Checkline MTG User Manual

– 1 –

TABLE OF CONTENTS

1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 02

2.0 Unpacking and Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03

3.0 Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04

4.0 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .004

5.0 Using Indicator Function Keys . . . . . . . . . . . . . . . . . . . . . . . .005

6.0 Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .007

6.1 Checking Thick Materials

6.2 Data Port

7.0 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09

8.0 Specifications and Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 11

9.0 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

– 12 –

9.0 WARRANTY

The manufacturer warrants to the original purchaser that this product
is of merchantable quality and confirms in kind and quality with the
descriptions and specifications thereof. Product failure or malfunction
arising out of any defect in workmanship or material in the product
existing at the time of delivery thereof which manifests itself within
one year from the sale of such product, shall be remedied by repair
or replacement of such product, at the manufacturer’s option, except
where unauthorized repair, disassembly, tampering, abuse or
misapplication has taken place, as determined by the manufacturer.
All returns for warranty or non-warranty repairs and/or replacement
must be authorized by the manufacturer, in advance, with all
repacking and shipping expenses to the address below to be borne by
the purchaser.

THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT
NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY AND
FITNESS FOR ANY PARTICULAR PURPOSE OR APPLICATION.
ELECTROMATIC SHALL NOT BE RESPONSIBLE NOR LIABLE
FOR ANY CONSEQUENTIAL DAMAGE, OF ANY KIND OR
NATURE, RESULTING FROM THE USE OF SUPPLIED
EQUIPMENT, WHETHER SUCH DAMAGE OCCURS OR IS
DISCOVERED BEFORE, UPON OR AFTER REPLACEMENT OR
REPAIR, AND WHETHER OR NOT SUCH DAMAGE IS CAUSED
BY MANUFACTURER’S OR SUPPLIER’S NEGLIGENCE WITHIN
ONE YEAR FROM INVOICE DATE.

Some State jurisdictions or States do not allow the exclusion or
limitation of incidental or consequential damages, so the above
limitation may not apply to you. The duration of any implied warranty,
including, without limitation, fitness for any particular purpose and
merchantability with respect to this product, is limited to the duration
of the foregoing warranty. Some states do not allow limitations on how
long an implied warranty lasts but, not withstanding, this warranty, in
the absence of such limitations, shall extend for one year from the date
of invoice.

Every precaution has been taken in the preparation of this manual. The manufacturer,
assumes no responsibility for errors or omissions. Neither is any liability assumed for
damages resulting from the use of information contained herein. Any brand or product
names mentioned herein are used for identification purposes only, and are trademarks or
registered trademarks of their respective holders.

– 2 –

1.0 INTRODUCTION

The Model MTG benchtop contact thickness gauge accurately and
conveniently performs geometric dimensional testing (thickness
measurement) on rubber, fabrics, foams, tapes/films and a wide
assortment of other soft materials. It employs a specified presser foot
(feeler) of a specific diameter/area, combined with a predetermined
mass (weight) as noted in the ASTM D 3767 standard.

The MTG system is supplied with a unique air damping feature
which ensures that the presser foot descends at the same rate for each
test. This eliminates human error resulting in superior repeatability.
If required, the rate of descent can be user-adjusted.

For those requiring data output for recording and quality
documentation purposes, a serial output cable and Windows-based
software program is optionally available.

8.0 S

PECIFICATIONS AND DIMENSIONS

Certified Electronic Indicator

Range

0–1"

(0–25mm

)

Resolution

.0001"

(0.001mm)

Power

CR 2450 Lithium batteries (2)

Units Inch or metric

Operator selectable

Data Output RS-232, Mitutoyo (MTI) , BCD

Certified Granite Base 6" x 6" x 2"

(152.4 x 152.4 x 50.8mm

)

Grade AA

Presser Foot 0.63"

(16mm)

Mass (Weight) 6.82 oz

(212 g)

Lifting Lever left hand

Maximum Height 5 inches

Warranty 1 year

– 11 –

– 3 –

2.0 U

NPACKING AND SET-UP

Your MTG system is packaged completely assembled and tested at our
plant to ensure a quality product. However, there are some basic steps
that must be performed before using your MTG for the first time.

1. Carefully unpack the MTG. Take special care when lifting to
support the unit from the granite base when unpacking and
whenever moving the unit.

2. If additional presser feet and weights (mass) have been ordered be
sure to also unpack those items, which are wrapped separately.

3. After the unit is unpacked, it can be cleaned with alcohol,

WITH EXCEPTION OF THE ELECTRONIC INDICATOR.

4. The MTG should then be placed on a clean, flat vibration-free
surface for use.

3.0 I

NSTALLING BATTERIES

1. Using a narrow edge, flathead
screwdriver, gently pry under
the tab on the left side of the
indicator bezel and slide out
the battery tray as you turn
the indicator face down.

2. Insert two CR 2450 Lithium
batteries (3V) into the tray
cavities, positive (+) side up.
Now slide the tray back into its
slot, taking care that the batteries
stay in proper position.

– 10 –

Presser Foot “A” Dim. (mm)

PF-1 10.0

PF-2 8.0

PF-3 6.3

PF-4 6.0

PF-5 5.0

PF-6 4.0

PF-7 3.2

PF-8 16.0

PF-9 25.0

Optional Presser Foot

(Feeler / Anvil)