Chauvet VIP Drive 43s User Manual

Page 1
User Manual
Page 2
EDITION NOTES
The VIP Drive 43s User Manual includes a description, safety precautions, installation, programming, operation, and maintenance instructions for the VIP Drive 43s as of the release date of this edition.
Trademarks
Copyright Notice
The works of authorship contained in this manual, including, but not limited to, all design, text and images are owned by Chauvet.
© Copyright 2016 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States of America.
Manual Use
Chauvet authorizes its customers to download and print this manual for profession al information pu rposes only. Chauvet expressly prohibits the usage, copy, storage, distribution, modification, or printing of this manual or its content for any other purpose without written consent from Chauvet.
Document Printing
For best results, print this document in color, on letter size paper (8.5 x 11 in), double-sided. If using A4 paper (210 x 297 mm), configure the printer to scale the content accordingly.
Intended Audience
Any person installing, operating, and/or maintaining this product should comple tely read thro ugh the guide that shipped with the product, as well as this manual, before installing, operating, or maintaining this product.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects. However, Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss, damage or disruption caused by any errors or omissions in this document, whether such errors or omissions result from negligence, accident or any other cause. Chauvet reserves the right to revise the content of this document without any obligation to notify any person or company of such revision, howe ver , Chauvet has no obligation to make, and does not co mmit to make, any such revisions. Download the latest version from www.chauvetprofessional.com
.
Document Revision
This VIP Drive 43s User Manual is the 1st edition of this document. Go to www.chauvetprofessional.com for the latest version.
VIP Drive 43s User Manual Rev. 1
Page 3
TABLE OF CONTENTS
1. Before You Begin....................................................................... 1
What Is Included ........................................................................................... 1
Claims........................................................................................................... 1
Manual Conventions ..................................................................................... 1
Symbols ........................................................................................................ 1
Safety Notes.................................................................................................. 2
Personal Safety.............................................................................................................. 2
Mounting ........................................................................................................................ 2
Power and Wiring........................................................................................................... 2
Operation ...................................................................................................... 2
2. Introduction ................................................................................ 3
Description.................................................................................................... 3
Features........................................................................................................ 3
Product Overview.......................................................................................... 3
Front Panel Overview..................................................................................................... 3
Rear Panel Overview..................................................................................................... 4
Product Dimensions...................................................................................... 4
3. Setup ........................................................................................... 5
AC Power...................................................................................................... 5
AC Plug......................................... ... ... ... .... ... ... ... ....................................... ... .... ... ... ... .... 5
Mounting ....................................................................................................... 5
Signal Connections....................................................................................... 5
Video Source Connection .............................................................................................. 5
Computer Connection.................................................................................................... 5
Art-Net™ Connection..................................................................................................... 5
Preview Monitor Connection......................... ... ... .... ... .......................................... ... ... ... . 5
Connection Diagrams.......................... ... .... ... ... ... .... ... .......................................... ... ... ... . 6
Input Connections Diagram..................................................................................... 6
Output Connections Diagram .................................................................................. 6
4. Operation .................................................................................... 7
Control Panel Operation................................................................................ 7
Programming................................................................................................. 7
Menu Map..................................................................................................... 7
Operating Settings Configuration.................................................................. 13
Home Screen................................................................................................................. 13
Brightness...................................................................................................................... 14
Front Panel Lock............................................................................................................ 14
Color Adjustments.......................................................................................................... 14
Ethernet.......................................................................................................................... 15
Art-Net™ Start Address........................................................................................... 15
Art-Net™ Universe .................................................................................................. 15
IP Address....................................... .... ... .......................................... ....................... 15
Subnet Mask............................................................................................................ 16
Art-Net™ Values............................................................................................................ 16
Backup........................................................................................................................... 20
Save Configuration................................. ... ... .... ... ... ... .... ... ... .................................... 21
Load Configuration ....... ... .... ... ... ... ... .... ... ... ... .... .......................................... ... ... ... ... . 21
Load One Configuration from USB.......................................................................... 21
Load All from USB................................................................................................... 21
Save All to USB....................................................................................................... 21
Transition ....................................................................................................................... 21
VIP Drive 43Nova User Manual Rev. 1
i
Page 4
Deinterlacing............................................................................................................ 21
Image Enhance ....................................................................................................... 22
Fade Type ................................. .............................................................................. 22
Fade Time ................................. .............................................................................. 22
Test Pattern.................................................................................................................... 23
Test Pattern Mode................................................................................................... 23
Auto Switch.............................................................................................................. 24
Picture In Picture................................. ... .... ... ... ... .......................................... .... ... .......... 24
Input Selection.............. ... ........................................................................................ 24
Position.................................................................................................................... 24
Input Mode.......... .... ... ... ... .......................................... .... ... ....................................... 25
Swap Inputs............... ... ... .... ... ... ... ... .......................................... .............................. 25
Display Brightness ......................................................................................................... 25
Video Input..................................................................................................................... 25
Temperature................................................................................................................... 26
Advanced....................................................................................................................... 26
Firmware Version .................................................................................................... 26
Double-tap To Switch .............................................................................................. 26
Preview Output....................................... ... ... .... ... ... ... .... ......................................... . 26
Preview DVI Port .......... ... .... ... .......................................... ... ... ................................. 26
Factory Reset .. ... .... ................................................................................................. 27
Customized Button .... ... ... .... ... ... ... ... .... .......................................... ... ... ... .... ... ... ....... 27
Output Format ......................................................................................................... 27
Scale.............................................................................................................................. 27
Horizontal Size ........................................................................................................ 27
Vertical Size..... ... ................................................................................. .................... 28
Horizontal and Vertical Scale .................................................................................. 28
Horizontal Offset...................................................................................................... 28
Vertical Offset.................................. .... ... ... .............................................................. 28
Auto Scale ............................................................................................................... 28
Reset Scaling .......................................................................................................... 29
Zoom/Crop Image.................................................................................................... 29
Map................................................................................................................................ 29
Offset Settings................................. .... ... ... .............................................................. 29
Position Settings........... ... .... ... ... ... ... .... ... ................................................................. 30
Port Tutorial......................................... ... ... ... .... .......................................... ... ... ....... 30
Set Width................................................................................................................. 31
Test Grid.................................................................................................................. 31
Mapping by Port ...................................................................................................... 32
5. Technical Information................................................................ 34
Product Maintenance.................................................................................... 34
6. Technical Specifications ........................................................... 35
7. Returns........................................................................................ 36
8. Contact Us .................................................................................. 37
ii
VIP Drive 43Nova User Manual Rev. 1
Page 5
BEFORE YOU BEGIN

1. BEFORE YOU BEGIN

What Is Included

VIP Drive 43s
4 Rubber Feet
Neutrik® powerCON® Power Cord

Claims

Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition.
If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier immediately may invalidate your claim. In addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or concealed damage, file a claim with Chauvet within 7 days of delivery.

Manual Conventions

CONVENTION MEANING
1–512 A range of values
50/60 A set of values of which only one can be chosen
<SET> A button on the product’s control panel
Settings A product function or a menu option
USB Cable
USB A to B Adapter
Warranty Card

Symbols

SYMBOL MEANING
Electrical warning. Not following these instructions may cause electrical damage to the product, accessories, or the user.
Critical installation, configuration, or operation information. Not following these instructions may make the product not work, ca use damage to the product, or cause harm to the operator.
Important installation or configuration information. The product may not function correctly if this information is not used.
Useful information.
Any reference to power connections in this manual assu mes the use of Ne utrik® powerCON® cables.
The term “DMX” used throughout this manual refers to the USITT DMX512-A digital data transmission protocol.
VIP Drive 43s User Manual Rev. 1
1
Page 6
BEFORE YOU BEGIN

Safety Notes

Read all the following safety notes before working with this product. These notes contain important information about the installation, usage, and maintenance of this product.
This product contains no user-serviceable parts. Any reference to servicing in this User Manual will only apply to properly trained, certified technicians. Do not open the housing or attempt any repairs.
All applicable local codes and regulations apply to proper installation of this product.

Personal Safety

Avoid direct eye exposure to the light source while the product is on.
Always disconnect the product from the power source before cleaning or replacing the fuse.
Always connect the product to a grounded circuit to avoid the risk of electrocution.
Do not touch the product’s housing when operatin g be ca us e it ma y be ve ry ho t.

Mounting

This product is for indoor use only! To prevent risk of fire or shock, do not expose this product to rain or moisture. (IP20)
CAUTION: When transferring product from extreme temperature environments, (e.g. cold truck to warm humid ballroom) condensation may form on the internal electronics of the product. To avoid causing a failure, allow product to fully acclimate to the surrounding envir onment before connecting it to power.
Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces.
Make sure there are no flammable materials close to this product while it is operating.
Never carry the product by the power cord .

Power and Wiring

Make sure the power cord is not crimped or damaged.
Always make sure you are connecting this product to the proper voltage in accordance with the specifications in this manual or on the product’s specification label.
To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it.
Never connect this product to a dimmer pack or rheostat.
Never disconnect this product by pulling or tugging on the power cable.

Operation

Do not operate this product if there is damage on the housing or cables. Have the damaged parts replaced by an authorized technician at once.
Do not cover the ventilation slots when operating to avoid internal overheating.
The maximum ambient temperature is 1 13 °F (4 5 °C). Do not operate the product at higher temperatures.
In the event of a serious operation problem, stop using this product immediately!
If your Chauvet product requires service, contact Chauvet Technical Support.
2
VIP Drive 43s User Manual Rev. 1
Page 7
INTRODUCTION
1 2678
35
910
4

2. INTRODUCTION

Description

The VIP Drive 43s is a streamlined all in one video wall mapper/scal er/switcher designed for u se with Linsn video control protocol. With 4 inputs, 3 outputs and a preview monitor, the VIP Drive 43s will map your wall, scale/switch your video source, and allow remote triggering via Art-Net (DMX over Ethernet) eliminating the need for individual mappers, scalers, an d vi deo switchers. HDCP support and EDID management further improve the flexibility of the VIP Drive 43s.

Features

Video wall processor that switches, scales, and outputs video signa l to any Linsn video panels (including PVP S5, PVP X3, PVP X6IP, C6)
Powerful standalone mapping for video panels, without a computer.
Custom user interface makes setting up your wall fast and easy
Front, integrated video screen assists switching and timing for live events
Remote control via Art-Net supports mapping, triggering, and video adjustments, including scaling and positioning
Supports DVI, HDMI, and HD-SDI for flexibility in various applications
Includes 4 etherCON video outputs to support full HD at 2.6 million LED resolution
Works with LED Studio for complex configurations and panel calibration
Compact 1U packing eases transportation and integration into your existing setup

Product Overview

Front Panel Overview

# NAME FUNCTION 1 Menu Display An interface for the menu options of the product
Press to enable the currently selected menu option or set the currently
SCROLL/ENTER
2
3 MENU Button Press to return to the previous menu level. 4 SCALE Button Accesses the Scale menu. Can also be set to Black Out or Freeze . 5MAP ButtonAccesses the Map menu. Can also be set to Black Out or Freeze. 6 HDMI Button
8DVI Button 9
10 Preview Display Previews selected input source before output to video panel
Knob
USB Port
(Type B)
selected value into the selected function. Turn clockwise to scroll down throug h the menu or increase a valu e when in a function. Turn counter-clockwise to scroll up through the menu or decrease a value when in a function.
Select input source7SDI Button
Control port to interface with computer
VIP Drive 43s User Manual Rev. 1
3
Page 8

Rear Panel Overview

1 23457 10
6
9
8
17.3 in
439 mm
2 in
51 mm
1.7 in
44 mm
1 in
25 mm
17.4 in
443 mm
12 in
305 mm
19 in
483 mm
9.8 in
248 mm
# NAME FUNCTION 1 HDMI Input HDMI video input
2 DVI Input DVI video input 3 4 DVI PREVIEW OUT For output preview on an external monitor 5 USB Port (Type A)
6
7
8
9
10
SD/HD/3G-SDI
Input
Ethernet Slave In
Port
Ethernet Slave Out
Port
Art-Net™ Through
Ports
Neutrik®
etherCON® Ports
Neutrik®
powerCON® Input
SDI video input
For connecting to a computer, or for USB cascade output (control only, no video)
Reserved for future use Reserved for future use For Art-Net™ control For output to LED video panels Power input
INTRODUCTION

Product Dimensions

4
VIP Drive 43s User Manual Rev. 1
Page 9
SETUP

3. SETUP

AC Power

Each VIP Drive 43s has an auto-ranging power supply that works with an input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the power requirements for each VIP Drive 43s, refer to the label affixed to the product. You can also refer to the Technical Specifications chart in this manual.
The listed current rating indicates the maximum current draw during normal operation. For more information, download Sizing Circuit Breakers from the Chauvet website: www.chauvetprofessional.com
• Always connect the product to a protected circuit (circuit breaker or fuse). Make sure the product has an appropriate electrical ground to avoid the risk of electrocution or fire.
• T o eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it.
Never connect the product to a rheostat (variab le resistor ) or dimmer circuit , even if the rheostat or dimmer channel serves only as a 0 to 100% switch.

AC Plug

The VIP Drive 43s comes with a power input cord terminated with a Neutrik® powerCON® connector on one end and an Edison plug on the other end (U.S. market). If the power input cord that came with your product has no plug, or if you need the change the plug, use the table below to wire the new plug.
CONNECTION WIRE (U.S.) WIRE (EUROPE) SCREW COLOR
AC Live Black Brown Yellow or Brass
AC Neutral White Blue Silver
AC Ground Green/Yellow Green/Yellow Green
.

Mounting

The VIP Drive 43s fits nicely on a standard 19” rack, or it can be placed on its rubber feet on a flat level surface.

Signal Connections

The VIP Drive 43s uses the Linsn control protocol to send video signal to the connected panels. The VIP Drive 43s has USB and Ethernet ports for interfacing with a computer, HDMI, SDI and DVI ports for video input, as well as 4 Neutrik® etherCON® out ports, a DVI out port, 2 ethernet slave ports, and 2 ethernet ports for Art-Net™ control.

Video Source Connection

You can link the VIP Drive 43s directly to a video source using a DVI connection, an HDMI connection, or an SDI connection.

Computer Connection

You can link the VIP Drive 43s to a computer running video mapping software (such as LED Studio) using a USB (type A or B) connection. This will provide control options for the VIP Drive 43s through a computer interface. Download the LED Studio software and User Manual from www.chauvetvideo.com

Art-Net™ Connection

With Art-Net™, you can control the mapping and scaling, as well as the color balance and dimmer levels for all connected panels. You can link the VIP Drive 43s to a controller using an ethernet connection. If using other Art-Net™-compatible products with this product, you can control each individually with a single controller. The Art-Net™ Values section provides detailed information regard ing the control channels.
Art-Net™ is an Ethernet protocol that uses TCP/IP which transfers a large amount of DMX512 data us ing an Neutrik® etherCON® RJ45 connection over a large network. An Art-Net™ protocol document is available from www.chauvetprofessional.com
Art-Net™ designed by and copyright Artistic Licence Holdings Ltd.
.

Preview Monitor Connection

Y o u can link the VIP Drive 43s to a monitor that will preview the LED output using a DVI cable plugged into the PREVIEW OUT port. This port can also be set to forward the selected input signal to another product. (See Preview DVI Port
)
.
VIP Drive 43s User Manual Rev. 1
5
Page 10

Connection Diagrams

2 3
4
51 6
7
1 2 3 54
Input Connections Diagram
# CONNECTIONS PURPOSE 1 HDMI Link to an HDMI signal
2 DVI Link to a computer video output 3 SDI Link to a video device, such as a camera or a DVD player 4 Slave Ethernet Reserved for future use 5 Art-Net™ Ethernet Link to an Art-Net™ networ k 6 Neutrik® powerCON® Receive AC power 7 USB Type B Interface with a computer
SETUP
Output Connections Diagram
# CONNECTIONS PURPOSE 1 DVI Preview monitor or another product
2 USB Type A Interface with a computer 3 Slave Ethernet Reserved for future use 4 Art-Net™ Ethernet Link to an Art-Net™ network 5 Neutrik® etherCON® LED video panels, such as the PVP X6IP from CHAUVET
6
VIP Drive 43s User Manual Rev. 1
Page 11
OPERATION

4. OPERATION

Control Panel Operation

See the Product Overview for a detailed description of the control panel.

Programming

Refer to the Menu Map to understand the menu options. The menu map shows the main level an d a variable number of programming levels for each option.
To access the menu from the Home Screen, press the <MENU> button.
To scroll through the options on each level of the menu, turn the <SCROLL/ENTER> knob. Turn it clockwise to scroll down, and turn it counter-clockwise to scroll up.
Press the <SCROLL/ENTER> knob to select the highlighted option. This will take you to the next programming level for that option, or it will highlight a value that can be edited.
To increase a selected number value, turn the <SCROLL/ENTER> knob clockwise. To decrease a selected number value, turn the <SCROLL/ENTER> knob counter-clockwise.
Press <MENU> to exit to the previous main level.

Menu Map

MAIN LEVEL PROGRAMMING LEVELS DESCRIPTION Brightness 0–100 Controls total output level
Front Panel
Lock
Color
Adjustments
Ethernet
Backup
Front Panel Lock
Contrast 0–100 Sets contrast level Saturation 0–100 Sets saturation level Sharpness 0–100 Sets sharpness
Gamma
Color
T emperature
Art-Net Start Address 1–512 Sets Art-Net™ starting address
Art-Net Universe 0–255 Sets Art-Net™ universe
IP Address
Save Setup Load Setup
Load Single From
Load all from USB
Save all to USB
Color
T emperature
USB
Off On
Custom
Reset Resets color adjustments
Local IP
Address
Subnet
Mask
Input New Password
0000–9999
Linear Linear gamma correction
sRGB sRGB gamma correction
-1.2
1.2
-1.4
1.4
-1.6
1.6
Full RGB
Red Level 0–255 Green Level Blue Level 0–255
_ _ _._ _ _._ _ _._ _ _
(000–255)
_ _ _._ _ _._ _ _._ _ _
(000–255)
Save1–10
All
0–255
Locks the control functions on the front panel.
Sets gamma correction level
Color temperature is full white Sets maximum value of selected
color to control color temperature
Sets IP address Sets Subnet mask
Saves and loads configurations <SCROLL/ENTER> knob to confirm.
<MENU> button to cancel.
VIP Drive 43s User Manual Rev. 1
7
Page 12
MAIN LEVEL PROGRAMMING LEVELS DESCRIPTION
Off On Off On
Dissolve Fade dissolve
Cut Quick cut
Wipe Square In Square wipe inward
Wipe T_L In Top left wipe inward
Wipe T_L Top left wipe outward
Wipe T_R In Top right wipe inward
Wipe T_R
Wipe B_L In
Wipe B_L Bottom left wipe outward
Wipe B_R In
Wipe B_R Bottom right wipe outward
Wipe Left In Left wipe inward
Wipe Left Left wipe outward
Wipe Right In Right wipe inward
Wipe Right Right wipe outward
Wipe Top In Top wipe inward
Wipe Top Top wipe outward
Wipe Bottom In Bottom wipe inward
Wipe Bottom
Off On
Off
1–10s
(Mode 19
Only)
(Mode 20
Red
Off On
Only)
Enables/Disables Deinterlacing Enables/Disables Image
Enhance
Square wipe outward
Top right wipe Bottom left wipe inward
Bottom right wipe inward
Bottom wipe outward
Enables/disables test pattern
Turns off or sets switch time
Edits color of Test Pattern Mode 19
Sets number of horizontal steps in gradient of Test Pattern Mode 20
Sets number of vertical steps in gradient of Test Pattern Mode 20
Selects color of gradient of Test Pattern Mode 20
Enables/disables Picture In Picture
Image Enhance
Transition
Test
Pattern
PIP PIP
Deinterlace
Wipe Square Ou
Fade Type
Fade 0.0-3.0s (increments of 0.5s) Defines fade time
Test Pattern
Mode 1–20 Selects test pattern
Auto Switch
Red
Green
Blue
HOR STEP 2–64 (by doubles)
VER STEP 0–64 (increments of 4)
COLOR
0–255
Green
Blue
White
OPERATION
outward
8
VIP Drive 43s User Manual Rev. 1
Page 13
OPERATION
MAIN LEVEL PROGRAMMING LEVELS DESCRIPTION
Default Unchanged inputs HDMI/DVI Input 1: DVI / Input 2: HDMI HDMI/SDI Input 1: SDI / Input 2: HDMI
SDI/DVI Input 1: DVI / Input 2: SDI SDI/HDMI Input 1: HDMI / Input 2: SDI DVI/HDMI Input 1: HDMI / Input 2: DVI
DVI/SDI Input 1: SDI / Input 2: DVI
L+T Top left position R+T Top right position L+B Bottom left position
R+B Cent Center position
L+R Left and right position T+B Top and bottom position
INPUT1
INPUT2
Off Input 1 is the foreground On Input 1 is the background
Auto Detects input format
RGB DVI Receive RGB DVI over HDMI
RGB HDMI Receive RGB HDMI
PREVIEW DVI Match format to PREVIEW OUT
FOLLOW Reserved for future use
CUSTOM
Auto Detects input format
PREVIEW DVI Match format to PREVIEW OUT
FOLLOW Reserved for future use
CUSTOM
Celsius
Fahrenheit
Off On
Pre
Post
Preview DVI port outputs preview
Program DVI port outputs video
_ _ _ _x
_ _ _ _@
_ _
RGB DVI Receive RGB DVI
_ _ _ _x
_ _ _ _@
_ _
Bottom right position
Selects which input can be scaled or changed with buttons
Sets the brightness of the menu display
Define input parameters
Define input parameters
Selects temperature unit Displays current product
temperature in selected unit
Enables/disables double-tap to switch input sources
Selects original video or edited video to preview
PIP (cont.)
OLED
Brightness
Video Input
T emperature
Advanced
Input
Position
Select
Swap
1–15
HDMI
DVI
SDI Auto Detects input format
Temperature
Temperature _ _ C/F
Firmware Version _._ _ Displays firmware version
Double-tap To
Preview Output
Preview DVI Port
Overwrite
Overwrite
Switch
EDID
Source
EDID
Source
VIP Drive 43s User Manual Rev. 1
9
Page 14
MAIN LEVEL PROGRAMMING LEVELS DESCRIPTION
Resets product to factory defaults
Selects preset output resolution and refresh rate
Sets width and height of video output in proportion with resolution
Enables/disables Auto Scale
Sets top and bottom zoom in proportion
Advanced
(cont.)
Scale
Factory Reset
Scale Button navigates to Scale menu
Scale
Customized Button
Map
Output Format Standard
H Size 2–_ _ _ _ Sets width of video output V Size 2–_ _ _ _ Sets height of video output
H/V Size 2–_ _ _ _
H Position 0–(H Size) Sets horizontal offset V Position 0–(V Size) Sets vertical offset
Auto Scale
Reset Resets scale
Scale Mode Global Scale Reserved for future use
Top 0–_ _ _ _ Sets zoom from top
Bottom 0–_ _ _ _ Sets zoom from bottom
Top/Bottom 0–_ _ _ _
Left 0–_ _ _ _ Sets zoom from left
Right 0–_ _ _ _ Sets zoom from right
Advanced
Zoom/
Crop
Image
Blackout Button blacks out panels
Freeze Button freezes output
Map Button navigates to Map menu
Blackout Button blacks out panels
Freeze Button freezes output
800x600@60 1024x768@60 1024x768@75 1280x720@60 1280x720@50 1280x768@60 1280x800@60
1280x1024@60
1360x768@60 1366x768@60
1400x1050@60
1440x900@60
1600x1200@60 1680x1050@60 1920x1080@60 1920x1080@50 1920x1200@60 2048x1152@60
2560x812@60 2560x816@60
No
Yes
OPERATION
10
VIP Drive 43s User Manual Rev. 1
Page 15
OPERATION
MAIN LEVEL PROGRAMMING LEVELS DESCRIPTION
Sets left and right zoom in proportion
Sets horizontal offset for ports 1 and 2
Sets vertical offset for ports 1 and 2
Sets horizontal offset for ports 3 and 4
Sets vertical offset for ports 3 and 4
Sets horizontal and vertical positions of each port
Enter width and height of panel assembly
Enter number of pixels per panel
Enables/disables test grid
Selects color of gridGreen
Selects pattern of grid
Move test panel manually, based on numbers mapped
Scale
(cont.)
Map
Zoom/
Advanced
(cont.)
Offset Settings
Position Settings
Port
Tutorial
Set Width
Test Grid
Crop
Image
(cont.)
Port 1–4
H Size
Port Port 1–4 Selects port to output test grid
Test Grid
Grid
Color
Type
Test
Patterns
Moving 1–255 Auto move speed, fast to slow
Left/Right 0–_ _ _ _
Center 0–_ _ _ _ Sets all zoom in proportion
Reset Resets zoom settings
Port 1/2 Offset X 0–65535
Port 1/2 Offset Y 0–65535
Port 3/4 Offset X 0–65535
Port 3/4 Offset Y 0–65535
Port 1 X 0–6553 5 Port 1 Y 0–65535 Port 2 X 0–6553 5 Port 2 Y 0–65535 Port 3 X 0–6553 5 Port 3 Y 0–65535 Port 4 X 0–6553 5 Port 4 Y 0–65535
Auto Auto detect panels
Wall Size:
Panel
Manual
Manual 2–_ _ _ _ Define width in pixels manually
Set Width Saves setting
Manual
Pixel
Count:
T otal Pixel
Res: Auto Populates width from mapping
Off On
Red
Yellow
Cross
Row
Column
Rectangle
Auto Move Test panel moves automatically
H Position 1–_ _ V Position 1–_ _
1–255x1–
255
1–999x
1–999
_ _ _ _ _ _ Displays total number of pixels
VIP Drive 43s User Manual Rev. 1
11
Page 16
MAIN LEVEL PROGRAMMING LEVELS DESCRIPTION
Red
Preset test panel colorsGreen
Test Grid
(cont.)
Wall Size WxH 1–255x1–255
Panel Pixel WxH 1–999x1–999 Sets number of pixels per panel
Connection Type Sets data flow path
Wall Size WxH 1–255x1–255
Panel Pixel WxH 1–999x1–999 Sets number of pixels per panel
Patterns
Color
Custom
Port 1 The following options for port 1
Save To Port Saves configuration settings
Port 2 The following options for port 2
Blue
Red
0–255 Custom test panel colorGreen
Blue
Sets number of panels connected to port 1
Sets number of panels connected to port 2
OPERATION
Map (cont.)
Connection Type Sets data flow path
Save To Port Saves configuration settings
Port 3 The following options for port 3
Wall Size WxH 1–255x1–255
Panel Pixel WxH 1–999x1–999 Sets number of pixels per panel
Connection Type Sets data flow path
Save To Port Saves configuration settings
Port 4 The following options for port 4
Wall Size WxH 1–255x1–255
Panel Pixel WxH 1–999x1–999 Sets number of pixels per panel
Connection Type Sets data flow path
Save To Port Saves configuration settings
Reset Reset mapping
Sets number of panels connected to port 3
Sets number of panels connected to port 4
12
VIP Drive 43s User Manual Rev. 1
Page 17
OPERATION
1 2
3
4

Operating Settings Configuration

Home Screen

The VIP Drive 43s has a home screen that shows the current inp ut source s, resol utions, refresh rates, and other operating settings. To see the home screen, wait until the display times out, or press <MENU> repeatedly until it shows on the display. To access the main menu from the home screen, press <MENU>.
1. With PIP off: shows the currently selected input source, resolution, and refresh rate. With PIP on: shows the Input 1 source. resolution, and refresh rate.
2. With PIP off: shows the currently previewed input source, resolution, and refresh rate. With PIP on: shows the Input 2 source. resolution, and refresh rate.
3. Shows the output resolution and refresh rate.
4. Shows the status of the product, with the following icons:
ICON MEANING ICON MEANING ICON MEANING
Displays current Port 1 Data Flow
No save is loaded Auto-Scale is disabled
Save1 is loaded PIP is disabled
Save2 is loaded PIP is enabled
Save3 is loaded
Save4 is loaded Fade is set to Cut
Save5 is loaded
Save6 is loaded
Save7 is loaded
Save8 is loaded
Auto-Scale is enabled
Fade Type is set to
Dissolve
Fade Type is set to
Wipe Square In
Fade Type is set to
Wipe Square Ou
Fade Type is set to
Wipe T_L In
Fade Type is set to
Wipe T_L
Fade Type is set to
Wipe B_R In
Fade Type is set to
Wipe B_R
Fade Type is set to
Wipe Left In
Fade Type is set to
Wipe Left
Fade Type is set to
Wipe Right In
Fade Type is set to
Wipe Right
Fade Type is set to
Wipe Top In
Fade Type is set to
Wipe Top
Fade Type is set to
Wipe Bottom In
Fade Type is set to
Wipe Bottom
Save9 is loaded
Save10 is loaded
Display is not locked
Display is locked
VIP Drive 43s User Manual Rev. 1
Fade Type is set to
Wipe T_R In
Fade Type is set to
Wipe T_R
Fade Type is set to
Wipe B_L In
Fade Type is set to
Wipe B_L
Output is video playback
Output is frozen
Output is test pattern
13
Page 18
OPERATION

Brightness

The brightness setting controls the total output level of the connected video panels.
1. Press <MENU> to access the menu.
2. Turn the <SCROLL/ENTER> knob until Brightness is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the brightness, from 0–100.
5. Press the <SCROLL/ENTER> knob.

Front Panel Lock

The front panel interface of the VIP Drive 43s can be locked with a 4-digit passcode.
1. Press <MENU> to access the menu.
2. Turn the <SCROLL/ENTER> knob until Front Panel Lock is selected.
3. Press the <SCROLL/ENTER> knob. Front Panel Lock should be selected. Press the <SCROLL/ENTER> knob again.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select Off or On.
5. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the first digit, from 0–9. Repeat with the second, third, and fourth digits. Select each digit carefully.
6. Press the <SCROLL/ENTER> knob.
7. Repeat step 5 to enter the same number, to confirm the new passcode.
8. Press the <SCROLL/ENTER> knob.
To unlock the front panel interface of the VIP Drive 43s:
1. Press <MENU>, <SCALE>, <MAP>, or the <SCROLL/ENTER> knob.
2. Use the <SCROLL/ENTER> knob to enter the passcode as it was set in the previous instruction. Alternatively, entering 1 2 1 2 will also unlock the front panel interface.
3. Press the <SCROLL/ENTER> knob.

Color Adjustments

The Color Adjustments settings control output settings such as the contrast and color balance.
Contrast controls the separation of different colors in the output.
Saturation controls the intensity of all colors.
Sharpness determines the amount of detail in the output.
Color T emperature sets maximum values for each color, which affects the color temperature of the
video output.
Gamma controls the gamma correction, which applies a non-linear function to the tonal ranges in
the video before output, which balances the brightness and darkness of the resulting video.
Reset sets Color Adjustment settings to back to default.
To alter the Color Adjustment settings:
1. Press <MENU> to access the menu.
2. Turn the <SCROLL/ENTER> knob until Color Adjustments is selected.
3. Press the <SCROLL/ENTER> knob.
4. Use the <SCROLL/ENTER> knob to select from Contrast, Saturation, Sharpness, Red Level, Color Temperature, or Reset.
5. For:
Contrast, Saturation, or Sharpness:
a. Press the <SCROLL/ENTER> knob. b. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or
decrease the selected value, from 0–100.
c. Press the <SCROLL/ENTER> knob.
Gamma:
a. Press the <SCROLL/ENTER> knob. b. Use the <SCROLL/ENTER> knob to select from Linear, sRGB, -1.2, 1.2, -1.4, 1.4, -
1.6, or 1.6.
c. Press the <SCROLL/ENTER>
knob.
14
VIP Drive 43s User Manual Rev. 1
Page 19
OPERATION
Color Temperature:
a. Press the <SCROLL/ENTER> knob. b. Use the <SCROLL/ENTER> knob to select from Full RGB or Custom. c. Press the <SCROLL/ENTER> knob. d. If Custom was selected, use the <SCROLL/ENTER> knob to select from Red Level,
Green Level, or Blue Level. e. Press the <SCROLL/ENTER> knob. f. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or
decrease the maximum value of the selected color, from 0–255. g. Press the <SCROLL/ENTER> knob. h. Repeat steps d-g until the color temperature is set as desired.
Reset, press the <SCROLL/ENTER> knob.

Ethernet

The VIP Drive 43s can connect with an Art-Net™ controller to allow control of a majority of the product’s settings.
The Ethernet settings control the Art-Net™ and network addressing for the product. To access the Ethernet menu:
1. Press <MENU> to access the menu.
2. Turn the <SCROLL/ENTER> knob until Ethernet is selected.
3. Press the <SCROLL/ENTER> knob.
Art-Net™ Start Address
The VIP Drive 43s uses 95 channels, which makes the highest recommended starting address 418.
1. Access the Ethernet
2. Turn the <SCROLL/ENTER> knob until Art-Net Start Address is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the address, from 1–512.
5. Press the <SCROLL/ENTER> knob.
Art-Net™ Universe
To select in which Art-Net™ universe the VIP Drive 43s is addressed:
1. Access the Ethernet
2. Turn the <SCROLL/ENTER> knob until Art-Net Universe is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the universe address, from 0–255.
5. Press the <SCROLL/ENTER> knob.
IP Address
To set the IP address of the VIP Drive 43s:
1. Access the Ethernet
2. Turn the <SCROLL/ENTER> knob until IP Address is selected.
3. Press the <SCROLL/ENTER> knob.
4. Press the <SCROLL/ENTER> knob again
5. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the first digit, from 000–255.
6. Press the <SCROLL/ENTER> knob.
7. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the next digit, from 000–255.
8. Repea t step s 6 an d 7 twic e.
9. Press the <SCROLL/ENTER> knob.
menu.
menu.
menu.
VIP Drive 43s User Manual Rev. 1
15
Page 20
OPERATION
Subnet Mask
To set the subnet mask of the VIP Drive 43s:
1. Access the Ethernet
2. Turn the <SCROLL/ENTER> knob until Subnet Mask is selected.
3. Press the <SCROLL/ENTER> knob.
4. Press the <SCROLL/ENTER> knob again
5. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the first digit, from 000–255.
6. Press the <SCROLL/ENTER> knob.
7. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the next digit, from 000–255.
8. Repea t step s 6 an d 7 twic e.
9. Press the <SCROLL/ENTER> knob.

Art-Net™ Values

CHANNEL FUNCTION VALUE PERCENT/SETTING
1 Master Dimmer 000 255 0–100% 2 Port 1 Dimmer 000 3 Port 2 Dimmer 000 4 Port 3 Dimmer 000 5 Port 4 Dimmer 000 6 Contrast 000 7 Saturation 000
8Control
9Test Patterns
10 HDMI Trigger/Dimmer
11 DVI Trigger/Dimmer
12 SDI Trigger/Dimmer
menu.
255 0–100% 255 0–100% 255 0–100% 255 0–100% 255 0–100% 255 0–100%
000
010 No function
011
020 Soft reset
021
189 Reserved for future use
190
195 Enable Map functions
196
200 Factory reset
201
255 Reserved for future use
000
009 No function
010
019 Test pattern 1
020
029 Test pattern 2
030
039 Test pattern 3
040
049 Test pattern 4
050
059 Test pattern 5
060
069 Test pattern 6
070
079 Test pattern 7
080
089 Test pattern 8
090
099 Test pattern 9
100
109 Test pattern 10
110
255 No function
000 No function
001
255 Selects HDMI input; Dimmer 1–100%
000 No function
001
255 Selects DVI input; Dimmer 1–100%
000 No function
001
255 Selects SDI input; Dimmer 1–100%
16
VIP Drive 43s User Manual Rev. 1
Page 21
OPERATION
Art-Net™ Values (cont.)
CHANNEL FUNCTION VALUE PERCENT/SETTING
13 Red Balance 000 255 0–100% 14 Green Balance 000 15 Blue Balance 000 16 Input 1 Horizontal Offset 000
17
Input 1 Fine Horizontal
Offset 18 Input 1 Vertical Offset 000 19 Input 1 Fine Vertical Offset 000 20 Input 1 Horizontal Scaling 000
21
Input 1 Fine Horizontal
Scaling 22 Input 1 Vertical Scaling 000 23 Input 1 Fine Vertical Scaling 000 24 Input 1 Center Zoom 000 25 Input 1 Fine Center Zoom 000 26 Input 1 Left/Right Zoom 000
27
Input 1 Fine Left/Right
Zoom 28 Input 1 Top/Bottom Zoom 000
29
Input 1 Fine Top/Bottom
Zoom 30 Input 2 Horizontal Offset 000
31
Input 2 Fine Horizontal
Offset 32 Input 2 Vertical Offset 000 33 Input 2 Fine Vertical Offset 000 34 Input 2 Horizontal Scaling 000
35
Input 2 Fine Horizontal
Scaling 36 Input 2 Vertical Scaling 000 37 Input 2 Fine Vertical Scaling 000 38 Input 2 Center Zoom 000 39 Input 2 Fine Center Zoom 000 40 Input 2 Left/Right Zoom 000
41
Input 2 Fine Left/Right
Zoom 42 Input 2 Top/Bottom Zoom 000
43
Input 2 Fine Top/Bottom
Zoom 44 Port 1/2 Horizontal Offset 000
45
Port 1/2 Fine Horizontal
Offset 46 Port 1/2 Vertical Offset 000 47 Port 1/2 Fine Vertical Offset 00 0 48 Port 3/4 Horizontal Offset 000
49
Port 3/4 Fine Horizontal
Offset 50 Port 3/4 Vertical Offset 000
255 0–100% 255 0–100% 255 0–100%, left to right
000
255 0–100%, left to right 255 0–100%, top to bottom
255 0–100%, top to bottom 255 0–100%, narrow to wide
000
255 0–100%, narrow to wide 255 0–100%, short to tall
255 0–100%, short to tall 255 0–100%, far to close 255 0–100%, far to close 255 0–100%, far to close
000
255 0–100%, far to close 255 0–100%, far to close
000
255 0–100%, far to close 255 0–100%, left to right
000
255 0–100%, left to right 255 0–100%, top to bottom
255 0–100%, top to bottom 255 0–100%, narrow to wide
000
255 0–100%, narrow to wide 255 0–100%, short to tall
255 0–100%, short to tall 255 0–100%, far to close 255 0–100%, far to close 255 0–100%, far to close
000
255 0–100%, far to close 255 0–100%, far to close
000
255 0–100%, far to close 255 0–100%, left to right
000
255 0–100%, left to right 255 0–100%, top to bottom
255 0–100%, top to bottom 255 0–100%, left to right
000
255 0–100%, left to right 255 0–100%, top to bottom
VIP Drive 43s User Manual Rev. 1
17
Page 22
Art-Net™ Values (cont.)
CHANNEL FUNCTION VALUE PERCENT/SETTING
51 Port 3/4 Fine Vertical Offset 00 0  255 0–100%, top to bottom 52 Port 1 Horizontal Offset 000
53
Port 1 Fine Horizontal
Offset 54 Port 1 Vertical Offset 000 55 Port 1 Fine Vertical Offset 000 56 Port 2 Horizontal Offset 000
57
Port 2 Fine Horizontal
Offset 58 Port 2 Vertical Offset 000 59 Port 2 Fine Vertical Offset 000 60 Port 3 Horizontal Offset 000
61
Port 3 Fine Horizontal
Offset 62 Port 3 Vertical Offset 000 63 Port 3 Fine Vertical Offset 000 64 Port 4 Horizontal Offset 000
65
Port 4 Fine Horizontal
Offset 66 Port 4 Vertical Offset 000 67 Port 4 Fine Vertical Offset 000
68
69
70
71
72
73
Port 1 Horizontal Panel
Quantity
Port 1 Vertical Panel
Quantity
Port 1 Horizontal Pixels Per
Panel
Port 1 Fine Horizontal
Pixels Per Panel
Port 1 Vertical Pixels Per
Panel
Port 1 Fine Vertical Pixels
Per Panel
255 0–100%, left to right
000
255 0–100%, left to right 255 0–100%, top to bottom
255 0–100%, top to bottom 255 0–100%, left to right
000
255 0–100%, left to right 255 0–100%, top to bottom
255 0–100%, top to bottom 255 0–100%, left to right
000
255 0–100%, left to right 255 0–100%, top to bottom
255 0–100%, top to bottom 255 0–100%, left to right
000
255 0–100%, left to right 255 0–100%, top to bottom
255 0–100%, top to bottom
000
255 1 to maximum (Ch. 8 must be 190–195)
000
255 1 to maximum (Ch. 8 must be 190–195)
000
255 1 to 900 (Ch. 8 must be 190–195)
000
255 1 to 99 (Ch. 8 must be 190–195)
000
255 1 to 900 (Ch. 8 must be 190–195)
000
255 1 to 99 (Ch. 8 must be 190–195)
000
009 No function 019
010
OPERATION
18
74
Port 1 Data Flow (Ch. 8 must
be 190–195)
029
020
039
030
049
040
059
050
069
060
079
070
089
080
255 Reserved for future use
090
VIP Drive 43s User Manual Rev. 1
Page 23
OPERATION
Art-Net™ Values (cont.)
CHANNEL FUNCTION VALUE PERCENT/SETTING
75
76
77
78
79
80
81
Port 2 Horizontal Panel
Quantity
Port 2 Vertical Panel
Quantity
Port 2 Horizontal Pixels Per
Panel
Port 2 Fine Horizontal
Pixels Per Panel
Port 2 Vertical Pixels Per
Panel
Port 2 Fine Vertical Pixels
Per Panel
Port 2 Data Flow (Ch. 8 must
be 190–195)
000 255 1 to maximum (Ch. 8 must be 190–195)
000
255 1 to maximum (Ch. 8 must be 190–195)
000
255 1 to 900 (Ch. 8 must be 190–195)
000
255 1 to 99 (Ch. 8 must be 190–195)
000
255 1 to 900 (Ch. 8 must be 190–195)
000
255 1 to 99 (Ch. 8 must be 190–195)
000
009 No function 019
010
029
020
039
030
049
040
059
050
82
83
84
85
86
87
Port 3 Horizontal Panel
Quantity
Port 3 Vertical Panel
Quantity
Port 3 Horizontal Pixels Per
Panel
Port 3 Fine Horizontal
Pixels Per Panel
Port 3 Vertical Pixels Per
Panel
Port 3 Fine Vertical Pixels
Per Panel
069
060
079
070
089
080
255 Reserved for future use
090 000
255 1 to maximum (Ch. 8 must be 190–195)
000
255 1 to maximum (Ch. 8 must be 190–195)
000
255 1 to 900 (Ch. 8 must be 190–195)
000
255 1 to 99 (Ch. 8 must be 190–195)
000
255 1 to 900 (Ch. 8 must be 190–195)
000
255 1 to 99 (Ch. 8 must be 190–195)
VIP Drive 43s User Manual Rev. 1
19
Page 24
Art-Net™ Values (cont.)
CHANNEL FUNCTION VALUE PERCENT/SETTING
000
009 No function 019
010
029
020 030
039 049
88
89
90
91
92
93
94
Port 3 Data Flow (Ch. 8 must
be 190–195)
Port 4 Horizontal Panel
Quantity
Port 4 Vertical Panel
Quantity
Port 4 Horizontal Pixels Per
Panel
Port 4 Fine Horizontal
Pixels Per Panel
Port 4 Vertical Pixels Per
Panel
Port 4 Fine Vertical Pixels
Per Panel
040
059
050
069
060
079
070
089
080
255 Reserved for future use
090 000
255 1 to maximum (Ch. 8 must be 190–195)
000
255 1 to maximum (Ch. 8 must be 190–195)
000
255 1 to 900 (Ch. 8 must be 190–195)
000
255 1 to 99 (Ch. 8 must be 190–195)
000
255 1 to 900 (Ch. 8 must be 190–195) 255 1 to 99 (Ch. 8 must be 190–195)
000 000
009 No function 019
010
OPERATION
029
020
039
030
049
95
Port 4 Data Flow (Ch. 8 must
be 190–195)
040
059
050
069
060
079
070
089
080
255 Reserved for future use
090

Backup

The VIP Drive 43s can save up to 10 different settings configurations to be recalled at any time or loaded onto another VIP Drive 43s.
To access the Backup menu:
1. Press <MENU> to access the menu.
2. Turn the <SCROLL/ENTER> knob until Backup is selected.
3. Press the <SCROLL/ENTER> knob.
20
VIP Drive 43s User Manual Rev. 1
Page 25
OPERATION
Save Configuration
To save the current settings configuration so it can be recalled at any time:
1. Access the Backup
2. Turn the <SCROLL/ENTER> knob until Save Setup is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counter-clockwise to select from Save1–10.
5. Press the <SCROLL/ENTER> knob to save the current configuration to the selected save file.
6. Press <MENU> to exit.
Load Configuration
To load a previously saved configuration:
1. Access the Backup
2. Turn the <SCROLL/ENTER> knob until Load Setup is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counter-clockwise to select from Save1–10.
5. Press the <SCROLL/ENTER> knob to load the selected save file into the product’s settings.
6. Press <MENU> to exit.
Load One Configuration from USB
To save the current settings configuration from a USB-connected VIP Drive 43s:
1. Access the Backup
2. Turn the <SCROLL/ENTER> knob until Load Single From USB is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counter-clockwise to select from Save1–10.
5. Press the <SCROLL/ENTER> knob to copy the connected product’s settings into the selected save file.
6. Press <MENU> to exit.
Load All from USB
To copy all save files from a USB-connected VIP Drive 43s:
1. Access the Backup
2. Turn the <SCROLL/ENTER> knob until Load all from USB is selected.
3. Press the <SCROLL/ENTER> knob. The display will show All as the only option.
4. Press the <SCROLL/ENTER> knob to copy all of the connected product’s save files.
5. Press <MENU> to exit.
Save All to USB
To copy all save files to a USB-connected VIP Drive 43s:
1. Access the Backup
2. Turn the <SCROLL/ENTER> knob until Save all to USB is selected.
3. Press the <SCROLL/ENTER> knob. The display will show All as the only option.
4. Press the <SCROLL/ENTER> knob to copy all save files to the connected product.
5. Press <MENU> to exit.

Transition

The Transition settings control deinterlacing and image enhancing, and determine the way the VIP Drive 43s will transition from one input source to another.
To access the Transition menu:
1. Press <MENU> to access the menu.
2. Turn the <SCROLL/ENTER> knob until Transition is selected.
3. Press the <SCROLL/ENTER> knob.
Deinterlacing
Deinterlacing is the process of converting an interlaced video signal (two fields of images per frame, traditionally for analog systems) into a progressive signal (a single image per frame). This option can be enabled for interlaced signals, or disabled for progressive signals.
1. Access the Transition
2. Turn the <SCROLL/ENTER> knob until Deinterlace is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select Off or On.
5. Press the <SCROLL/ENTER> knob.
menu.
menu.
menu.
menu.
menu.
menu.
VIP Drive 43s User Manual Rev. 1
21
Page 26
OPERATION
Image Enhance
The Image Enhance setting corrects for data loss or corrup tion, often due to cables (damage d, poor quality or too long) or radio frequency interference. With Image Enhance enabled, the VIP Drive 43s will detect any errors and correct them before the signal reaches the connected panel assembly.
1. Access the Transition
2. Turn the <SCROLL/ENTER> knob until Image Enhance is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select Off or On.
5. Press the <SCROLL/ENTER> knob.
Fade Type
The Fade Type setting determines the way the VIP Drive 43s will transition from one image source to another.
1. Access the Transition
2. Turn the <SCROLL/ENTER> knob until Fade Type is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select from:
Dissolve (The first image fades into the second)
Cut (No transition effect)
Wipe Square In (The second image wipes in from all sides, covering the first)
Wipe Square Ou (The first im ag e wip es ou t fro m the center, revealing the second)
Wipe T_L In (The second image wipes in from the top left, covering the first)
Wipe T_L (The first image wipes out to the top left, revealing the second)
Wipe T_R In (The second image wipes in from the top right, covering the first)
Wipe T_R (The first image wipes out to the top right, revealing the second)
Wipe B_L In (The second image wipes in from the bottom left, covering the first)
Wipe B_L (The first image wipes out to the bottom left, revealing the second)
Wipe B_R In (The second image wipes in from the bottom right, covering the first)
Wipe B_R (The first image wipes out to the bottom right, revealing the second)
Wipe Left In (The second image wipes in from the left, covering the first)
Wipe Left (The first image wipes out to the left, revealing the second)
Wipe Right In (The second image wipes in from the right, covering the first)
Wipe Right (The first image wipes out to the right, revealing the second)
Wipe Top In (The second image wipes in from the top, covering the first)
Wipe Top (The first image wipes out to the top, revealing the second)
Wipe Bottom In (The second image wipes in from the bottom, covering the first)
or
Wipe Bottom (The first image wipes out to the bottom, revealing the second)
5. Press the <SCROLL/ENTER> knob.
Fade Time
The Fade Time setting determines the delay between selecting an input source and the transition.
1. Access the Transition
2. Turn the <SCROLL/ENTER> knob until Fade is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select from 0.0s, 0.5s, 1.0s,
1.5s, 2.0s, 2.5s, or 3.0s.
5. Press the <SCROLL/ENTER> knob.
menu.
menu.
menu.
22
VIP Drive 43s User Manual Rev. 1
Page 27
OPERATION

Test Pattern

The Test Pattern function sends one of 20 patterns to the connected panel asse mbly to test the panels, the connections, and the mapping.
To access the Test Pattern menu:
1. Press <MENU> to access the menu.
2. Turn the <SCROLL/ENTER> knob until Test Pattern is selected.
3. Press the <SCROLL/ENTER> knob.
To enable or disable the Test Pattern function:
1. Access the Test Pattern
2. Turn the <SCROLL/ENTER> knob until Test Pattern is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select Off or On.
5. Press the <SCROLL/ENTER> knob.
Test Pattern Mode
To select which pattern is sent to the connected panel assembly:
1. Access the Test Pattern
2. Turn the <SCROLL/ENTER> knob until Mode is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select from 1–20.
5. Press the <SCROLL/ENTER> knob.
Some panel configurations may be too small to view Test Patterns 3–10 and 13 properly.
menu.
menu.
Test Pattern Mode 19
With Test Pattern Mode 19 selected, after pressing the <SCROLL/ENTER> knob, 3 new options will appear. Test Pattern Mode 19 will only output to the connected panels after one of these options is selected.
After selecting Test Pattern Mode 19:
1. Turn the <SCROLL/ENTER> knob until Red, Green, or Blue is selected.
2. Press the <SCROLL/ENTER> knob.
3. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the color value, from 0–255.
4. Press the <SCROLL/ENTER> knob.
Test Pattern Mode 20
With Test Pattern Mode 20 selected, after pressing the <SCROLL/ENTER> knob, 3 new options will appear.
Horizontal Gradient Steps
1. Turn the <SCROLL/ENTER> knob until HOR STEP is selected.
2. Press the <SCROLL/ENTER> knob.
3. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease
the number of horizontal steps in the grad ie nt, from 2, 4, 8, 16, 32, or 64.
4. Press the <SCROLL/ENTER> knob.
Vertical Gradient Steps
1. Turn the <SCROLL/ENTER> knob until VER STEP is selected.
2. Press the <SCROLL/ENTER> knob.
3. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease
the number of vertical steps in the gradient, from 0, 4, 8, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, or 64.
4. Press the <SCROLL/ENTER> knob.
•Color
1. Turn the <SCROLL/ENTER> knob until VER STEP is selected.
2. Press the <SCROLL/ENTER> knob.
3. Turn the <SCROLL/ENTER> knob to select the color of the gradient, from Red, Green,
Blue, or White.
4. Press the <SCROLL/ENTER> knob.
VIP Drive 43s User Manual Rev. 1
23
Page 28
OPERATION
Auto Switch
The Auto Switch function cycles through all of the test pattern modes at an adjustable rate.
1. Access the Test Pattern
2. Turn the <SCROLL/ENTER> knob until Auto Switch is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select from Off, or 1–10s.
5. Press the <SCROLL/ENTER> knob.

Picture In Picture

The PIP (Picture In Picture) function allows 2 input sources to be displayed on the connected panel assembly at once.
To access the PIP menu:
1. Press <MENU> to access the menu.
2. Turn the <SCROLL/ENTER> knob until PIP is selected.
3. Press the <SCROLL/ENTER> knob.
To enable or disable PIP:
1. Access the PIP
2. Turn the <SCROLL/ENTER> knob until PIP is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select Off or On.
5. Press the <SCROLL/ENTER> knob.
Input Selection
There are two methods of selecting the inputs in PIP mode. For button options, see Input Mode. To select both inputs through the menu:
1. Access the PIP
2. Turn the <SCROLL/ENTER> knob until Input is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select from
Default (Input settings will be unchanged),
HDMI/DVI (Input 1: DVI, Input 2: HDMI)
HDMI/SDI (Input 1: SDI, Input 2: HDMI)
SDI/DVI (Input 1: DVI, Input 2: SDI)
SDI/HDMI (Input 1: HDMI, Input 2: SDI)
DVI/HDMI (Input 1: HDMI, Input 2: DVI)
or
DVI/SDI (Input 1: SDI, Input 2: DVI)
5. Press the <SCROLL/ENTER> knob.
Position
The position setting determines where on the connected panel assembly the input designated as PIP will be displayed.
1. Access the PIP
2. Turn the <SCROLL/ENTER> knob until Position is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select from
L+T (Top left of the panel assembly),
R+T (Top right of the panel assembly),
L+B (Bottom left of the panel assemb ly),
R+B (Bottom right of the panel assembly),
Cent (Center of the panel assembly),
L+R (One input on the left, the other on the right of the panel assembly),
or
T+B (One input on the top, the other on the bottom of the panel assembly)
5. Press the <SCROLL/ENTER> knob.
menu.
menu.
menu.
menu.
24
VIP Drive 43s User Manual Rev. 1
Page 29
OPERATION
Input Mode
Selecting INPUT 1 or INPUT 2 under PIP de termines which input can be scaled, as well as which input can be changed by pressing one of the buttons on the front panel.
1. Access the PIP
2. Turn the <SCROLL/ENTER> knob until Select is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select INPUT 1 or INPUT 2.
5. Press the <SCROLL/ENTER> knob.
Press <HDMI>, <SDI>, or <DVI> to change the source of the selected input.
Swap Inputs
The swap function switches which input is in the foreground and which is in the background.
1. Access the PIP
2. Turn the <SCROLL/ENTER> knob until Swap is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select Off (INPUT 1 is in the foreground) or On (INPUT 2 is in the foreground).
5. Press the <SCROLL/ENTER> knob.

Display Brightness

To alter the brightness of the menu display:
1. Press <MENU> to access the menu.
2. Turn the <SCROLL/ENTER> knob until OLED Brightness is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the display brightness, from 1–15.
5. Press the <SCROLL/ENTER> knob.

Video Input

The Video Input settings determine the method the VIP Drive 43s communicates with the video sources. The product can detect the format of an incoming signal automatically, or can be overwritten with a specific format.
1. Press <MENU> to access the menu.
2. Turn the <SCROLL/ENTER> knob until Video Input is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select from HDMI, DVI, or HD-SDI.
5. Press the <SCROLL/ENTER> knob.
6. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select either Auto or Overwrite (not available for HD-SDI).
7. Press the <SCROLL/ENTER> knob. If Auto was selected, the format of the input signal will be displayed. If Overwrite was selected, continue.
8. The display will read EDID Source. Press the <SCROLL/ENTER> knob.
9. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select from RGB DVI, RGB HDMI, PREVIEW DVI, FOLLOW, or CUSTOM.
10. Press the <SCROLL/ENTER> knob.
11. For:
RGB DVI (for an RGB DVI signal over DVI or HDMI), RGB HDMI (only available for HDMI),
PREVIEW DVI (to copy the format of being output through the PREVIEW OUT port), or FOLLOW (reserved for future use), press the <SCROLL/ENTER> knob.
CUSTOM, set the resolution and refresh rate:
a. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or b. Press the <SCROLL/ENTER> knob.
c. Repeat with each digit until the resolution and refresh rate are set as desired.
menu.
menu.
decrease the value of the firs t digit. Select carefully.
VIP Drive 43s User Manual Rev. 1
25
Page 30
OPERATION

Temperature

The Temperature option displays the current product temperature in either Celsius or Fahrenheit.
1. Press <MENU> to access the menu.
2. Turn the <SCROLL/ENTER> knob until Temperature is selected.
3. Press the <SCROLL/ENTER> knob. The current product temperature will be displayed.
To select the unit of temperature to display:
4. Press the <SCROLL/ENTER> knob again.
5. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select from Celsius or Fahrenheit.
6. Press the <SCROLL/ENTER> knob.

Advanced

The Advanced menu includes button controls, port assignment, a factory reset option, and preset output formats.
To access the Advanced menu:
1. Press <MENU> to access the menu.
2. Turn the <SCROLL/ENTER> knob until Advanced is selected.
3. Press the <SCROLL/ENTER> knob.
Firmware Version
To view the firmware version of the product, access the Advanced menu. The first line will display the firmware version.
Double-tap To Switch
The Double-tap To Switch option determines how many button presses are required to switch input sources.
1. Access the Advanced
2. Turn the <SCROLL/ENTER> knob until Double-tap To Switch is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select Off (One press will switch input sources) or On (Button must be pressed twice to switch input sources).
5. Press the <SCROLL/ENTER> knob.
Preview Output
The Preview Output setting determines whether the pr eview display shows the video signal befo re or after scaling.
1. Access the Advanced
2. Turn the <SCROLL/ENTER> knob until Preview Output is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select Pre (Outputs the unscaled video signal) or Post (Outputs the scaled video signal).
5. Press the <SCROLL/ENTER> knob.
Preview DVI Port
The Preview DVI Port setting determines whether the PREVIEW OUT port outputs a preview signal to a monitor, or a full video signal to another product.
1. Access the Advanced
2. Turn the <SCROLL/ENTER> knob until Preview DVI Port is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select Preview or Program.
5. Press the <SCROLL/ENTER> knob.
menu.
menu.
menu.
26
With Program selected, the signal from the PREVIEW OUT port is unscaled.
VIP Drive 43s User Manual Rev. 1
Page 31
OPERATION
Factory Reset
To reset the product to factory default settings:
1. Access the Advanced
2. Turn the <SCROLL/ENTER> knob until Factory Reset is selected.
3. Press the <SCROLL/ENTER> knob.
4. Press the <SCROLL/ENTER> knob to confirm, or <MENU> to cancel.
Do not remove the product from power until it has finished performing the factory reset.
Customized Button
Aside from their default functions, the <SCALE> and <MAP> buttons can be assigned to either black out or freeze the output.
1. Access the Advanced
2. Turn the <SCROLL/ENTER> knob until Customized Button is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select Scale or Map.
5. Press the <SCROLL/ENTER> knob.
6. For:
Scale, turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select from
Scale (accesses the Scale output).
Map, turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select from Map
(accesses the Map menu), Blackout (Blacks out the output), or Freeze (Freezes the ou tput).
7. Press the <SCROLL/ENTER> knob.
Output Format
To select a pre-defined output format:
1. Access the Advanced
2. Turn the <SCROLL/ENTER> knob until Output Format is selected.
3. Press the <SCROLL/ENTER> knob.
4. Standard will be selected. Press the <SCROLL/ENTER> knob again.
5. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select from 800x600@60,
1024x768@60, 1024x768@75, 1280x720@60, 1280x720@50, 1280x768@60, 1280x800@60, 1280x1024@60, 1360x768@60, 1366x768@60, 1400x1050@60, 1440x900@60, 1600x1200@60, 1680x1050@60, 1920x1080@60, 1920x1080@50, 1920x1200@60, 2048x1152@60, 2560x812@60, or 2560x816@60.
6. Press the <SCROLL/ENTER> knob.

Scale

The Scale settings determine the size of the video output as well as a the position of the output on the connected panel assembly. In PIP mode, the Input Mode determines which input is being scaled.
To access the Scale menu, press <SCALE> (if it is set to default), or:
1. Press <MENU> to access the menu.
2. Turn the <SCROLL/ENTER> knob until Scale is selected.
3. Press the <SCROLL/ENTER> knob.
Horizontal Size
To set the horizontal size of the product’s output:
1. Access the Scale
2. Turn the <SCROLL/ENTER> knob until Scale is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob until H Size is selected.
5. Press the <SCROLL/ENTER> knob.
6. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the value, from 2–_ _ _ _ (This value is determined by the Video Input
7. Press the <SCROLL/ENTER> knob.
menu.
menu.
menu), Blackout (Blacks out the output), or Freeze (Freezes the
menu.
menu.
).
VIP Drive 43s User Manual Rev. 1
27
Page 32
OPERATION
Vertical Size
To set the vertical size of the product’s output:
1. Access the Scale
2. Turn the <SCROLL/ENTER> knob until Scale is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob until V Size is selected.
5. Press the <SCROLL/ENTER> knob.
6. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the value, from 2–_ _ _ _ (This value is determined by the Video Input
7. Press the <SCROLL/ENTER> knob.
Horizontal and Vertical Scale
To set both the horizontal and vertical sizes of the product’s output simultaneously:
1. Access the Scale
2. Turn the <SCROLL/ENTER> knob until Scale is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob until H/V Size is selected.
5. Press the <SCROLL/ENTER> knob.
6. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the value, from 2–_ _ _ _ (This value is determined by the Video Input
7. Press the <SCROLL/ENTER> knob. The H Size and V Size fields will automatically populate in proportion.
Horizontal Offset
The Horizontal Offset setting determines how far to the right on the connected panel assembly the output of this VIP Drive 43s begins.
1. Access the Scale
2. Turn the <SCROLL/ENTER> knob until Scale is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob until H Position is selected.
5. Press the <SCROLL/ENTER> knob.
6. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the value, from 0–_ _ _ _ (This value is determined by the difference between the Video Input the Horizontal Size
7. Press the <SCROLL/ENTER> knob.
Vertical Offset
The Vertical Offset setting determines how far down on the connected panel assembly the output of this VIP Drive 43s begins.
1. Access the Scale
2. Turn the <SCROLL/ENTER> knob until Scale is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob until V Position is selected.
5. Press the <SCROLL/ENTER> knob.
6. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the value, from 0–_ _ _ _ (This value is determined by the difference between the Video Input the Vertical Size
7. Press the <SCROLL/ENTER> knob.
Auto Scale
The Auto Scale function sets the scaling based on the mapping, the connected panel assembly, and the
Video Input
1. Access the Scale
2. Turn the <SCROLL/ENTER> knob until Scale is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob until Auto Scale is selected.
5. Press the <SCROLL/ENTER> knob.
6. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select No or Yes.
7. Press the <SCROLL/ENTER> knob.
.
menu.
).
menu.
).
menu.
and
).
menu.
and
).
menu.
28
VIP Drive 43s User Manual Rev. 1
Page 33
OPERATION
Reset Scaling
To reset the scaling settings to default:
1. Access the Scale
2. Turn the <SCROLL/ENTER> knob until Scale is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob until Reset is selected.
5. Press the <SCROLL/ENTER> knob.
Zoom/Crop Image
The Zoom/Crop Image menu provides the zoom functions for cropping the video output. To access the Zoom/Crop Image menu:
1. Access the Scale
2. Turn the <SCROLL/ENTER> knob until Advanced is selected.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob until Zoom/Crop Image is selected.
5. Press the <SCROLL/ENTER> knob.
There are 7 different zoom values that can be set to pre cision. Each one str etches the video ou tput in 1, 2, or 4 directions.
1. Access the Zoom/Crop Image
2. Turn the <SCROLL/ENTER> knob to select from Top (1), Bottom (1), Top/Bottom (2), Left (1), Right (1), Left/Right (2), or Center (4).
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the zoom, from 0–_ _ _ _ (The maximum values are determined by the scale and the other zoom values. Editing these values may cause changes to the other zoom values).
5. Press the <SCROLL/ENTER> knob.
6. Repeat steps 2-5 until the zoom is set as desired.
Reset Zoom
To reset the zoom values to 0:
1. Access the Zoom/Crop Image
2. Turn the <SCROLL/ENTER> knob to select Reset.
3. Press the <SCROLL/ENTER> knob.
Map
The Map settings define the arrangement and number of pa nels for each port, a nd well as semi-globa l and individual offsets.
To access the Map menu, press <MAP> (if it is set to default) or:
1. Press <MENU> to access the menu.
2. Turn the <SCROLL/ENTER> knob until Map is selected.
3. Press the <SCROLL/ENTER> knob.
Offset Settings
The Offset Settings determine the semi-global positions of ports 1 and 2 together and ports 2 and 3 together on the connected panel assembly.
1. Access the Map
2. Turn the <SCROLL/ENTER> knob to select Offset Settings.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select from Port 1/2 Offs et
X (ports 1 and 2 horizontal position), Port 1/2 Offset Y (ports 1 and 2 vertical position), Port 3/4 Offset X (ports 3 and 4 horizontal position), or Port 3/4 Offset Y (ports 3 and 4 vertical position).
5. Press the <SCROLL/ENTER> knob.
6. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the value, from 0–65535.
7. Press the <SCROLL/ENTER> knob.
8. Repeat steps 4-7 until the offsets are set as desired.
menu.
menu.
menu.
menu.
menu.
VIP Drive 43s User Manual Rev. 1
29
Page 34
OPERATION
Position Settings
The Position Settings determine the individual offsets of each port.
1. Access the Map
2. Turn the <SCROLL/ENTER> knob to select Position Settings.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to select from Port 1 X (port 1 horizontal offset), Port 1 Y (port 1 vertical of fset), Port 2 X (port 2 horizontal of fset), Port 2 Y (por t 2 vertical offset), Port 3 X (port 1 horizontal offset), Port 3 Y (p ort 3 vertical offset), Port 4 X (port 4 horizontal offset), or Port 4 Y (port 4 vertical offset).
5. Press the <SCROLL/ENTER> knob.
6. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the value, from 0–65535.
7. Press the <SCROLL/ENTER> knob.
8. Repeat steps 4-7 until the positions are set as desired.
Port Tutorial
The Port Tutorial settings provide 2 methods of mapping the size and number of pixels in the connected panel assembly to the VIP Drive 43s.
To access the Port Tutorial menu:
1. Access the Map
2. Turn the <SCROLL/ENTER> knob to select Port Tutorial.
3. Press the <SCROLL/ENTER> knob.
Auto Port Tutorial
Selecting Auto under Port Tutorial will trigger the VIP Drive 43s to detect the panels connected to the selected port.
1. Access the Port Tutorial
2. Turn the <SCROLL/ENTER> knob to select from Port 1–4.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob to select Auto.
5. Press the <SCROLL/ENTER> knob.
Manual Port Tutorial
Selecting Manual under Port Tutorial will allow the arrangement of panels and pixels per panel to be entered precisely.
1. Access the Port Tutorial
2. Turn the <SCROLL/ENTER> knob to select from Port 1–4.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob to select Manual.
5. Press the <SCROLL/ENTER> knob.
6. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the horizontal number of panels, from 1–255.
7. Press the <SCROLL/ENTER> knob.
8. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the vertical number of panels, from 1–255.
9. Press the <SCROLL/ENTER> knob.
10. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the horizontal number of pixels, from 1–999.
11. Press the <SCROLL/ENTER> knob.
12. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the vertical number of pixels, from 1–999.
13. Press the <SCROLL/ENTER> knob. The total number of pixels will auto-populate.
menu.
menu.
menu.
menu.
30
VIP Drive 43s User Manual Rev. 1
Page 35
OPERATION
Set Width
The Set Width option determines the total width in pixels of the connected panel assembly.
1. Access the Map
2. Turn the <SCROLL/ENTER> knob to select Set Width.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob to select H Size .
5. Press the <SCROLL/ENTER> knob.
6. Turn the <SCROLL/ENTER> knob to select from Auto (populates width from map settings) or Manual (enter width manually).
7. Press the <SCROLL/ENTER> knob.
8. If Auto, go to step 10. If Manual, turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the pixel width, from 2–_ _ _ _ (this value determined by the Video Input
9. Press the <SCROLL/ENTER> knob.
10. Turn the <SCROLL/ENTER> knob to select Set Width.
11. Press the <SCROLL/ENTER> knob.
menu.
).
For Set Width to function correctly, the minimum Wall Size
(WxH) is 3x2.
Test Grid
The Test Grid function sends a customizable grid to the connected pan el assembly, with a single panel at a time lit up to test the mapping.
To access the Test Grid menu:
1. Access the Map
2. Turn the <SCROLL/ENTER> knob to select Test Grid.
3. Press the <SCROLL/ENTER> knob.
To enable or disable the Test Grid:
1. Access the Test Grid
2. Turn the <SCROLL/ENTER> knob to select Test Grid.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob to select from Off or On.
5. Press the <SCROLL/ENTER> knob.
menu.
menu.
Test Grid Port
To select which port to test:
1. Access the Test Grid
2. Turn the <SCROLL/ENTER> knob to select Port.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob to select from Port 1–4.
5. Press the <SCROLL/ENTER> knob.
menu.
Test Grid Color
To select the color of the Test Grid:
1. Access the Test Grid
2. Turn the <SCROLL/ENTER> knob to select Grid Color.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob to select from Red, Green, or Yellow.
5. Press the <SCROLL/ENTER> knob.
menu.
Test Grid Type
There are 4 available types of test grid.
1. Access the Test Grid
2. Turn the <SCROLL/ENTER> knob to select Type.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob to select from Cross, Row, Column, or Rectangle.
5. Press the <SCROLL/ENTER> knob.
menu.
VIP Drive 43s User Manual Rev. 1
31
Page 36
OPERATION
Test Grid Pattern Motion
The lit panel of the Test Grid can move from panel to panel automatically or manually.
1. Access the Test Grid
2. Turn the <SCROLL/ENTER> knob to select Test Patterns.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob to select from Auto Move or Manual.
5. Press the <SCROLL/ENTER> knob.
6. For Manual, turn the <SCROLL/ENTER> knob to select from H Position (horizontal) or V Position (vertical).
7. Press the <SCROLL/ENTER> knob.
8. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the value, from 1–_ _ _ (this value determined by the number of panels mapped to the selected port).
9. Repeat steps 5-8 to manually test that all panels were mapped correctly.
Test Grid Speed
To set the speed of the Auto Move:
1. Access the Test Grid
2. Turn the <SCROLL/ENTER> knob to select Moving.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the speed, from 1–255 (fast to slow).
5. Press the <SCROLL/ENTER> knob.
Test Grid Pattern Color
To select the color of the panel of the lit panel in the test grid:
1. Access the Test Grid
2. Turn the <SCROLL/ENTER> knob to select Patterns Color. The default setting is White.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob to select from Red, Green, Blue, or Custom.
5. Press the <SCROLL/ENTER> knob.
6. If Custom, turn the <SCROLL/ENTER> knob to select from Red, Green, or Blue.
7. Press the <SCROLL/ENTER> knob.
8. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the color value, from 0–255.
9. Press the <SCROLL/ENTER> knob.
10. Repeat steps 6-9 until the lit panel is the desired color.
Mapping by Port
The rest of the options under Map determine the mapping for each port separately. Each of the following options appears 4 times, once for each port.
Wall Size
The Wall Size setting determines the number and arrangement of panels by width and height for the selected port.
1. Access the Map
2. Turn the <SCROLL/ENTER> knob to select Wall Size WxH under Port 1, Port 2, Port 3, or Port
4.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the horizontal quantity, from 1–255.
5. Press the <SCROLL/ENTER> knob.
6. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the vertical quantity, from 1–255.
7. Press the <SCROLL/ENTER> knob.
menu.
menu.
menu.
menu.
32
VIP Drive 43s User Manual Rev. 1
Page 37
OPERATION
Pixels per Panel
The Panel Pixel setting determines the number and arrangement of pixels per panel by width and height for the selected port.
1. Access the Map
2. Turn the <SCROLL/ENTER> knob to select Panel Pixel WxH under Port 1, Port 2, Port 3, or Port 4.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the horizontal quantity of pixels per panel, from 1–999.
5. Press the <SCROLL/ENTER> knob.
6. Turn the <SCROLL/ENTER> knob clockwise or counterclockwise to increase or decrease the vertical quantity of pixels per panel, from 1–999.
7. Press the <SCROLL/ENTER> knob.
Connection Type
The Connection Type setting determines the path of data flow for the selected port.
1. Access the Map
2. Turn the <SCROLL/ENTER> knob to select Connection Type under Port 1, Port 2, Port 3, or Port 4.
3. Press the <SCROLL/ENTER> knob.
4. Turn the <SCROLL/ENTER> knob to select from one of the following icons:
ICON MEANING ICON MEANING
Starts at the top left, goes all the way right, down one, all the way left, down one, and repeats.
Starts at the top right, goes all the way left, down one, all the way right, down one, and repeats.
Starts at the bottom left, goes all the way right, up one, all the way left, up one, and repeats.
Starts at the bottom right, goes all the way left, up one, all the way right, up one, and repeats.
menu.
menu.
Starts at the top left, goes all the way down, right one, all the way up, right one, and repeats.
Starts at the bottom left, goes all the way up, right one, all the way down, right one, and repeats.
Starts at the top right, goes all the way down, left one, all the way up, left one, and repeats.
Starts on the bottom right, goes all the up, left one, all the way down, left one, and repeats.
5. Press the <SCROLL/ENTER> knob.
Save To Port
To save the configuration of the map settings to each port:
1. Access the Map
2. Turn the <SCROLL/ENTER> knob to select Save To Port under Port 1, Port 2, Port 3, or Port 4.
3. Press the <SCROLL/ENTER> knob.
menu.
Reset
To reset all of the mapping settings for each port:
1. Access the Map
2. Turn the <SCROLL/ENTER> knob to select Reset.
3. Press the <SCROLL/ENTER> knob.
menu.
VIP Drive 43s User Manual Rev. 1
33
Page 38
TECHNICAL INFORMATION

5. TECHNICAL INFORMATION

Product Maintenance

To maintain optimum performance and minimize wear, clean this product frequently. Usage and environment are contributing factors in determining the cleaning frequency.
Clean this product at least twice a month. Dust build-up reduces performance and can cause overheating. This can lead to reduced life and increased mechanical wear.
To clean the product:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuu m (o r dr y com p re sse d air) an d a soft brush to remove dust collected on the external vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl alcohol.
5. Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently po lish the tran sp ar en t su rfa ce s un til the y ar e fre e of haz e an d lint .
Always dry the transparent surfaces carefully after cleaning them.
34
VIP Drive 43s User Manual Rev. 1
Page 39
TECHNICAL SPECIFICATIONS

6. TECHNICAL SPECIFICATIONS

Dimensions and Weight
LENGTH WIDTH HEIGHT WEIGHT
19 in (483 mm) 16 in (407 mm) 1.7 in (44 mm) 7.2 lb (3.27 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
POWER SUPPLY TYPE RANGE VOLTAGE SELECTION
Switching (internal) 100 to 240 VAC, 50/60 Hz Auto-ranging
PARAMETER 120 V, 60 HZ 208 V, 60 HZ 230 V, 50 HZ
Consumption 40 W 40 W 40 W
Operating Current 0.33 A 0.19 A 0 .17 A
POWER I/O U.S./WORLDWIDE UK/EUROPE
Power input connector Neutrik® powerCON® A Neutrik® powerCON® A
Power Cord plug Edison (U.S.) Local Plug
Video
INPUT SPECIFICATIONS OUTPUT PURPOSE
EIA/CEA-861 standard,
1 HDMI
1 DVI-I
1 HD-SDI
meeting HDMI-1.3 stan-
dard, HDCP support
Digital signal,
1080p60fps, HDCP sup-
port
SD/HD/3G-SDI, 480i,
576i, 720p, 1080i/p
4 Neutrik® etherCON® Video Output
1 DVI-I Preview Output
MAXIMUM SUPPORTED RESOLUTION MAXIMUM SUPPORTED LEDS
1920x1080 2,621,440
Connections
INPUT PURPOSE OUTPUT PURPOSE
1 USB Type B
2 Ethernet RJ45 Art-Net™ Connection
Software Connection,
Transfer Presets
1 USB Type A
Software Connection,
Transfer Presets
Control
PC SOFTWARE CONTROL PROTOCOL ART-NET™ CHANNEL RANGE
LED Studio LINSN 95
Thermal
MAXIMUM EXTERNAL TEMPERATURE COOLING SYSTEM
104 °F (40 °C) Convection
Ordering
PRODUCT NAME ITEM NAME ITEM CODE UPC NUMBER
VIP Drive 43s VIPDRIVE43S 21091190 781462215385
VIP Drive 43s User Manual Rev. 1
35
Page 40

RETURNS

RETURNS
Send the product prepaid, in the original box, and with the original packing and accessories. Chauvet will not issue call tags.
Call Chauvet and request a Return Merchandise Authorization (RMA) number before shipping the product. Be prepared to provide the model number, serial number, and a brief description of the cause(s) for the return.
To submit a service request online, go to www.chauvetprofessional.com/service-request Clearly label the package with an RMA number. Chauvet will refuse any product returned without an RMA
number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number directly on the box.
Once you have the RMA number, provide the following information on a pie ce of paper and place it inside the box:
Your name
Your address
Your phone number
RMA number
A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be your responsibility. FedEx packing or double-boxing are recommended.
Chauvet reserves the right to use its own discretion to repair or replace returned product(s).
.
36
VIP Drive 43s User Manual Rev. 1
Page 41

CONTACT US

CONTACT US
World Headquarters
EUROPE
MEXICO
Lerma, Edo. de México, CP 52000
General Information Technical Support
Address: 5200 NW 108th Ave. Voice: (844) 393-7575
Sunrise, FL 33351 Fax: (954) 756-8015
Voice: (954) 577-4455 Email: chauvetcs@chauvetlighting.com
Fax: (954) 929-5560
Toll Free: (800) 762-1084 www.chauvetlighting.com
Website
General Information Technical Support
Address: Stokstraat 18 Email: eutech@chauvetlighting.eu
9770 Kruishoutem
Belgium www.chauvetlighting.eu
Voice: +32 9 388 93 97
Website
General Information Technical Support
Address: Unit 1C Email: uktech@chauvetlighting.com
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT www.chauvetlighting.co.uk
Voice: +44 (0) 1773 511115
Fax: +44 (0) 1773 511110
Website
General Information Technical Support
Av. de las Partidas 34 - 3B, Zona
Industrial Lerma
Email: servicio@chauvet.com.mx
Website
Voice: +52 (728) 285-5000 www.chauvet.com.mx
Visit the applicable website above to verify our contact information and instructions to request support. Outside the U.S., United Kingdom, Ireland, Mexico or Benelux, contact the dealer of record.
VIP Drive 43s User Manual Rev. 1
37
Loading...