility of hazardous
reactions
:
Under normal conditions of storage and use, hazardous reactions will not occur.
11. Toxicological information
Acute toxicity
toluene
LC50 Inhalation Vapor
Rat
49 g/m³
4 hours
LD50 Oral
Rat
636 mg/kg
-
acetone
LD50 Oral
Rat
5800 mg/kg
-
2-methoxy-1-methylethyl
acetate
LD50 Dermal
Rabbit
>5 g/kg
-
LD50 Oral
Rat
8532 mg/kg
-
n-hexane
LC50 Inhalation Gas.
Rat
48000 ppm
4 hours
LD50 Oral
Rat
15840 mg/kg
-
Product/ingredient name
Result
Species
Dose
Exposure
Conclusion/Summary
:
Not available.
Chronic toxicity
Conclusion/Summary
:
Not available.
Irritation/Corrosion
Product/ingredient name
Result
Score
Exposure
Observation
Species
toluene
Eyes - Mild irritant
Rabbit
-
0.5 minutes
100
milligrams
-
Eyes - Mild irritant
Rabbit
-
870
Micrograms
-
Eyes - Severe irritant
Rabbit
-
24 hours 2
milligrams
-
Skin - Mild irritant
Pig
-
24 hours 250
microliters
-
Skin - Mild irritant
Rabbit
-
435
milligrams
-
Skin - Moderate irritant
Rabbit
-
24 hours 20
milligrams
-
7/13
0710L
9/5/2014.
Page 8
Konform® SR (liquid)
11. Toxicological information
Carcinogenicity
Conclusion/Summary
:
Not available.
Mutagenicity
Conclusion/Summary
:
Not available.
Teratogenicity
Conclusion/Summary
:
Not available.
Reproductive toxicity
Conclusion/Summary
:
Not available.
Classification
toluene
-3-A4-
None.
acetone
---A4-
None.
2-methoxy-1-methylethyl
acetate
-----
None.
Product/ingredient name
ACGIH
EPA
NIOSH
NTP
IARC
OSHA
Conclusion/Summary
:
Not available.
Sensitizer
Conclusion/Summary
:
Not available.
Skin - Moderate irritant
Rabbit
-
500
milligrams
-
acetone
Eyes - Mild irritant
Human
-
186300 parts
per million
-
Eyes - Mild irritant
Rabbit
-
10 microliters
-
Eyes - Moderate irritant
Rabbit
-
24 hours 20
milligrams
-
Eyes - Severe irritant
Rabbit
-
20 milligrams
-
Skin - Mild irritant
Rabbit
-
24 hours 500
milligrams
-
Skin - Mild irritant
Rabbit
-
395
milligrams
-
n-hexane
Eyes - Mild irritant
Rabbit
-
10 milligrams
-
12. Ecological information
Ecotoxicity
:
No known significant effects or critical hazards.
Aquatic ecotoxicity
toluene
Acute EC50 433 ppm Marine water
Algae - Skeletonema costatum
96 hours
Acute EC50 12500 µg/l Fresh water
Algae - Pseudokirchneriella
subcapitata
72 hours
Acute EC50 11600 µg/l Fresh water
Crustaceans - Gammarus
pseudolimnaeus - Adult
48 hours
Acute EC50 6000 µg/l Fresh water
Daphnia - Daphnia magna Juvenile (Fledgling, Hatchling,
Weanling)
48 hours
Acute LC50 5500 µg/l Fresh water
Fish - Oncorhynchus kisutch - Fry
96 hours
Chronic NOEC 500000 µg/l Fresh water
Algae - Pseudokirchneriella
subcapitata
96 hours
Chronic NOEC 1000 µg/l Fresh water
Daphnia - Daphnia magna
21 days
acetone
Acute EC50 20.565 mg/l Marine water
Algae - Ulva pertusa
96 hours
Acute LC50 6000000 µg/l Fresh water
Crustaceans - Gammarus pulex
48 hours
Acute LC50 10000 µg/l Fresh water
Daphnia - Daphnia magna
48 hours
Acute LC50 100 mg/l Fresh water
Fish - Pimephales promelas Juvenile (Fledgling, Hatchling,
96 hours
Product/ingredient name
Species
Result
Exposure
8/13
0710L
9/5/2014.
Page 9
Konform® SR (liquid)
12. Ecological information
Weanling)
Chronic NOEC 4.95 mg/l Marine water
Algae - Ulva pertusa
96 hours
Chronic NOEC 0.016 ml/L Fresh water
Crustaceans - Daphniidae
21 days
Chronic NOEC 0.1 ml/L Fresh water
Daphnia - Daphnia magna Neonate
21 days
Chronic NOEC 5 µg/l Marine water
Fish - Gasterosteus aculeatus Larvae
42 days
n-hexane
Acute LC50 113000 µg/l Fresh water
Fish - Oreochromis
mossambicus
96 hours
Conclusion/Summary
:
Not available.
Persistence/degradability
Conclusion/Summary
:
Not available.
Other adverse effects
:
No known significant effects or critical hazards.
The generation of waste should be avoided or minimized wherever possible. Disposal
of this product, solutions and any by-products should at all times comply with the
requirements of environmental protection and waste disposal legislation and any
regional local authority requirements. Dispose of surplus and non-recyclable products
via a licensed waste disposal contractor. Waste should not be disposed of untreated to
the sewer unless fully compliant with the requirements of all authorities with jurisdiction.
Waste packaging should be recycled. Incineration or landfill should only be considered
when recycling is not feasible. This material and its container must be disposed of in a
safe way. Care should be taken when handling emptied containers that have not been
cleaned or rinsed out. Empty containers or liners may retain some product residues.
Vapor from product residues may create a highly flammable or explosive atmosphere
inside the container. Do not cut, weld or grind used containers unless they have been
cleaned thoroughly internally. Avoid dispersal of spilled material and runoff and contact
with soil, waterways, drains and sewers.
Waste disposal
13. Disposal considerations
Disposal should be in accordance with applicable regional, national and local laws and regulations.
:
Refer to Section 7: HANDLING AND STORAGE and Section 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
for additional handling information and protection of employees.
United States - RCRA Toxic hazardous waste "U" List
Toluene; Benzene, methyl-
108-88-3
Listed
U220
Acetone (I); 2-Propanone (I)
67-64-1
Listed
U002
Ingredient
CAS #
Status
Reference
number
14. Transport information
3
Reportable quantity
8000 lbs / 3632 kg
[1296.6 gal / 4908.1 L]
Package sizes
shipped in quantities
less than the product
reportable quantity are
not subject to the RQ
(reportable quantity)
transportation
requirements.
DOT Classification
Coating Solution
II
Regulatory
information
UN number
Proper shipping
name
Classes
PG*
Label
Additional
information
UN1139
9/13
0710L
9/5/2014.
Page 10
Konform® SR (liquid)
14. Transport information
TDG Classification
3
UN1139
Coating Solution
II
ADR/RID Class
Coating Solution
3IIIMDG Class
Coating Solution
3
II
Coating Solution
UN1139
IATA-DGR Class
3
II
UN1139
UN1139
-
-
-
-
Mexico
Classification
UN1139
Coating Solution
3II-
PG* : Packing group
Flammable liquid
Irritating material
Target organ effects
HCS Classification
15. Regulatory information
U.S. Federal regulations
Clean Water Act (CWA) 307
: toluene
Clean Water Act (CWA) 311
: toluene
:
:
Clean Air Act Section 112
(b) Hazardous Air
Pollutants (HAPs)
:
Listed
Clean Air Act Section 602
Class I Substances
:
Not listed
Clean Air Act Section 602
Class II Substances
:
Not listed
DEA List I Chemicals
(Precursor Chemicals)
:
Not listed
DEA List II Chemicals
(Essential Chemicals)
:
Listed
TSCA 8(a) PAIR
: 2-methoxy-1-methylethyl acetate
TSCA 8(a) CDR Exempt/Partial exemption
: Not determined
All components are listed or exempted.
SARA 302/304
SARA 304 RQ
:
Not applicable.
No products were found.
Composition/information on ingredients
SARA 311/312
Classification
:
Fire hazard
Immediate (acute) health hazard
Delayed (chronic) health hazard
10/13
0710L
9/5/2014.
Page 11
Konform® SR (liquid)
15. Regulatory information
The following components are listed: 3-METHYLPENTANE; ISOHEXANE; 2,
3-DIMETHYLBUTANE; 2,2-DIMETHYLBUTANE; TOLUENE; ACETONE; HEXANE
WARNING:
This product contains a chemical known to the State of California to cause birth defects or other
reproductive harm.
Massachusetts
International regulations
:
SARA 313
Product name
CAS number
%
SARA 313 notifications must not be detached from the MSDS and any copying and redistribution of the MSDS shall
include copying and redistribution of the notice attached to copies of the MSDS subsequently redistributed.
toluene
No.
Yes.
No.
7000 µg/day
(ingestion)
13000 µg/day
(inhalation)
Ingredient name
Cancer
Reproductive
No significant risk
level
Maximum
acceptable dosage
level
toluene
108-88-3
10 - 15
n-hexane
110-54-3
1 - 2
toluene
108-88-3
10 - 15
n-hexane
110-54-3
1 - 2
Form R - Reporting
requirements
Supplier notification
California Prop. 65
Canada inventory
:
All components are listed or exempted.
New York
:
The following components are listed: Toluene; Acetone; 2-Propanone; Hexane
New Jersey
:
The following components are listed: 2-METHYLPENTANE; ISOHEXANE; 2,
3-DIMETHYLBUTANE; BUTANE, 2,3-DIMETHYL-; NEOHEXANE; 2,2 DIMETHYL
BUTANE; TOLUENE; BENZENE, METHYL-; ACETONE; 2-PROPANONE; n-HEXANE;
HEXANE
Pennsylvania
:
The following components are listed: PENTANE, 3-METHYL-; PENTANE, 2-METHYL-;
BUTANE, 2,3-DIMETHYL-; BUTANE, 2,2-DIMETHYL-; BENZENE, METHYL-;
2-PROPANONE; HEXANE
State regulations
3-methylpentane
10 - 15
Yes.
No.
No.
No.
Yes.
hexane
20 - 40
Yes.
No.
No.
No.
Yes.
2,3-dimethylbutane
10 - 15
Yes.
No.
No.
No.
Yes.
2,2-dimethylbutane
10 - 15
No.
No.
No.
No.
Yes.
toluene
10 - 15
Yes.
No.
No.
Yes.
Yes.
acetone
5 - 10
Yes.
No.
No.
Yes.
Yes.
2-methoxy-1-methylethyl acetate
3 - 8
Yes.
No.
No.
No.
Yes.
n-hexane
1 - 2
Yes.
No.
No.
Yes.
Yes.
Name
%
Fire
hazard
Sudden
release of
pressure
Reactive
Immediate
(acute)
health
hazard
Delayed
(chronic)
health
hazard
Composition/information on ingredients
11/13
0710L
9/5/2014.
Page 12
Konform® SR (liquid)
15. Regulatory information
Australia inventory (AICS)
: All components are listed or exempted.
China inventory (IECSC)
: All components are listed or exempted.
Japan inventory
: Not determined.
Korea inventory
: All components are listed or exempted.
Malaysia Inventory (EHS Register)
: Not determined.
New Zealand Inventory of Chemicals (NZIoC)
: All components are listed or exempted.
Philippines inventory (PICCS)
: All components are listed or exempted.
Taiwan inventory (CSNN)
: Not determined.
International lists
:
Chemical Weapons
Convention List Schedule
I Chemicals
:
Not listed
Chemical Weapons
Convention List Schedule
II Chemicals
:
Not listed
Chemical Weapons
Convention List Schedule
III Chemicals
:
Not listed
16. Other information
Hazardous Material
Information System (U.S.A.)
2
3
1
132
National Fire Protection
Association (U.S.A.)
Health
Special
Instability/Reactivity
Flammability
Health
Flammability
Physical hazards
FLAMMABLE LIQUID AND VAPOR. CAUSES EYE AND SKIN IRRITATION. MAY BE
HARMFUL IF SWALLOWED. CONTAINS MATERIAL THAT MAY CAUSE TARGET
ORGAN DAMAGE, BASED ON ANIMAL DATA.
Label requirements
:
Date of printing
9/5/2014.
:
:
:
Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4
representing significant hazards or risks Although HMIS® ratings are not required on MSDSs under 29 CFR 1910.
1200, the preparer may choose to provide them. HMIS® ratings are to be used with a fully implemented HMIS®
program. HMIS® is a registered mark of the National Paint & Coatings Association (NPCA). HMIS® materials may
be purchased exclusively from J. J. Keller (800) 327-6868.
The customer is responsible for determining the PPE code for this material.
Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency
Response Copyright ©1997, National Fire Protection Association, Quincy, MA 02269. This reprinted material is not
the complete and official position of the National Fire Protection Association, on the referenced subject which is
represented only by the standard in its entirety.
Copyright ©2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to be
interpreted and applied only by properly trained individuals to identify fire, health and reactivity hazards of
chemicals. The user is referred to certain limited number of chemicals with recommended classifications in NFPA
49 and NFPA 325, which would be used as a guideline only. Whether the chemicals are classified by NFPA or not,
anyone using the 704 systems to classify chemicals does so at their own risk.
12/13
0710L
9/5/2014.
Page 13
Konform® SR (liquid)
16. Other information
Notice to reader
To the best of our knowledge, the information contained herein is accurate. However, neither the above-named
supplier, nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the
information contained herein.
Final determination of suitability of any material is the sole responsibility of the user. All materials may present
unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot
guarantee that these are the only hazards that exist.
Date of issue
Date of previous issue
Version
:::
Indicates information that has changed from previously issued version.
9/5/2014.
9/5/2014.
1.01
Prepared by
:
Not available.
13/13
0710L
9/5/2014.
Loading...