Chemetron Continuous, Pediatric Continuous, Low Vacuum Continuous, High Vacuum Continuous, Surgical Continuous User manual
...
Vacutron® Suction Regulators
& Accessories Guide
Vacutron® Suction Regulators by Chemetron
®
Chemetron has been a leader in suction regulators for
more than 40 years. The Vacutron line offers safety
and performance features unlike any other regulator on
the market.
Vacutron provides four distinct advantages over other suction regulators.
Superior Patient Safety
Vacutron suction regulators have a secondary internal vacuum relief valve.
This valve ensures that under no circumstance, i.e. component failure, can the
vacuum pressure delivered to the patient exceed a pre-set safe level so the patient
is not inadvertently exposed to the full line vacuum pressure.
Simple and Inexpensive Sterilization
In the unlikely event the Vacutron becomes contaminated with aspirated material,
the regulator can be sterilized by flushing it with common isopropyl alcohol.
Model-Specific Labeling
Each Vacutron suction regulator has a color-coded label on the front of the product
to enable the clinician to quickly and easily identify which type of regulator is
connected.
Standard Glow-in-the-Dark Gauge
Allied’s Vacutron suction regulator comes standard with a glow-in-the-dark gauge
and needle.
Table of Contents
Vacutron® Suction Regulators by Chemetron® . . . . . . . . . . .
Continuous Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pediatric Continuous Model . . . . . . . . . . . . . . . . . . . . . . . . .
Low Vacuum (Neonatal) Continuous Model . . . . . . . . . . . . .
High Vacuum Continuous Model . . . . . . . . . . . . . . . . . . . . .
Surgical Continuous Model . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous/Intermittent Model . . . . . . . . . . . . . . . . . . . . . . .
Pediatric Continuous/Intermittent Model . . . . . . . . . . . . . . .
Intermittent Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disposable Collection Canisters . . . . . . . . . . . . . . . . . . . . . . .
Disposable Collection Canister Accessories . . . . . . . . . . . . . .
Reusable Collection Bottle Assemblies & Accessories . . . . . .
Suction Regulator Accessories . . . . . . . . . . . . . . . . . . . . . . . .
Vacutron Configuration Table . . . . . . . . . . . . . . . . . . . . . . . .
1
2
3
4
5
6
7
8
9
10
11
12
13
13
Vacutron® Suction Regulators by Chemetron
®
High-impact polycarbonate
case for strength and
durability.
Oversized vacuum regulating
knob ensures precise vacuum
control.
Model-specific color-coded label
for quick and easy model
identification.
Easy access mode selection knob
gives instant access to regulated,
intermittent and full-line modes,
depending on the model.
Color-coded glow-in-the-dark
analog gauge provides easy
readability under typical hospital
lighting conditions.
Weight-bearing brass posts prevent
case from cracking. A full line of
inlet and outlet fittings ensures
compatibility with existing fixtures
in any medical facility.
Outlet to the patient
Inlet to
the wall
Chemetron®
Male Adapter
Female Adapter
Oxequip® Med*Star™
1/8" NPT
Outlet to the Patient Fittings
DISS Male
Fitting
Inlet to the Wall Fittings
Ohmeda®
Male Adapter
Female Adapter
Metal Barbed
Stem Fitting
Male Adapter
DISS
45° DISS
Male Fitting
Puritan Bennett™
Male Adapter
DISS
Handtight Adapter
Bacteria Filter/
Barbed Stem
1
Continuous Model
Specifications
Operating Modes: OFF and Regulated
Regulated Vacuum Range: 0-300 mm Hg
Safety Relief Valves: 1 @ 320 mm Hg
Vacuum Gauge Scale: 0-300 mm Hg in 5 mm Hg increments
0-40 kPa in 2 kPa increments
Dimensions: 6.8" H x 2.65" W x 4.07" D (174 mm x 67 mm x 104 mm)
Weight: 1.3 lbs. (0.59 kg)
Warranty: 10 years
The continuous suction regulator is designed to deliver constant
vacuum for general suction procedures, including routine
maintenance of the patient airway, oropharyngeal and endotracheal
suctioning.
Key Features
Internal safety relief valve limits the maximum vacuum level to
320 mm Hg in the event of regulator failure or inaccuracy
Superior regulation mechanism ensures stable vacuum settings
even with fluctuations in source vacuum
ISO configurations available
22-23-0000
22-23-0100
22-23-0116
22-23-0200
22-23-1114
Continuous Suction Regulator Configurator
Using the diagram below, one can configure any continuous suction regulator.
For example, the part number for a continuous Vacutron with U.S. coloring, a DISS male patient
fitting and an Ohmeda male wall fitting is 22-13-1106.
The complete Vacutron Configuration Table is on page 13.
22-X3-XXXX
Color Code
1: United States
2: ISO
Outlet to the Patient Fitting
11: DISS Male
12: Metal Barbed Stem
14: 45° DISS Male
15: Bacteria Filter to Barbed Stem
2
Inlet to the Wall Fitting
00: 1/8" NPT Female
04: Med*Star Male
05: Puritan Bennett Male
06: Ohmeda Male
07: DISS Female
08: Chemetron Male
11: DISS Handtight
Pediatric Continuous Model
The pediatric continuous suction regulator is designed to deliver
constant vacuum for general suction procedures on pediatric patients,
including routine maintenance of the airway, oropharyngeal and
endotracheal suctioning.
Key Features
Internal safety relief valve limits the maximum vacuum level to
140 mm Hg in the event of regulator failure or inaccuracy
Superior regulation mechanism ensures stable vacuum settings
even with fluctuations in source vacuum
ISO configurations available
Specifications
Operating Modes: OFF and Regulated
Regulated Vacuum Range: 0-130 mm Hg
Safety Relief Valves: 1 @ 140 mm Hg
Vacuum Gauge Scale: 0-150 mm Hg in 5 mm Hg increments
0-20 kPa in 1 kPa increments
Dimensions: 6.8" H x 2.65" W x 4.07" D (174 mm x 67 mm x 104 mm)
Weight: 1.3 lbs. (0.59 kg)
Warranty: 10 years
22-28-0100
22-28-0200
22-28-0214
Pediatric Continuous Suction Regulator Configurator
Using the diagram below, one can configure any pediatric continuous suction regulator.
For example, the part number for a pediatric continuous Vacutron with U.S. coloring, a DISS male
patient fitting and an Ohmeda male wall fitting is 22-18-1106.
The complete Vacutron Configuration Table is on page 13.
22-X8-XXXX
Color Code
1: United States
2: ISO
Outlet to the Patient Fittings
11: DISS Male
12: Metal Barbed Stem
14: 45° DISS Male
15: Bacteria Filter to Barbed Stem
3
Inlet to the Wall Fittings
00: 1/8" NPT Female
04: Med*Star Male
05: Puritan Bennett Male
06: Ohmeda Male
07: DISS Female
08: Chemetron Male
11: DISS Handtight
Low Vacuum (Neonatal) Continuous Model
The low vacuum continuous suction regulator is designed to deliver
constant vacuum for general suction procedures on neonatal patients,
including routine maintenance of the airway, oropharyngeal and
endotracheal suctioning.
Key Features
Internal safety relief valve limits the maximum vacuum level to
100 mm Hg in the event of regulator failure or inaccuracy
Superior regulation mechanism ensures stable vacuum settings
even with fluctuations in source vacuum
ISO configurations available
Specifications
Operating Modes: OFF and Regulated
Regulated Vacuum Range: 0-90 mm Hg
Safety Relief Valves: 1 @ 100 mm Hg
Vacuum Gauge Scale: 0-100 mm Hg in 5 mm Hg increments
0-13 kPa in 1 kPa increments
Dimensions: 6.8" H x 2.65" W x 4.07" D (174 mm x 67 mm x 104 mm)
Weight: 1.3 lbs. (0.59 kg)
Warranty: 10 years
22-29-0050
22-29-0202
22-29-0214
Low Vacuum Continuous Suction Regulator Configurator
Using the diagram below, one can configure any low vacuum continuous suction regulator.
For example, the part number for a low vacuum continuous Vacutron with U.S. coloring, a DISS
male patient fitting and an Ohmeda male wall fitting is 22-19-1106.
The complete Vacutron Configuration Table is on page 13.
22-X9-XXXX
Color Code
1: United States
2: ISO
Outlet to the Patient Fittings
11: DISS Male
12: Metal Barbed Stem
14: 45° DISS Male
15: Bacteria Filter to Barbed Stem
4
Inlet to the Wall Fittings
00: 1/8" NPT Female
04: Med*Star Male
05: Puritan Bennett Male
06: Ohmeda Male
07: DISS Female
08: Chemetron Male
11: DISS Handtight
High Vacuum Continuous Model
The high vacuum suction regulator is designed for procedures that
require constant vacuum pressures in excess of 300 mm Hg.
There are two operational modes: regulated suction and full line.
Regulated suction allows the clinician to set the vacuum level
between 0 and the vacuum line pressure. On full line mode, the
vacuum pressure delivered is unregulated and equal to the vacuum
line pressure.
Key Features
Superior regulation mechanism ensures stable vacuum settings
even with fluctuations in source vacuum
ISO configurations available
Specifications
Operating Modes: OFF, Regulated and Full Line
Regulated Vacuum Range: 0-760 mm Hg
Safety Relief Valves: N/A
Vacuum Gauge Scale: 0-760 mm Hg in 20 mm Hg increments
0-100 kPa in 5 kPa increments
Dimensions: 6.8" H x 2.65" W x 4.07" D (174 mm x 67 mm x 104 mm)
Weight: 1.3 lbs. (0.59 kg)
Warranty: 10 years
22-24-0000
22-24-0050
22-24-0100
22-24-0116
22-24-0200
22-24-0500
22-24-1114
22-24-1508
High Vacuum Continuous Suction Regulator Configurator
Using the diagram below, one can configure any high vacuum continuous suction regulator.
For example, the part number for a high vacuum continuous Vacutron with U.S. coloring, a DISS
male patient fitting and an Ohmeda male wall fitting is be 22-14-1106.
The complete Vacutron Configuration Table is on page 13.
22-X4-XXXX
Color Code
1: United States
2: ISO
Outlet to the Patient Fittings
11: DISS Male
12: Metal Barbed Stem
14: 45° DISS Male
15: Bacteria Filter to Barbed Stem
5
Inlet to the Wall Fittings
00: 1/8" NPT Female
04: Med*Star Male
05: Puritan Bennett Male
06: Ohmeda Male
07: DISS Female
08: Chemetron Male
11: DISS Handtight
Surgical Continuous Model
The surgical suction regulator is designed for use in surgical suites.
There are two operational modes: regulated vacuum and full line.
Regulated suction allows the clinician to set the vacuum level
between 0 and 300 mm Hg. On full line mode, the vacuum pressure
delivered is unregulated and equal to the vacuum line pressure.
Key Features
Internal safety relief valve limits the maximum vacuum level on
regulated mode to 320 mm Hg in the event of regulator failure
or inaccuracy
Superior regulation mechanism ensures stable vacuum settings
even with fluctuations in source vacuum
ISO configurations available
Specifications
Operating Modes: OFF, Regulated and Full Line
Regulated Vacuum Range: 0-300 mm Hg
Safety Relief Valves: 1 @ 320 mm Hg
Vacuum Gauge Scale: 0-300 mm Hg in 5 mm Hg increments
0-40 kPa in 2 kPa increments
Dimensions: 6.8" H x 2.65" W x 4.07" D (174 mm x 67 mm x 104 mm)
Weight: 1.3 lbs. (0.59 kg)
Warranty: 10 years
22-22-0000
22-22-0100
22-22-0214
Surgical Continuous Suction Regulator Configurator
Using the diagram below, one can configure any surgical continuous suction regulator.
For example, the part number for a surgical continuous Vacutron with U.S. coloring, a DISS male
patient fitting and an Ohmeda male wall fitting is 22-12-1106.
The complete Vacutron Configuration Table is on page 13.
22-X2-XXXX
Color Code
1: United States
2: ISO
Outlet to the Patient Fittings
11: DISS Male
12: Metal Barbed Stem
14: 45° DISS Male
15: Bacteria Filter to Barbed Stem
6
Inlet to the Wall Fittings
00: 1/8"NPT Female
04: Med*Star Male
05: Puritan Bennett Male
06: Ohmeda Male
07: DISS Female
08: Chemetron Male
11: DISS Handtight
Continuous/Intermittent Model
The continuous/Intermittent suction regulator is designed to
support a variety of procedures requiring constant or intermittent
suction. Constant suction is used primarily to maintain a patient’s
airway, while intermittent suction is used for drainage procedures.
Key Features
Dual safety relief valves limit the maximum vacuum level on
both constant and intermittent modes in the event of regulator
failure or inaccuracy
Superior regulation mechanism ensures stable vacuum settings
even with fluctuations in source vacuum
ISO configurations available
Specifications
Operating Modes: OFF, Regulated and Intermittent
Regulated Vacuum Range: 0-300 mm Hg (Regulated)
0-150 mm Hg (Intermittent)
Cycle Times: 17 seconds of suction followed by 10 seconds without suction
Safety Relief Valves: 1 @ 320 mm Hg (Regulated)
1 @ 170 mm Hg (Intermittent)
Vacuum Gauge Scale: 0-300 mm Hg in 5 mm Hg increments
0-40 kPa in 2 kPa increments
Dimensions: 6.8" H x 2.65" W x 4.07" D (174 mm x 67 mm x 104 mm)
Weight: 1.3 lbs. (0.59 kg)
Warranty: 10 years
22-25-1050
22-25-1050-SPAN
22-25-1100
22-25-1114
22-25-1200
Continuous/Intermittent Suction Regulator Configurator
Using the diagram below, one can configure any continuous/intermittent suction regulator.
For example, the part number for a continuous/intermittent Vacutron with U.S. coloring, a DISS
male patient fitting and an Ohmeda male wall fitting is 22-15-1106.
The complete Vacutron Configuration Table is on page 13.
22-X5-XXXX
Color Code
1: United States
2: ISO
Outlet to the Patient Fittings
11: DISS Male
12: Metal Barbed Stem
14: 45° DISS Male
15: Bacteria Filter to Barbed Stem
7
Inlet to the Wall Fittings
00: 1/8" NPT Female
04: Med*Star Male
05: Puritan Bennett Male
06: Ohmeda Male
07: DISS Female
08: Chemetron Male
11: DISS Handtight
Pediatric Continuous/Intermittent Model
The pediatric continuous/intermittent suction regulator is designed
to support a variety of procedures requiring constant or intermittent
suction on pediatric patients. Constant suction is used primarily to
maintain the patient airway, while intermittent suction is used for
drainage procedures.
Key Features
Dual safety relief valves limit the maximum vacuum level on
both constant and intermittent modes in the event of regulator
failure or inaccuracy
Superior regulation mechanism ensures stable vacuum settings
even with fluctuations in source vacuum
ISO configurations available
Specifications
Operating Modes: OFF, Regulated and Intermittent
Regulated Vacuum Range: 0-130 mm Hg (Regulated)
0-110 mm Hg (Intermittent)
Cycle Times: 17 seconds of suction followed by 10 seconds without suction
Safety Relief Valves: 1 @ 140 mm Hg (Regulated)
1 @ 120 mm Hg (Intermittent)
Vacuum Gauge Scale: 0-150 mm Hg in 5 mm Hg increments
Dimensions: 6.8" H x 2.65" W x 4.07" D (174 mm x 67 mm x 104 mm)
Weight: 1.3 lbs. (0.59 kg)
Warranty: 10 years
22-27-0214
22-27-1100
22-27-1200
Pediatric Continuous/Intermittent Suction Regulator Configurator
Using the diagram below, one can configure any pediatric continuous/intermittent suction regulator.
For example, the part number for a pediatric continuous/intermittent Vacutron with U.S. coloring,
a DISS male patient fitting and an Ohmeda male wall fitting is 22-17-1106.
The complete Vacutron Configuration Table is on page 13.
22-X7-XXXX
Color Code
1: United States
2: ISO
Outlet to the Patient Fittings
11: DISS Male
12: Metal Barbed Stem
14: 45° DISS Male
15: Bacteria Filter to Barbed Stem
8
Inlet to the Wall Fittings
00: 1/8" NPT Female
04: Med*Star Male
05: Puritan Bennett Male
06: Ohmeda Male
07: DISS Female
08: Chemetron Male
11: DISS Handtight
Intermittent Model
Specifications
Operating Modes: OFF and Intermittent
Regulated Vacuum Range: 0-150 mm Hg
Cycle Times: 17 seconds of suction followed by 10 seconds without suction
Safety Relief Valves: 1 @ 170 mm Hg
Vacuum Gauge Scale: 0-300 mm Hg in 5 mm Hg increments
0-40 kPa in 2 kPa increments
Dimensions: 6.8" H x 2.65" W x 4.07" D (174 mm x 67 mm x 104 mm)
Weight: 1.3 lbs. (0.59 kg)
Warranty: 10 years
Intermittent suction regulators are designed to deliver intermittent
vacuum only. This regulator is used when clinicians want to ensure
that constant suction is never delivered.
Key Features
Internal safety relief valve limits the maximum vacuum level to
170 mm Hg in the event of regulator failure or inaccuracy
Superior regulation mechanism ensures stable vacuum settings
even with fluctuations in source vacuum
ISO configurations available
22-26-0214
22-26-1100
22-26-1200
Intermittent Suction Regulator Configurator
Using the diagram below, one can configure any intermittent suction regulator.
For example, the part number for an intermittent Vacutron with US coloring, a DISS male patient
fitting and an Ohmeda male wall fitting is 22-16-1106.
The complete Vacutron Configuration Table is on page 13.
22-X6-XXXX
Color Code
1: United States
2: ISO
Outlet to the Patient Fittings
11: DISS Male
12: Metal Barbed Stem
14: 45° DISS Male
15: Bacteria Filter to Barbed Stem
9
Inlet to the Wall Fittings
00: 1/8" NPT Female
04: Med*Star Male
05: Puritan Bennett Male
06: Ohmeda Male
07: DISS Female
08: Chemetron Male
11: DISS Handtight
Disposable Collection Canisters (DCUs)
Unique DISS connection
attaches directly to most wall
suction regulators, saving time
and eliminating wall brackets.
Key Features
Unique filter and self-sealing material located in the lid improve flow up to 20%, enhancing
performance over mechanical float systems
When the filter comes into contact with moisture, it immediately stops flow from the patient
and prevents fluids from entering the suction regulator
Unique DISS connection option allows canisters to be attached directly to most wall suction
regulators in the OR, ER, ICU and CCU
Accurate, easy to read calibrations and an enlarged area in which to write patient information
Snap-on lid is easy to attach to the canister and virtually impossible to remove
Audible “snap” gives clear confirmation that the lid is properly sealed and secure
Tubing hooks built into the lid eliminate the need to coil up excess tubing, preventing kinks
and occlusions
Caps for all ports are attached to the lid for convenience in sealing the canister after use
20-08-0001
20-08-0002
20-08-0003
20-08-0004
20-08-0005
20-08-0006
20-08-0007
20-08-0008
Disposable Collection Canister, DISS inlet & hydrophobic filter, 2400 ml (36/case)
Disposable Collection Canister, stem inlet & hydrophobic filter, 2400 ml (36/case)
Disposable Collection Canister, stem inlet & hydrophobic filter, 1500 ml (48/case)
Disposable Collection Canister, DISS inlet & hydrophobic filter, 1500 ml (48/case)
Disposable Collection Canister, DISS inlet & hydrophobic filter, with tubing, 2400 ml (36/case)*
Disposable Collection Canister, stem inlet & hydrophobic filter, with tubing, 2400 ml (36/case)**
Disposable Collection Canister, stem inlet & hydrophobic filter, with tubing, 1500 ml (42/case)**
Disposable Collection Canister, DISS inlet & hydrophobic filter, with tubing, 1500 ml (42/case)*
*PVC tubing, 72", 1/4" ID
**PVC tubing, 18" and 72", 1/4" ID
10
Disposable Collection Canister Accessories
20-02-0152 20-02-0151 20-02-0150
Critical Measurement Insert
For precise volume determination
of aspirated material. Inserts into
a 1500 ml or 2400 ml canister.
Collection Canister Stand with Vacuum
Manifold
Unlike traditional collection canister stands,
the Allied stand has an integrated vacuum
manifold. At the top of the stand, the suction
regulator connects to the manifold via a DISS
male connection. From here, the manifold
system directs the vacuum to two 5/16" hose
barb outlets. The outlets feature shut-off
valves which enable the outlets to be used
individually or in tandem. Completing the
canister stand are four permanently affixed
slide brackets, four canister holders and
casters for enhanced mobility.
Specimen Bag
Filters large particles from aspirate.
Fits into canister accessory port for
easy accessibility.
Canister Holder
Holds collection canister by
inserting the holder into a slide
bracket on a canister carrier pole.
20-02-0023
Canister Stand Expansion Kit
Attaches to collection canister pole to
convert a standard 4-canister carrier into
an 8-canister carrier. Kit includes 4 slide
brackets, 4 canister holders, and 2 screws.
20-02-0023
20-02-0030
20-02-0028
20-02-0150
20-02-0151
20-02-0152
Collection Canister Carrier, 4-canister model, 36" high
Collection Canister Carrier, 4-canister model, 21" high
Canister Carrier Expansion Kit
Canister Holder, 12/case
Specimen Bag, 4.5", 12/case
Critical Measurement Insert, 12/case
11
Reusable Collection Bottle Assemblies & Accessories
Allied collection bottle assemblies are used for the collection of
aspirated material. They are available in polycarbonate or glass
and incorporate a positive shut-off cap and float assembly that
interrupts suction to help prevent fluid carryover into the
regulator or central vacuum system.
Key Features
Offered in four sizes: 2800 ml, 1200 ml, 600 ml and 473 ml
Bottles are available in glass and polycarbonate, which can
be autoclaved
Collection bottles can be purchased complete (bottle with
cap and float) or by the case (bottle only)
Cap and float assembly is autoclavable and can be pur-
22-10-4003 22-10-0002 22-10-0004 22-10-4010
Bottle Holders & Suction Bottle Carrier
chased separately
22-11-0004 22-11-0007 22-11-0006
Ordering Information
22-93-0002
22-10-0002
22-93-0003
22-10-0004
22-93-0020
22-10-0010
22-93-5001
22-10-4003
22-93-5002
22-10-4002
22-93-5010
22-10-4010
22-10-0008
22-11-0004
22-11-0006
22-11-0007
22-11-0024
1200 ml Glass Bottle (bottle only), 6/case
1200 ml Glass Bottle & lid assembly
600 ml Glass Bottle (bottle only), 12/case
600 ml Glass Bottle & lid assembly
473 ml Glass Bottle (bottle only), 12/case
473 ml Glass Bottle & lid assembly
2800 ml Polycarbonate Bottle (bottle only), 6/case
2800 ml Polycarbonate Bottle & lid assembly
1200 ml Polycarbonate Bottle (bottle only), 6/case
1200 ml Polycarbonate Bottle & lid assembly
473 ml Polycarbonate Bottle (bottle only), 12/case
473 ml Polycarbonate Bottle & lid assembly
Cap & Float Assembly
Bottle Holder without lock
Bottle Holder Bracket
Bottle Holder with lock
Suction Bottle Carrier, for one-gallon collection bottles, with 4 conductive swivel casters
22-11-0024
12
Suction Regulator Accessories
Disposable Hydrophobic Bacteria Filter
Designed to help protect the vacuum system from
contamination due to aerosols or collection bottle overflow
Hydrophobic microporous membrane filters air while
helping block the flow of aqueous fluids and aerosol
contaminants
Filter efficiency 99.97% D.O.P. retention
(.3 micron particle size)
Ordering Information
01-90-3100
01-90-3100
01-90-3928
Disposable Hydrophobic Bacteria Filter, 1/8" NPT x 1/4" hose barb, 3/pkg.
Disposable Hydrophobic Bacteria Filter, 1/4" hose barb x 1/4" hose barb, 3/pkg.
Vacutron® Configuration Table
Vacutron Mod-
el
Continuous
Surgical
High
Vacuum
Pediatric
Continuous
Low
Vacuum
Continuous/
Intermittent
Pediatric
Continuous/
Intermittent
Intermittent
Outlet to the
Patient Fitting
DISS Male 22-13-1108 22-13-1104 22-13-1106 22-13-1105 22-13-1100 22-13-1107 22-13-1111
Metal Barbed Stem 22-13-1208 22-13-1204 22-13-1206 22-13-1205 22-13-1200 22-13-1207 22-13-1211
45° DISS Male 22-13-1408 22-13-1404 22-13-1406 22-13-1405 22-13-1400 22-13-1407 22-13-1411
Bacteria Filter to Barb Stem 22-13-1508 22-13-1504 22-13-1506 22-13-1505 22-13-1500 22-13-1507 22-13-1511
DISS Male 22-12-1108 22-12-1104 22-12-1106 22-12-1105 22-12-1100 22-12-1107 22-12-1111
Metal Barbed Stem 22-12-1208 22-12-1204 22-12-1206 22-12-1205 22-12-1200 22-12-1207 22-12-1211
45° DISS Male 22-12-1408 22-12-1404 22-12-1406 22-12-1405 22-12-1400 22-12-1407 22-12-1411
Bacteria Filter to Barb Stem 22-12-1508 22-12-1504 22-12-1506 22-12-1505 22-12-1500 22-12-1507 22-12-1511
DISS Male 22-14-1108 22-14-1104 22-14-1106 22-14-1105 22-14-1100 22-14-1107 22-14-1111
Metal Barbed Stem 22-14-1208 22-14-1204 22-14-1206 22-14-1205 22-14-1200 22-14-1207 22-14-1211
45° DISS Male 22-14-1408 22-14-1404 22-14-1406 22-14-1405 22-14-1400 22-14-1407 22-14-1411
Bacteria Filter to Barb Stem 22-14-1508 22-14-1504 22-14-1506 22-14-1505 22-14-1500 22-14-1507 22-14-1511
DISS Male 22-18-1108 22-18-1104 22-18-1106 22-18-1105 22-18-1100 22-18-1107 22-18-1111
Metal Barbed Stem 22-18-1208 22-18-1204 22-18-1206 22-18-1205 22-18-1200 22-18-1207 22-18-1211
45° DISS Male 22-18-1408 22-18-1404 22-18-1406 22-18-1405 22-18-1400 22-18-1407 22-18-1411
Bacteria Filter to Barb Stem 22-18-1508 22-18-1504 22-18-1506 22-18-1505 22-18-1500 22-18-1507 22-18-1511
DISS Male 22-19-1108 22-19-1104 22-19-1106 22-19-1105 22-19-1100 22-19-1107 22-19-1111
Metal Barbed Stem 22-19-1208 22-19-1204 22-19-1206 22-19-1205 22-19-1200 22-19-1207 22-19-1211
45° DISS Male 22-19-1408 22-19-1404 22-19-1406 22-19-1405 22-19-1400 22-19-1407 22-19-1411
Bacteria Filter to Barb Stem 22-19-1508 22-19-1504 22-19-1506 22-19-1505 22-19-1500 22-19-1507 22-19-1511
DISS Male 22-15-1108 22-15-1104 22-15-1106 22-15-1105 22-15-1100 22-15-1107 22-15-1111
Metal Barbed Stem 22-15-1208 22-15-1204 22-15-1206 22-15-1205 22-15-1200 22-15-1207 22-15-1211
45° DISS Male 22-15-1408 22-15-1404 22-15-1406 22-15-1405 22-15-1400 22-15-1407 22-15-1411
Bacteria Filter to Barb Stem 22-15-1508 22-15-1504 22-15-1506 22-15-1505 22-15-1500 22-15-1507 22-15-1511
DISS Male 22-17-1108 22-17-1104 22-17-1106 22-17-1105 22-17-1100 22-17-1107 22-17-1111
Metal Barbed Stem 22-17-1208 22-17-1204 22-17-1206 22-17-1205 22-17-1200 22-17-1207 22-17-1211
45° DISS Male 22-17-1408 22-17-1404 22-17-1406 22-17-1405 22-17-1400 22-17-1407 22-17-1411
Bacteria Filter to Barb Stem 22-17-1508 22-17-1504 22-17-1506 22-17-1505 22-17-1500 22-17-1507 22-17-1511
DISS Male 22-16-1108 22-16-1104 22-16-1106 22-16-1105 22-16-1100 22-16-1107 22-16-1111
Metal Barbed Stem 22-16-1208 22-16-1204 22-16-1206 22-16-1205 22-16-1200 22-16-1207 22-16-1211
45° DISS Male 22-16-1408 22-16-1404 22-16-1406 22-16-1405 22-16-1400 22-16-1407 22-16-1411
Bacteria Filter to Barb Stem 22-16-1508 22-16-1504 22-16-1506 22-16-1505 22-16-1500 22-16-1507 22-16-1511
Chemetron
Oxequip
Med*Star
Inlet to the Wall Fittings
Ohmeda
Puritan
Bennett
1/8" NPT
Female
DISS
Female
DISS
Handtight
13
More Allied Innovations
Allied really does have it all under one roof. We have shown you our Vacutron® line of suction
regulators … but that’s just a part of the complete offering of products and repair parts for
home health care, long term care, medical centers and hospitals:
• Flowmeters
• CO2 Absorbents
• Oxygen Pressure Regulators
• Portable Aspirators
• Portable High Volume Air Compressors
Contact your Allied Healthcare Products sales representative or call 800-444-3940 to speak
with our expert Customer Service staff for complete information.
Litholyme
Timeter® Oxygen
Flowmeter
Gomco
AC/DC Portable Aspirator
®
CO2 Absorbent
®
OptiVac
®
B&F Oxygen Pressure Regulators
Timeter® PCS 414
High Volume Air Compressor
EMERGO EUROPE
EC REP
Prinsessegracht 20
2514 AP The Hague
The Netherlands
ISO 13485: 2003
Allied Healthcare Products, Inc. ▪ 1720 Sublette Avenue ▪ St. Louis, MO 63110 USA
314/771-2400 ▪ 800/444-3954 ▪ FAX: 314/771-0650 ▪ www.alliedhpi.com
U.S.
Toll Free: 800/444-3940
FAX: 800/477-7701
©Allied Healthcare Products, Inc.®
Canada & Mexico
Toll Free: 800/446-0552
FAX: 800/246-6201
All specifications are nominal and
subject to change without notice.
International
Telephone: 314/268-1683
FAX: 314/771-5183
Form 22-00-0007
Rev. May 2017
Loading...