Chauvet YA-210 User Manual

If you like this product then why not take a look at some of

the other items available from

Police Beacon

YA-210

Users Guide

Please read these instructions carefully before use

World-wide Headquarters:

3000 North 29th Ct.

Hollywood, Florida

33020

Tel: [phone]

Fax: [phone]

www.ChauvetLighting.com

COMET

52 multicolored beams rotate

and cross slowly……..

Great Atmosphere

Creator!

OCTOPUS

32 multicoloured beams
rotate back and forth to
the beat of the music…

600W of Pure Power!

ALIEN

12 colored laser sharp beams rotate
360

o

at a speed controlled by you…

Looks Incredible At Any Speed!

Remember if you’re looking for lights – Ask for CHAUVET !

Introduction

Congratulations on the purchase of your new CHAUVET lighting effect. We are confident you will
enjoy many trouble free hours with this unit. To assist with the care and use of the product we
have prepared this short guide.

Operation

This lighting effect has been designed to function on a mains power supply of either 120V~60Hz
or 230V~50Hz and has been fitted with a suitable powerplug for use with your local voltage.
Check the label on theunit and the power plug for the correct voltage.

When connected to the mains power supply the unit should illuminate and the reflector dish
should rotate.

The duty cycle for this effect should be no more than 15 minutes on then 15minutes off.

Replacing Lamps

1. Disconnect from main power supply before attempting to replace lamp.

2. Ensure that the unit is sufficiently cool, before removing blown lamp.

3. Never touch new lamps with your fingers; use a tissue or a cloth.

In order to replace the lamp, disconnect from main power supply first, and unscrew the set
screws to remove the lamp replacement cover, which is highlighted on the diagram (fig.1). Only
use the appropriately rated lamps as use of any other lamp type may cause the unit to be non­operational.

Finally before switching on, check that the lamp is housed correctly in the lamp holder and that
the lamp replacement cover has been screwed back into place.

If after replacement of the lamp, the unit is still not working then please contact

CHAUVET for servicing.

Cleaning

The most important part of your lighting effect to keep clean is the colored dome and the reflector
dish as they allow the light output to transmit. These should be cleaned with a soft damp cloth.
The body of the unit may alsobe cleaned in the same way. We recommend internal cleaning be
carried out by a fully qualified technician.

Maintenance & Servicing

Work on internal parts should be carried out by a qualified technician. Removal of any covers
o

ther than the lamp replacement access is considered a breach of warranty and will not be

covered under any such agreement unless authorized first by CHAUVET.

Troubleshooting

• If the unit is not functional – check main power supply is ‘on’ and check fuses.

• If the unit is functional but lamp does not light - lamp may require replacing.
If after trying this solution you still have a problem contact your dealer or CHAUVET.

Caution

No user serviceable parts inside, please refer to CHAUVET for service.

Power Connections

The unit is supplied with a power plug appropriate to its voltage and destination. Should any other
connections be required they must be carried out with the following configuration.

Earth = Green/Yellow cable
Neutral = Blue cable
Live = Brown cable

In the USA & Europe, it is required that all plugs are 3-pin type i.e. with Earth/Ground connection
In the UK, it is required that all mains plugs are fitted with 5A fuses.

Technical Specifications

Power

120V~60Hz AC

230V~50Hz AC

Lamps

1 x 120V 75W

1 x 230V 75W

Dimensions

254mm / 10in

Weight

2.3kg / 5lbs

User Information (Please complete for your records)

Date Purchased: // Serial No:
Dealer Stamp: Model: YA-210 POLICE BEACON

Fig. 1

Lamp Replacement Cover

Mounting Base