User Manual
TABLE OF CONTENTS
1. Before You Begin .............................................................................. 3
What Is Included ............................................................................................... 3
Unpacking Instructions ...................................................................................... 3
Claims ........................................................................................................................ 3
Conventions ...................................................................................................... 3
Symbols ............................................................................................................ 3
Document Information ....................................................................................... 3
Product at a Glance .......................................................................................... 4
Safety Notes ...................................................................................................... 4
2. Introduction ....................................................................................... 5
Product Overview .............................................................................................. 5
Product Dimensions .......................................................................................... 5
3. Setup .................................................................................................. 6
AC Power .......................................................................................................... 6
Fuse Replacement (Power Linking) ........................................................................... 6
Fuse Replacement (Power In).................................................................................... 7
Power Linking............................................................................................................. 8
Mounting ........................................................................................................... 9
Orientation ................................................................................................................. 9
Rigging ....................................................................................................................... 9
4. Operation ..........................................................................................10
Control Panel Operation.................................................................................. 10
Menu Map ....................................................................................................... 10
Configuration (DMX) ....................................................................................... 10
DMX Personalities and Starting Address ................................................................ 10
DMX Channel Assignments and Values ......................................................... 11
15-CH ....................................................................................................................... 11
3-CH ......................................................................................................................... 11
Configuration (Standalone) ............................................................................. 12
Sound-Active Mode .................................................................................................. 12
Automatic Mode ....................................................................................................... 12
Master/Slave Mode .................................................................................................. 12
Footswitch Operation ............................................................................................... 13
Disconnecting the Footswitch .................................................................................. 13
5. Technical Information ......................................................................14
Product Maintenance ...................................................................................... 14
6. Technical Specifications ..................................................................15
Returns ............................................................................................................ 16
Contact Us ...................................................................................................... 16
Page 2 of 16 4BAR™ Flex User Manual (Rev. 7)
What Is
Unpacking
Instructions
included accessories) appear damaged from
Failure to do so in a timely manner may invalidate your claim with the
For other issues such as missing components or parts, damage not related to shipping,
within 7 days of receiving the
Conventions
1–512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
This paragraph contains critica l instal lat ion, con fig ur ati on, or
damage to the product, or cause harm to the user.
This paragraph contains important installation or configuration
the product from functioning correctly.
Document
The information and specifications contained in this document are subject to change
without notice. CHAUVET® assumes no responsibility or liability for any errors or
CHAUVET® reserves the right to update the
Author
Date
Editor
Date
1. BEFORE YOU BEGIN
Included
Claims
• 4BAR™ Flex
• Power Cord
• Carrying Case
• 2 L-brackets
Immediately upon receipt, carefully unpack the product and che ck the box to make sure
you have received all the parts indicated above in good condition.
If the box or the contents (the product and
shipping, or show signs of mishandling, upon receipt notify the carrier immediately, not
CHAUVET®.
carrier. In addition, keep the box and all the contents for inspection.
or concealed damage, file a claim with CHAUVET®
merchandise.
Convention Meaning
• Footswitch
• Warranty Card
• Quick Reference Guide
Information
Symbol Meaning
operation information. Failure to comply with this information may
omissions that may appear in this manual.
existing document or to create a new document to correct any errors or omissions.
You can download the latest version of this manual from www.chauvetlighting.com.
© Copyright 2013 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
A. Leon 3/8/13 D. Couppe 3/11/13
render the product partially or complet ely inopera tiv e, cau se
information. Failure to comply with this information may prevent
Useful information.
4BAR™ Flex User Manual (Rev. 7) Page 3 of 16
Product at a
x
P
x
P
P
P
P
x
P
x
Safety Notes
Do not touch the product’s housing when operating because it may be very hot.
center.
Glance
Use on Dimmer
Outdoor Use
Sound-Activated
DMX
Master/Slave
Please read the following Safety Notes carefully before working with the product. The
Notes include important safe ty infor mat ion abou t insta llation, usage, and maintenance.
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Always disconnect the product from the power source before cleaning or replacing
the fuse.
• Avoid direct eye exposure to the light source while the product is on.
• Make sure the power cord is not crimped or damaged.
• Never disconnect the product from power by pulling or tugging on the cord.
• If mounting the product overhead, always secure to a fastening device using a
safety cable.
• Make sure there are no fla m m able mat erials close to the product when operating.
•
• Always make sure that the voltage of the outlet to which y ou are conne cti ng the
product is within the range stated on the decal or rear panel of the product.
• The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
• Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
• Be sure that no ventilation slots on the product’s housing are blocked.
• Never connect the product to a dimmer.
• Make sure to replace the fuse with another of the same type and rating.
• Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket.
• The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate the
product at higher temperatures.
• In the event of a serious operating problem, stop using the product immediately.
• Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
Auto Programs
Auto-Ranging Power Supply
Replaceable Fuse
User-Serviceable
Duty Cycle
• Keep this User Manual for future use. If you sell the product to another user, be
sure that they also receive this document.
Page 4 of 16 4BAR™ Flex User Manual (Rev. 7)
2. INTRODUCTION
Product Overview
Product Dimensions
LED Display
DMX In
DMX Out
Tripod Adjustment Knob
Fuse Holder
(Power Linking)
Power In
Light Adjustment
Power Outputs for
Fuse Holder
(Power In)
Additional Fixtures
Knob (x 4)
4BAR™ Flex User Manual (Rev. 7) Page 5 of 16
AC Power
ranging power supply and it can work with an input
circuit breaker, power outlet, and
(circuit breaker or fuse). Make
an appropriate electrical ground to avoid the risk of
a rheostat (variable resistor) or dimmer circuit, even
Fuse
t
(Power Linking)
3. SETUP
The 4BAR™ Flex has an autovoltage range of 100~240 VAC, 50/60 Hz.
To determine the product’s power requirements (
wiring), use the current value listed on the label affixed to the product’s back panel, or
refer to the product’s
Technical Specifications. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a protected circuit
sure the product has
electrocution or fire.
Never connect the product to
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Replacemen
Follow the instructions below to change the power linking fuse, if necessary.
Disconnect the product from the power outlet before replacing the fuse.
1. Disconnect the product from power.
2. With a flat-head screwdriver, unscrew the fuse holder
cap from the housing.
3. Remove the blown fuse.
4. Replace with a fuse of the exact same type and rating.
5. Screw the fuse holder cap back in place and
reconnect power.
Always replace a blown fuse with another of the same type and rating.
Page 6 of 16 4BAR™ Flex User Manual (Rev. 7)
Fuse
Replacement
(Power In)
Installed fuse
(held by plastic clip)
Spare fuse holder
(inside safety cap)
Safety cap
Follow the instructions below to change the power-in fuse, if necessar y
Disconnect the product from the power outlet before replacing the fuse.
1. Disconnect the product from power.
2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
3. Pry the fuse holder out of the housing.
4. Remove the blown fuse from the holder.
5. Replace with a fuse of the exact same type and rating.
6. Insert the fuse holder back in place and reconnect power.
A spare fuse is not included; however, the safety cap has room for a spare.
4BAR™ Flex User Manual (Rev. 7) Page 7 of 16
Power Linking
of the unit.
Linking
The power linking diagram shown above corresponds to the North American
in other markets, you must
consult with the local CHAUVET® distributor as power linking connectors and
1st Product
2nd Product
3rd Product
Other products
The product provides power linking via the IEC outlet located in the back
Please see the diagram below for further explanation.
Power
Diagram
You can power link up to 12 4BAR™ Flex units on 120 VAC or up to 21 4BAR™
Flex units on 230 VAC.
version of the product ONLY! If using the product
requirements may differ in your country or region.
Page 8 of 16 4BAR™ Flex User Manual (Rev. 7)
Mounting
, read and follow the safety recommendations indicated in
may be mounted in any position; however, make sure adequate
can support
for weight information.
Mount the
always consider the length of the
knobs allow for directional adjustment when aiming the
L-brackets
Pod pan adjustment
Tripod insertion
Pod tilt adjustment
Before mounting the product
the Safety Notes.
Orientation
The 4BAR™ Flex
ventilation is provided around the produc t.
Rigging
• Before deciding on a location for the product, always make sure there is easy
access to the product for maintenance and programming purposes.
• Make sure that the structure onto which you are mounting the product
the product’s weight. Please see the Technical Specifications
• When mounting the product overhead, always use a safety cable.
product securely to a rigging point, whether an elevated platform or a truss.
• When rigging the product onto a truss, you should use a mounting clamp of
appropriate weight capacity.
• When po wer linking m ultiple products, you must
power linking cable and mount the products close enough for the cable to reach.
• The bracket adjustment
product to the desired angle. Only loosen or tighten the bracket knobs manually.
Using tools could damage the knobs.
Mounting Diagram
4BAR™ Flex User Manual (Rev. 7) Page 9 of 16
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the
Menu Map
15CH
Configuration
DMX
channel mode and the other is a
highest DMX mode, which defines
When selecting a starting DMX address, always consider the number of DMX channels
starting address is too high, access to some of the
4. OPERATION
(DMX)
display. See the Product Overview to see the button locations on the control panel.
Button Function
<MENU>
<UP>
<DOWN>
Mode Programming Steps Description
DMX
Personalities
Sound-Active
Mode
Automatic
Mode
Auto Program
Speed
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
on the product.
Press to find an operation mode or to back out of the current menu
option
Press to scroll up the list of options or to find a higher value
Press to scroll down the list of options or to find a lower value
3-CH
S-- S 1–S100
d 1-d512
SND
AUTO
Selects DMX personality and
starting address
Sets Sound-Active mode
Sets Auto Program
Sets Auto Program speed
The 4BAR™ Flex has two DMX personalities. One is a 3-
Personalities
and Starting
15-channel mode.
The 4BAR™ Flex uses up to 15 DMX channels in its
the highest configurable address to 498.
Address
the selected DMX mode uses. If the
product’s channels will be restricted.
If you are not familiar with the DMX protocol, download the DMX Primer from
www.chauvetlighting.com
To choose your starting address:
1. Press <MENU> repeatedly until 3-CH (3-channel mode) or 15CH (15-channel mode)
shows on the display.
2. Use <UP> or <DOWN> to select the starting address.
.
Page 10 of 16 4BAR™ Flex User Manual (Rev. 7)
DMX Channel Assignments and V alues
000 ó 009
RGB Color Mixing Mode
010 ó 029
Auto Program 1
030 ó 049
Auto Program 2
050 ó 069
Auto Program 3
070 ó 089
Auto Program 4
090 ó 109
Auto Program 5
110 ó 129
Auto Program 6
130 ó 149
Auto Program 7
150 ó 169
Auto Program 8
170 ó 189
Auto Program 9
190 ó 209
Auto Program 10
210 ó 229
Auto Program 11
230 ó 249
Auto Program 12
250 ó 255
Sound-Active Mode
000 ó 008
No function
009 ó 255
Dimmer 1–100%
3
Strobe
000 ó 255
0–100%
4
Red
000 ó 255
0–100%
5
Green
000 ó 255
0–100%
6
Blue
000 ó 255
0–100%
7
Red
000 ó 255
0–100%
8
Green
000 ó 255
0–100%
9
Blue
000 ó 255
0–100%
10
Red
000 ó 255
0–100%
11
Green
000 ó 255
0–100%
12
Blue
000 ó 255
0–100%
13
Red
000 ó 255
0–100%
14
Green
000 ó 255
0–100%
15
Blue
000 ó 255
0–100%
1
Red
000 ó 255
0–100%
2
Green
000 ó 255
0–100%
3
Blue
000 ó 255
0–100%
15-CH
Channel Function Value Setting
1 Control/Operating Mode
2 Dimmer
RGB Color Mixing
(Pod 1)
RGB Color Mixing
(Pod 2)
3-CH
Channel Function Value Setting
RGB Color Mixing
(Pod 3)
RGB Color Mixing
(Pod 4)
4BAR™ Flex User Manual (Rev. 7) Page 11 of 16
Configuration
s in
standalone mode may transmit DMX signals that could interfere with the DMX
to adjust the duration of each step of the automatic program
Master/Slave
unit (the “master”) to control the
thout the need of a DMX
controller. The master unit will be set to operate in either Automatic or Sound Active
ode. Once set and
channel
all the slave units before connecting the master unit to the DMX
Never connect a DMX controller to a DMX string configured for Master/Slave
may interfere with the signals from the
(Standalone)
Set the product in one of the standalone modes to contr ol without a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
Never connect a product that is operating in any standalone mode (either
Automatic or Sound) to a DMX string connected to a DMX controller. Product
signals from the controller.
Sound-Active
Mode
To enable the Sound-Active mode, do the following:
1. Press <MENU> repeatedly until SND shows on the display.
2. Turn the music on and adjust the microphone sensitivity knob until the product
starts responding to the beat of the music.
The product will only respond to low frequencies of music (bass and drums).
Automatic Mode
To enable the Automatic mode, follow the instructions below:
1. Press <MENU> repeatedly until AUTO shows on the display.
2. Press <MENU> and S 1–S100 shows on the display.
3. Use <UP> or <DOWN>
from S 1 (fast) to S100 (slow).
The Master/Slave mode allows a single 4BAR™ Flex
Mode
actions of one or more 4BAR™ Flex units (the “slaves”) wi
mode, while the slave units will be set to operate in Slave m
connected, the slave units will operate in unison with the master unit.
Configure the units as indicated below.
Slave units:
1. Press <MENU> repeatedly until 3-CH or 15CH shows on the display.
2. Use <UP> or <DOWN> to set the DMX address to d 1.
Note: The DMX address can be set from either the 3-channel or the 15DMX personality.
3. Connect the DMX input of the first slave unit to the DMX output of the master unit.
4. Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
5. Finish setting and connecting all the slave units.
Master unit:
1. Set the master unit to operate in either Automatic or Sound-Active mode.
2. Make the master unit the first unit in the DMX daisy chain.
• Configure
•
daisy chain.
operation because the controller
master unit.
• Do not connect more than 31 slave units to the master unit.
Page 12 of 16 4BAR™ Flex User Manual (Rev. 7)
Footswitch
Operation
included footswitch provides quick access to the preset colors, color change
Press pedal #1 (Preset) to activate control. When this is operating properly, the
before connecting
Disconnecting
the Footswitch
will
The
programs, and triggering via the onboard microphone on the 4BAR™ Flex:
1. Power on the fixture.
2. Connect the footswitch to the 4BAR™ Flex via the 4-pin connection cable with plug.
3.
LEDs on the 4BAR™ Flex will light white (first function on pedal #1).
Pedal Sub-option Function
1 x press White
2 x press Red
3 x press Green
4 x press Blue
1
(Preset)
5 x press Yellow
6 x press Magenta
7 x press Cyan
8 x press
9 x press
2
(Sound On)
3
(Blackout)
1 x press Sound controlled
1 x press All LEDs off (blackout)
Color change every second in a
continuous loop
Color change every three seconds in a
continuous loop
There is no need to modify any settings for the 4BAR™ Flex
the footswitch. It will operate properly in any mode.
Plug the master fixture in LAST!
In order to properly disconnect the footswitch, please follow these steps:
1. Unplug the footswitch from the 4BAR™ Flex.
2. Turn the power to the fixture off (unplug the power cable).
3. Turn the power to the fixture on again (plug in the power cable), and the fixture
properly operate on any one of the three modes.
4BAR™ Flex User Manual (Rev. 7) Page 13 of 16
Product
up reduces light output performance and can cause overheating. This can
To maintain optimum
at least twice a
5. TECHNICAL INFORMATION
Dust build-
Maintenance
lead to reduction of the light source’s life and mechanical wear.
performance and minimize wear, you should clean your lighting products
month. However, be aware that usage and environmental conditions could be
contributing factors to increasing the cleaning frequency.
To clean the product, follow the instructions below:
• Unplug the product from power.
• Wait until the product is at room temperature.
• Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents.
• Clean all transparent surfaces with a mild soap solution, ammonia-free glass
cleaner, or isopropyl alcohol.
• Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
• Softly wipe any dirt or grime to the outside edge of the transparent surface.
• Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully after cleaning them.
Page 14 of 16 4BAR™ Flex User Manual (Rev. 7)
Dimensions and
Length
Width
Height
Weight
47.4 in (1,205 mm)
5.2 in (133 mm)
14.7 in (375 mm)
13.5 lbs (6 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100~240 V, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
47 W
46 W
Operating
0.7 A
0.4 A
Power linking current (units)
8 A (12 units)
8 A (21 units)
Fuse (power linking)
T 5 A, 250 V
T 5 A, 250 V
Fuse (power in)
F 2 A, 250 V
F 2 A, 250 V
Power I/O
U.S./Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (U.S.)
Local plug
Light Source
Type
Power
Lifespan
LED
0.25 W
100,000 hours
Color
Quantity
Current
Red
144
20 mA
Green
144
20 mA
Blue
144
20 mA
Photo Optic
Parameter
Illuminance @ 2 m
725 lux (per pod)
Beam angle
21º
Field angle
33°
Thermal
Maximum External Temp.
Cooling System
104° F (40° C)
Convection
DMX
I/O Connectors
Connector Type
Channel Range
3-pin XLR
Sockets
3, 15
Ordering
Product Name
Item Code
Item Number
4BAR™ Flex
03030504
4BARFLEX
6. TECHNICAL SPECIFICATIONS
Weight
4BAR™ Flex User Manual (Rev. 7) Page 15 of 16
If you live outside the U.S., United Kingdom, or Ireland, contact your distributor of
record and follow their instructions on how to return CHAUVET® products to
Returns
Technical Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product. Be prepared to
provide the model number, serial number, and a brief description of the cause for the
epaid, in its original box, and with its original packing
will refuse any product
number
the following information on a piece of paper
properly. Any shipping damage resulting from inadequate
cretion to repair or replace
Contact Us
Fax: +44 (0)1773 511110
Email: tech@chauvetlighting.com
www.chauvetlighting.com
www.chauvetlighting.co.uk
To return a product or request support:
• In the U.S., contact CHAUVET® World Headquarters (see below).
• In the UK or Ireland, contact CHAUVET® Europe Ltd. (see below).
• In any other country, DO NOT contact CHAUVET®. Contact your distributor. See
www.chauvetlighting.com
for distributors outside the U.S., United Kingdom, or
Ireland.
them. Visit our website f or contact details.
Call the corresponding CHAUVET®
return.
You must send the merchandise pr
and accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET®
returned without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA
directly on the box.
Before sending the product, clearly write
and place it inside the box:
• Your name
• Your address
• Your phone number
• The RMA number
• A brief description of the problem
Be sure to pack the product
packaging will be your responsibility. FedEx packing or double-boxing are
recommended.
CHAUVET® reserves the right to use its own dis
returned product(s).
World Headquarters
CHAUVET®
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: (954) 577-4455
Fax: (954) 929-5560
Toll free: (800) 762-1084
Technical Support
Voice: (954) 577-4455 (Press 4)
Fax: (954) 756-8015
United Kingdom & Ireland
CHAUVET® Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: +44 (0)1773 511115
Technical Support
Email: uktech@chauvetlighting.com
World Wide Web
Page 16 of 16 4BAR™ Flex User Manual (Rev. 7)
World Wide Web
Loading...