
Chemtronics
8125 Cobb Center Drive
Kennesaw, GA 30152
Tel. 770-424-4888 or toll free 800-645-5244
Chemtrec - 1-800-424-9300 or collect 703-527-3887
24/7
Chemtronics
8125 Cobb Center Drive
Kennesaw, GA 30152
Tel. 770-424-4888 or toll free 800-645-5244
Material Safety Data Sheet
1. Product and company identification
2. Hazards identification
Potential acute health effects
No known significant effects or critical hazards.
No known significant effects or critical hazards.
No known significant effects or critical hazards.
No known significant effects or critical hazards.
NOT EXPECTED TO PRODUCE SIGNIFICANT ADVERSE HEALTH EFFECTS WHEN
THE RECOMMENDED INSTRUCTIONS FOR USE ARE FOLLOW ED.
Characteristic. Ethereal. [Slight]
While this material is not considered hazardous by the OSHA Hazard Communication
Standard (29 CFR 1910.1200), this MSDS contains valuable information critical to the
safe handling and proper use of the product. This MSDS should be retained and
available for employees and other users of this product.
Potential chronic health effects
No known significant effects or critical hazards.
No known significant effects or critical hazards.
No known significant effects or critical hazards.
No known significant effects or critical hazards.
No known significant effects or critical hazards.
No known significant effects or critical hazards.
Over-exposure signs/symptoms

2. Hazards identification
See toxicological information (Section 11)
Medical conditions
aggravated by overexposure
3. Composition/information on ingredients
There are no ingredients present which, within the current knowledge of the supplier and in the concentrations
applicable, are classified as hazardous to health or the environment and hence require reporting in this section.
Wash out mouth with water. Do not induce vomiting unless directed to do so by medical
personnel. Never give anything by mouth to an unconscious person. Get medical
attention if symptoms occur.
Check for and remove any contact lenses. Immediately flush eyes with plenty of water
for at least 15 minutes, occasionally lifting the upper and lower eyelids. Get medical
attention if symptoms occur.
In case of contact, immediately flush skin with plenty of water for at least 15 minutes
while removing contaminated clothing and shoes. Wash clothing before reuse. Clean
shoes thoroughly before reuse. Get medical attention if symptoms occur.
Move exposed person to fresh air. If not breathing, if breathing is irregular or if
respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel.
Loosen tight clothing such as a collar, tie, belt or waistband. Get medical attention if
symptoms occur.
No specific treatment. Treat symptomatically. Contact poison treatment specialist
immediately if large quantities have been ingested or inhaled.
Protection of first-aiders
No action shall be taken involving any personal risk or without suitable training.
Use an extinguishing agent suitable for the surrounding fire.
5. Fire-fighting measures
Promptly isolate the scene by removing all persons from the vicinity of the incident if
there is a fire. No action shall be taken involving any personal risk or without suitable
training.
In a fire or if heated, a pressure increase will occur and the container may burst.
Special protective
equipment for fire-fighters
Fire-fighters should wear appropriate protective equipment and self-contained breathing
apparatus (SCBA) with a full face-piece operated in positive pressure mode.
Hazardous thermal
decomposition products
Decomposition products may include the following materials:
carbon dioxide
carbon monoxide
Flammability of the product

No action shall be taken involving any personal risk or without suitable training.
Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilled material. Put on appropriate personal
protective equipment (see Section 8).
Stop leak if without risk. Move containers from spill area. Prevent entry into sewers,
water courses, basements or confined areas. Wash spillages into an effluent treatment
plant or proceed as follows. Contain and collect spillage with non-combustible,
absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in
container for disposal according to local regulations (see Section 13). Dispose of via a
licensed waste disposal contractor. Note: see Section 1 for emergency contact
information and Section 13 for waste disposal.
Environmental precautions
6. Accidental release measures
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).
Stop leak if without risk. Move containers from spill area. Dilute with water and mop up
if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and
place in an appropriate waste disposal container. Dispose of via a licensed waste
disposal contractor.
Store in accordance with local regulations. Store in original container protected from
direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials
(see Section 10) and food and drink. Keep container tightly closed and sealed until
ready for use. Containers that have been opened must be carefully resealed and kept
upright to prevent leakage. Do not store in unlabeled containers. Use appropriate
containment to avoid environmental contamination.
Put on appropriate personal protective equipment (see Section 8). Eating, drinking and
smoking should be prohibited in areas where this material is handled, stored and
processed. Workers should wash hands and face before eating, drinking and smoking.
Remove contaminated clothing and protective equipment before entering eating areas.
8. Exposure controls/personal protection
Use a properly fitted, air-purifying or air-fed respirator complying with an approved
standard if a risk assessment indicates this is necessary. Respirator selection must be
based on known or anticipated exposure levels, the hazards of the product and the safe
working limits of the selected respirator.
Consult local authorities for acceptable exposure limits.
Good general ventilation should be sufficient to control worker exposure to airborne
contaminants.
Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Wash contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Recommended monitoring
procedures
If this product contains ingredients with exposure limits, personal, workplace
atmosphere or biological monitoring may be required to determine the effectiveness of
the ventilation or other control measures and/or the necessity to use respiratory
protective equipment. Reference should be made to appropriate monitoring standards.
Reference to national guidance documents for methods for the determination of
hazardous substances will also be required.

8. Exposure controls/personal protection
Safety eyewear complying with an approved standard should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists or
dusts. If contact is possible, the following protection should be worn, unless the
assessment indicates a higher degree of protection: safety glasses with side-shields.
Personal protective equipment for the body should be selected based on the task being
performed and the risks involved and should be approved by a specialist before
handling this product.
Chemical-resistant, impervious gloves complying with an approved standard should be
worn at all times when handling chemical products if a risk assessment indicates this is
necessary.
Environmental exposure
controls
Emissions from ventilation or work process equipment should be checked to ensure
they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process equipment
will be necessary to reduce emissions to acceptable levels.
Characteristic. Ethereal. [Slight]
9. Physical and chemical properties
Under normal conditions of storage and use, hazardous decomposition products should
not be produced.
10. Stability and reactivity
Hazardous decomposition
products
Possibility of hazardous
reactions
Under normal conditions of storage and use, hazardous reactions will not occur.
11. Toxicological information

12. Ecological information
No known significant effects or critical hazards.
Persistence/degradability
No known significant effects or critical hazards.
The generation of waste should be avoided or minimized wherever possible. Disposal
of this product, solutions and any by-products should at all times comply with the
requirements of environmental protection and waste disposal legislation and any
regional local authority requirements. Dispose of surplus and non-recyclable products
via a licensed waste disposal contractor. Waste should not be disposed of untreated to
the sewer unless fully compliant with the requirements of all authorities with jurisdiction.
Waste packaging should be recycled. Incineration or landfill should only be considered
when recycling is not feasible. This material and its container must be disposed of in a
safe way. Empty containers or liners may retain some product residues. Avoid
dispersal of spilled material and runoff and contact with soil, waterways, drains and
sewers.
13. Disposal considerations
Disposal should be in accordance with applicable regional, national and local laws and regulations.
Refer to Section 7: HANDLING AND STORAGE and Section 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
for additional handling information and protection of employees.
14. Transport information
15. Regulatory information
Clean Water Act (CWA) 311
: triethylamine
: (2-methoxymethylethoxy)propanol
TSCA 8(a) CDR Exempt/Partial exemption
: Not determined
United States inventory (TSCA 8b)
: All components are listed or exempted.

15. Regulatory information
None of the components are listed.
Australia inventory (AICS)
: All components are listed or exempted.
China inventory (IECSC)
: All components are listed or exempted.
Japan inventory
: All components are listed or exempted.
Korea inventory
: All components are listed or exempted.
Malaysia Inventory (EHS Register)
: Not determined.
New Zealand Inventory of Chemicals (NZIoC)
: All components are listed or exempted.
Philippines inventory (PICCS)
: All components are listed or exempted.
Taiwan inventory (CSNN)
: Not determined.
International regulations
All components are listed or exempted.
Clean Air Act Section 112
(b) Hazardous Air
Pollutants (HAPs)
Clean Air Act Section 602
Class I Substances
Clean Air Act Section 602
Class II Substances
DEA List I Chemicals
(Precursor Chemicals)
DEA List II Chemicals
(Essential Chemicals)
Chemical Weapons
Convention List Schedule
I Chemicals
Chemical Weapons
Convention List Schedule
II Chemicals
Chemical Weapons
Convention List Schedule
III Chemicals
None of the components are listed.
None of the components are listed.
None of the components are listed.
Composition/information on ingredients
Composition/information on ingredients

Hazardous Material
Information System (U.S.A.)
National Fire Protection
Association (U.S.A.)
NOT EXPECTED TO PRODUCE SIGNIFICANT ADVERSE HEALTH EFFECTS WHEN
THE RECOMMENDED INSTRUCTIONS FOR USE ARE FOLLOW ED.
To the best of our knowledge, the information contained herein is accurate. However, neither the above-named
supplier, nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the
information contained herein.
Final determination of suitability of any material is the sole responsibility of the user. All materials may present
unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot
guarantee that these are the only hazards that exist.
Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4
representing significant hazards or risks Although HMIS® ratings are not required on MSDSs under 29 CFR 1910.
1200, the preparer may choose to provide them. HMIS® ratings are to be used with a fully implemented HMIS®
program. HMIS® is a registered mark of the National Paint & Coatings Association (NPCA). HMIS® materials may
be purchased exclusively from J. J. Keller (800) 327-6868.
The customer is responsible for determining the PPE code for this material.
Indicates information that has changed from previously issued version.
Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency
Response Copyright ©1997, National Fire Protection Association, Quincy, MA 02269. This reprinted material is not
the complete and official position of the National Fire Protection Association, on the referenced subject which is
represented only by the standard in its entirety.
Copyright ©2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to be
interpreted and applied only by properly trained individuals to identify fire, health and reactivity hazards of
chemicals. The user is referred to certain limited number of chemicals with recommended classifications in NFPA
49 and NFPA 325, which would be used as a guideline only. Whether the chemicals are classified by NFPA or not,
anyone using the 704 systems to classify chemicals does so at their own risk.