Chemtronics 6259BESD User Manual
COVENTRY
Clean Room Products
Poly-Onyx™ Wipes
PRODUCT DESCRIPTION
Poly-Onyx™ ESD Wipes ESD combine several
advancements and desirable features into one
wipe. They are made from black monofilament
polyester no-run knit, providing excellent strength,
good absorbency and chemical compatibility.
These wipers are a good choice for general clean
room and equipment maintenance, or any critical
applications where lint can be detrimental.
However, their black color makes them especially
valuable as an inspection wipe for translucent or
light colored soils and dusts; as well as for makeup on clean room workers. Special static
dissipative fibers are also woven into the fabric to
safely relieve potentially damaging static charge.
Excellent solvent and acid resistance
Monofilament "no-run" construction does not
generate loose fibers
Excellent durability for cleaning rough,
abrasive, or irregular surfaces
Low ionic, nonvolatile residue and particle
contamination
Good absorbency
Available stacked and vacuum packed
Laser sealed edge
Static Dissipative
Class 100 – 1000 (ISO 5-6) Clean room
TYPICAL APPLICATIONS
Poly-Wipes can be used to clean:
Semiconductor Wafer Fabs
Aerospace Production Areas
Disk Drives Production Areas
Pharmaceutical / Biotechnical Production Areas
General Clean room Cleaning
Dust and Make-up Detection / Inspection
Clean static sensitive surfaces
.
COMPATIBILITY
Poly-Onyx™ ESD Wipes are compatible with
most common solvents such as isopropyl alcohol,
methanol and ketones such as acetone or methyl
ethyl ketone. These wipes are generally
compatible with dilute or weak bases, as well as
with most dilute or weak acids.
AVAILABILITY
6259BESD 9" x 9" (22.9cm x 22.9cm)
Black, Laser Sealed Edge
Polyester wipe,140g/m2,
150/Bag
MANUFACTURED BY:
COVENTRY™ Clean Room Products
Division of ITW Chemtronics® Inc.
8125 Cobb Center Drive
Kennesaw, GA 30152 USA
1-770-424-4888 REV. A (02/10)
Division of ITW Chemtronics ® Inc.
TDS # 6259BESD
TECHNICAL HOT LINE 1-800-TECH-401
Wipe Material
Poly-Onyx™ Wipes Test Data
Black ESD Polyester Knit Fabric
Wipe
Availability
Basis Weight
Particle Counts (LPC)
>/= 0.5 microns
NVR in DI water
NVR in IPA
FTIR : silicone, amide, phthalates
Chloride Ions
Nitrite Ions
Nitrate Ions
Sulphate Ions
Sodium Ions
Calcium Ions
Potassium Ions
Magnesium Ions
Absorbency (Capacity)
Absorbency (Rate)
Surface resistivity
0.00002 mg/g (0.02 ppm)
0.00012 mg/g (0.12 ppm)
0.00012 mg/g (0.12 ppm)
0.00040 mg/g (0.40 ppm)
0.000135 mg/g (0.135 ppm)
0.000026 mg/g (0.026ppm)
0.00051 mg/g (0.51 ppm)
0.000016 mg/g (0.016 ppm)
6259BESD
9" x 9"
140 g/m
0.045mg/g (45ppm)
0.080 mg/g (80 ppm)
1 x 108 – 1 x 1010 ohm/sq
2
(+/- 5 g/m2)
6.5 million/m
None Detected
337 ml/m
0.8 seconds
2
2
The wipe tests were done using the recommended practices of the Institute of Environmental Science, Swabs
and Wipes Working Group.
NOTE:
This information is believed to be accurate. It is
intended for professional end users having the skills
to evaluate and use the data properly.
ITW CHEMTRONICS® does not guarantee the
accuracy of the data and assumes no liability in
connection with damages incurred while using it.
DISTRIBUTED BY:
TECHNICAL AND APPLICATION
ASSISTANCE
ITW Chemtronics provides a technical hotline to answer
your technical and application related questions.
The toll free number is:
Chemtronics is a registered trademark of ITW Chemtronics. All rights reserved. Coventry and Poly Onyx™ are trademarks of
ITW Chemtronics. All rights reserved.
1-800-TECH-401.
TECHNICAL HOT LINE 1-800-TECH-401
Loading...