Page 1
@ 77°F
@ 77°F /1 atm
Liquified Gas
CHEMTRONICS
Technical Data Sheet
Freez-It Antistat
TDS # 1051
PRODUCT DESCRIPTION
Freez-It Antistat is engineered for locating
thermal intermittent electrical components or
cooling pr inted c ircuit boa rds with minimal
static ge neration. T his c ircuit refrigerant
system is nonf lammable, r esidue-free a nd
provides fast cooling action.
Minimal static generation
Nonflammable
High heat transfer
Low static generation
Noncorrosive
Lowers temperature to -60°F (51°C)
Ultra pure, filtered to <0.2 microns
Leaves no residue
Nonabrasive on most surfaces
Dries fast
Contains no CFCs or HCFCs
TYPICAL APPLICATIONS
Freez-It
Cool Equipment for Testing
Dissipate Heat While Soldering or
Isolate Thermal Intermittent
Test Circuit Traces for Continuity
Test Printed Circuit Boards for Stress
Track Static Sensitive Components
Antistat can be used to:
Desoldering
Components
Fractures
TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES
Boiling Point -15.7°F
Vapor Density (air=1)
Solubility in Water
Specific Gravity
(water = 1 @77°F)
Evaporation Rate >1
(butyl acetate=1)
Appearance Clear, Colorless
Odor
Surface Tension
(dynes/cm @ 77°F)
Flash Point (TCC)
Shelflife 5 years
COMPATIBILITY
Freez-It
with m ost materials used in printed circuit
board f abrication, inc luding sensitive
plastics and compounds. W ith a ny c ircuit
refrigerant, c ompatibility m ust be
determined on a non-critical a rea pr ior to
use.
Antistat is ge nerally compatible
3.18
1.0% by weight
1.21
Slight Ethereal
7.8
None
Page 2
Material
Compatibility
Buna-N
Fair
Graphite
Good
HDPE
Good
LDPE
Good
Lexan
Poor
Neoprene
Good
Cross-Linked PE
Good
Polyacrylate
Poor
Polystyrene
Good
PVC
Good
Silicone Rubber
Fair
Teflon
Good
Viton
Poor
Freez-It Antistat
56% Less
40 v/in.
Static
Competitor’s
Antistat Freeze Spray
90 v/in.
0
20
40
60
80
100
120
Static Generation (V/IN.)
CFC
0.0%
VOC
0.9%
HCFC
0.0%
HFC
99.1%
CL Solv.
0.0%
ODP
0.0
Competitive Assessment of Freez-It Antistat
Chemtronics provides a t echnical hot line t o answer
your t echnical a nd a pplication related questions.
The toll free number is:
1-800-TECH-401.
ENVIRONMENTAL IMPACT DATA
ENVIRONMENTAL IMPACT DATA
CFC, HCFC, CL. SOLV., V OC, and H FC numbers
shown a re t he c ontent by w eight. Ozone de pletion
potential ( ODP) i s d etermined i n acco rdance w ith the
Montreal Protocol and U.S. Clean Air Act of 1990. T he
ODP of this product is 0.0. I t is the sum of the ODP of
the substances that m ay c ontribute t o t he de pletion of
stratospheric oz one, based upon t he w eight of each
substance in the product’s formulation.
NOTE:
This information is believed to be accurate. It is intended
for p rofessional en d u sers h aving t he sk ills t o evaluate
and use t he da ta pr operly. C HEMTRONICS does not
guarantee t he accu racy o f t he d ata an d assumes n o
liability in connection with damages incurred while using
it.
USAGE INSTRUCTIONS
For industrial use only.
Read MSDS carefully prior to use.
No special surface preparation is required
prior to using Freez-It
Antistat. Direct spray
onto the area to instantly cool components,
circuit boards or adhesives. For optimum
performance and pin point control, use
Freez-It
Antistat with the attached extension
tube.
AVAILABILITY
ES1051 10 oz. Aerosol
ES1551 15 oz. Aerosol
TECHNICAL & APPLICATION
ASSISTANCE
DISTRIBUTED BY:
Loading...