Page 1
@ 70°F
@ 70°F /1 atm
Liquified Gas
Internal Pressure
5 years
RoHS/WEEE
TDS # 1054
CHEMTRONICS
Technical Data Sheet
Arctic Blast™ Freeze Spray
PRODUCT DESCRIPTION
Arctic B last™ F reeze S pray is specifically d esigned
for locating th ermal in termittent e lectrical
components a nd c ooling pr inted c ircuit boa rds.
Utilizing an u ltra-low g lobal w arming p otential
coolant, t his product offers t he best cooling possible
with th e lo west g lobal warming impact. Arctic
Blast™ F reeze S pray is nonf lammable, r esidue-free
and provides fast cooling action.
Cools surfaces to below -49°F / -45 °C
Ultra-low global warming impact of 6
Nonflammable
High heat transfer
Pinpoint spray for individual component isolation
Noncorrosive
Ultra-pure, filtered to <0.2 microns
Leaves no residue
Nonabrasive on most surfaces
CFC, HCFC and HFC free
VOC free
TYPICAL APPLICATIONS
Arctic Blast™ Freeze Spray can be used to:
Cool Equipment for Testing
Dissipate Heat While Soldering or
Desoldering
Isolate Thermal Intermittent Components
Test Circuit Traces for Continuity
Test Printed Circuit Boards for Stress
Fractures
Track Intermittent Failures and Shorts
COMPATIBILITY
Arctic B last™ F reeze S pray is g enerally c ompatible
with mo st ma terials u sed in printed circuit board
fabrication, i ncluding s ensitive pl astics and
compounds. W ith a ny circuit refrigerant,
compatibility must be de termined on a non -critical
area prior to use.
TYPICAL PRODUCT DATA AND PHYSICAL
PROPERTIES
Boiling Point -2 °F / -19 °C
Cools To:
Vapor Density (air=1)
Solubility in Water
Specific Gravity
(water = 1 @70°F)
Evaporation Rate >1
(butyl acetate=1)
Appearance Clear, Colorless
Odor
Flash Point (TCC)
Shelflife
Status
-49 °F / -45 °C
4.0
>0.10% by weight
1.17
Slight Ethereal
47 psia @ 70 °F
None
Page 2
Material
Compatibility
Buna-N
Good
Graphite
Excellent
HDPE
Fair
LDPE
Fair
Lexan
Good
Neoprene
Good
Cross-Linked PE
Good
Polyacrylate
Good
Polystyrene
Good
PVC
Good
Silicone Rubber
Fair
Teflon
Fair
Viton
Poor
CFC
0.0%
VOC
0.0%
HCFC
0.0%
HFC
0.0%
CL Solv.
0.0%
ODP
0.0
to e valuate a nd us e t he da ta pr operly.
USAGE INSTRUCTIONS
For industrial use only.
Read MSDS carefully prior to use.
No special surface preparation is required prior to
using Arctic Blast™ Freeze Spray. Direct spray onto
the area to instantly cool components, circuit boards
or adhesives. For optimum performance and pin
point control, use Arctic Blast™ Freeze Spray with
the attached extension tube.
AVAILABILITY
ES1054 10 oz. Aerosol
DISTRIBUTED BY:
TECHNICAL & APPLICATION
ASSISTANCE
Chemtronics provides a t echnical hot line t o an swer
your technical and application related questions. T he
toll free number is: 1-800-TECH-401.
ENVIRONMENTAL IMPACT DATA
ENVIRONMENTAL IMPACT DATA
CFC, H CFC, CL . S OLV., VOC, and H FC num bers
shown a re t he c ontent by w eight. O zone depletion
potential (ODP) is determined in accordance with the
Montreal Protocol and U .S. C lean A ir A ct of 1990.
The O DP of this product is 0.0. I t is the sum of the
ODP o f t he s ubstances that may contribute t o t he
depletion of s tratospheric oz one, ba sed upon t he
weight of each substance in the product’s formulation.
VOC consideration i s ba sed on the ma terials b eing
not photochemically reactive by C ommonly Used
Standards (material supplier).
NOTE:
This information is be lieved t o be a ccurate. I t i s
intended f or pr ofessional e nd us ers having t he s kills
CHEMTRONICS does not guarantee the accuracy of
the data and assumes no l iability i n c onnection with
damages incurred while using it.
Chemtronics® is a r egistered t rademark o f Chemtronics. All
rights reserved. Arctic Blast™ is a t rademark of Chemtronics.
All rights reserved.
All other t rademarks h erein ar e t rademarks o r r egistered
trademarks of their respective owners.
Loading...