Chemtronics CTFC5 User Manual

of Cured Coatings (-35°C to 100°C)
followed by 10 min @ 80°C
Specific Gravity 0.72 (Water=1) @ 68°F (Liquid Only)
Coverage 1 gallon 254.0 (1 mil/ft2) 12oz 20.2
RoHS Compliant
VOC Content
TDS # CTFC1
CHEMTRONICS
Technical Data Sheet
Konform® Flexcoat
Flexible Conformal Coating
PRODUCT DESCRIPTION
Konform Flexcoat Conformal Coating is designed for applications where flexibility and protection are paramount. This material is as flexible as an RTV silicone, but without the disadvantages of a silicone. Providing a soft, rubbery protective coating, this material will coat evenly and provide a flexible and durable protective barrier against humidity, salt, corrosive vapors and fungus for printed circuit board and electronic assemblies. This coating can be removed by cutting a small section and peeling the coating away from the surface, or by solvent immersion of the whole board. meets IPC-CC-830B Class B.
Coating
Extremely flexible silicone free conformal
coating
Clear, durable coating Very good dielectric strength prevents arcing
and current leakage
Increases life of electronic assemblies Will not discolor over time under normal use Contains a UV indicator for Qualit y Control
inspection using medium intensity light at 265-335 nm
TYPICAL APPLICATIONS
Konform Flexcoat Conformal Coating is ideal for applications in:
Data Communications Instrumentation Automotive Manufacturing Marine Manufacturing Process Control
TYPICAL PRODUCT DATA AND PHYSICAL PROPERTIES
Usable Temp. Range -31°F to 212°F
Tack Free Time 30 min.
Curing Conditions 24 Hours @ 77°F (25°C) (@ 80% R.H.) 8 Hours @ 150°F (65°C)
Quick Cure 10 min. @RT
Viscosity (cps @ 77°F) 24± 5 cps
Flash Point (TCC) 30°F
Dielectric Strength 956 volts/mil
Dielectric Breakdown (volts/mil) 2550
Shelf life 2 years
CARB & OTC VOC Content
SCAQMD
*Volatile Organic Compound (VOC) information is calculated on a weight basis using the VOC definition of California Air Resources Board (CARB) Consumer Product Regulations, South Coast Air Quality Management District (SCAQMD) Rule 102 and the Federal definition published in 40 CFR 51.100(s).
640 g/L (liquid)
88.9% VOC
COMPATIBILITY
Konform Flexcoat Conformal Coating is genera lly compatible with most materials found on printed circuit boards. As with any chemical product,
product/component compatibility must be
Performance
Moisture Resistance
Good
Removability
Excellent
Ease of Repair
Excellent
Flexibility
Excellent
Adhesion
Good
Abrasion Resistance
Fair
Solvent Resistance
Fair
determined on a non-critical area prior to use.
USAGE INSTRUCTIONS
For industrial use only. Read MSDS carefully prior to use. Before applying Konform clean circuit boards thoroughly to remove oil, grease, dirt, flux and all other types of contamination. Allow to dry. Cleaning may be performed with Chemtronics Electro-Wash
SPRAY APPLICATION: Apply top to bottom, allowing coating to flow evenly around components. Rotate PCB 90° and r epeat application. Rotate and apply coating two additional times, then allow board to cure. If additional thickness is desired, apply additional coatings. When using liquid spray with automatic dispensing equipment, adjustments may be required in application rate and viscosity.
DIP APPLICATION: Using automatic equipment or hand immersion technique, slowly immerse PCB into the coating and remove slowly. Use an average rate of approximately 1 foot per minute. After allowing the board to cure, process may be repeated to achieve desired thickness.
BRUSH APPLICATIONS: Evenly apply coating to areas desired at thickness required. Allow time for curing before reapplying to achieve a thick coating. Use Chemask coating process.
CURING: Tack free time is 30 minutes at room temperature. Accelerated curing can be obtained by heating for 10 minutes @ 80 environments. Optimum cure cycles using radiant or convection conveyer ovens are best determined experimentally. Product may also be cured for 24 hours @ 77
accelerated cures as the product solvents are flammable.
REMOVAL: After application, cured Konform
Flexcoat Conformal Coating may be re move d b y peeling, or soaking in Chemtronics Electro-Wash
or Eco-Rite™ degreasing products.
to protect components during conformal
o
F (25oC). NOTE: Care must taken with
Flexcoat Conformal Coating,
o
C in well ventilated
Two Step.
AVAILABILITY CTFC-12 11.5 oz. Aerosol CTFC1 1 Gallon Liquid CTFC5 5 Gallon Liquid CTFC55 55 Gallon Liquid
TECHNICAL & APPLICATION ASSISTANCE
Chemtronics provides a technical hotline to answer your technical and application related questions. The toll free number is: 1-800-TECH-401.
NOTE: This information is believed to be accurate. It
is intended for professional end users having the skills to evaluate and use the data properly. CHEMTRONICS does not guarantee the accuracy of the data and assumes no liability in connection with damages incurred while using it.
CHEMTRONICS 8125 COBB CENTER DRIVE KENNESAW, GA 30152 1-770-424-4888
Chemtronics, Chemask, Konform® and Electro-Wash are registered trademarks of Chemtronics. All rights reserved. Eco-Rite™ is a trademark of Chemtronics. All rights reserved.
DISTRIBUTED BY:
REV. B (08/13)
Loading...