Chauvet TFX-950CM User Manual

TFX-950CM

USER MANUAL

Stage Wash™ 950

Chauvet, 3000 N 29

[phone] – [phone]

FAX [phone]

www.chauvetlighting.com

th

Ct, Hollywood, FL 33020 U.S.A

TABLE OF CONTENT

BEFORE YOU BEGIN ...................................................................................................................................................... 3

WHAT IS INCLUDED................................................................................................................................................................................3

UNPACKING INSTRUCTIONS ....................................................................................................................................................................3

AC POWER ..........................................................................................................................................................................................3

SAFETY INSTRUCTIONS.......................................................................................................................................................................... 3

INTRODUCTION............................................................................................................................................................... 4

FEATURES............................................................................................................................................................................................4

DMX CHANNEL SUMMARY..................................................................................................................................................................... 4

PRODUCT OVERVIEW ............................................................................................................................................................................5

SETUP.............................................................................................................................................................................. 6

LAMP ................................................................................................................................................................................................... 6

POWER ................................................................................................................................................................................................ 6

MOUNTING ...........................................................................................................................................................................................7

OPERATING INSTRUCTIONS.......................................................................................................................................... 8

OPERATING MODES ..............................................................................................................................................................................8

Stand Alone Mode.................................................................................................................................................... 8

Master/Slave ............................................................................................................................................................ 9

DMX Mode ............................................................................................................................................................... 9

TFX-SWF Easy Controller (Optional)...................................................................................................................... 11

TFX-CONPK Stage Wash™ Controller Pack (Optional).......................................................................................... 11

APPENDIX...................................................................................................................................................................... 12

DMX PRIMER .....................................................................................................................................................................................12

DMX CHANNEL VALUES ......................................................................................................................................................................13

RGB&D Mode (RGB and Dimmer).......................................................................................................................... 13

C&B Mode (Color and Brightness).......................................................................................................................... 13

RGB and Chase Mode............................................................................................................................................ 13

COLOR MIX TABLE (PRESET) ............................................................................................................................................................... 14

MAINTENANCE ....................................................................................................................................................................................18

RETURNS PROCEDURE........................................................................................................................................................................19

CLAIMS ..............................................................................................................................................................................................19

GENERAL TROUBLESHOOTING..............................................................................................................................................................20

TECHNICAL SPECIFICATIONS ................................................................................................................................................................ 21

TFX-950CM User Manual 2 Revision: 2006-01-20/16:37

Please read these instructions carefully, which includes important informatio

n about the installation,

BEFORE YOU BEGIN

What is included

 1 x Stage Wash™ 950CM (TFX-950CM)
 Power cord with plug
 3 x EHM 300w 120v or 3 x EHM2 300w 230v lamps
 Warranty Card & Manual

Unpacking Instructions

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.

AC Power

To determine the power requirements for a particular fixture, see the label affixed to the back plate of
the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating is its average
current draw under normal conditions. All fixtures must be powered directly off a switched circuit and
cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100% switch. Before applying power to a
fixture, check that the source voltage matches the fixture’s requirement. Check
the fixture or device carefully to make sure that if a voltage selection switch
exists that it is set to the correct line voltage you will use.

AC Voltage Switch

Warning! Verify that the power select switch on your unit matches the

line voltage applied. All fixtures must be connected to circuits
with a suitable Earth Ground.

Safety Instructions

usage and maintenance?

 Please keep this User Guide for future consultation. If you

sell the unit to another user, be sure that they also receive
this instruction booklet.

 Always make sure that you are connecting to the proper

voltage and that the line voltage you are connecting to is
not higher than that stated on decal or rear panel of the
fixture.

 This product is intended for indoor use only!
 To prevent risk of fire or shock, do not expose fixture to

rain or moisture. Make sure there are no flammable
materials close to the unit while operating.

 The unit must be installed in a location with adequate

ventilation, at least 50cm from adjacent surfaces. Be sure
that no ventilation slots are blocked.

 Always disconnect from power source before servicing or

replacing lamp or fuse and be sure to replace with same
lamp source.

Caution! There are no user serviceable parts inside the unit. Do not open the housing or

attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET.

 Secure fixture to fastening device using a safety chain.

Never carry the fixture solely by its head. Use its carrying
handles.

 Maximum ambient temperature is Ta: 40°. Do not operate

fixture at temperatures higher than this.

 In the event of serious operating problem, stop using the

unit immediately. Never try to repair the unit by yourself.
Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest
authorized technical assistance center. Always use the
same type spare parts.

 Don’t connect the device to a dimmer pack.
 Make sure power cord is never crimped or damaged.
 Never disconnect power cord by pulling or tugging on the

cord.

 Avoid direct eye exposure to lamp while it is on.

TFX-950CM User Manual 3 Revision: 2006-01-20/16:37

INTRODUCTION

Features

 2-4 channel DMX RGB color wash fixture
 Operating modes:

RGB Mode: Full RGB mix plus dimmer (4 channels)
C&B Mode: Color selection (40 presets) and dimmer (2 channels)
RGB & Chase Mode: 7 distinct operating modes (4 channels)

- RGB mix, 8-pattern auto, 8-pattern sound, auto-chase, sound-chase, 40-color auto or sound

 Individual channel controls may include;

- Red 0-100%, color selection or mode select

- Green or Red 0-100%, dimmer 0-100%

- Blue or Green 0-100%, fade time

- Dimmer 0-100%, speed time

 900 watts of total brightness
 Built in beat activated and automatic programs (stand-alone)
 Barn doors
 Sound sensitivity knob
 Double bracket yoke doubles as floor stand
 Linkable via Master/Slave
 Fan cooled

DMX Channel Summary

RGB Mode
Channel Function
1 Red
2 Green
3 Blue
4 Dimmer

C&B (Color & Brightness) Mode
Channel Function
1 Color Selection
2 Dimmer

Combined RGB & Chase Mode
Channel Function
1 Control Mode
2 Red or Dimming
3 Green or Fade
4 Blue or Speed

For complete channel listing see DMX Values in the Appendix section.

TFX-950CM User Manual 4 Revision: 2006-01-20/16:37

Introduction

Product Overview

LED status
window

Control panel
buttons

DMX channel
values and brief
instructions

Fan

DMX Input
connector

DMX Output
connector

TFX-950CM User Manual 5 Revision: 2006-01-20/16:37

Sound
sensitivity knob

Foot controller
connector for
TFX-SWF

Built in
microphone

IEC power
connector for
power cable

Voltage
Selector Switch

Fuse
compartment

SETUP

Lamp

You will need to install a lamp prior to the initial operation of the fixture. Three EHM 300W halogen
lamps are included.

Warning! When replacing the lamp, please wait 15 minutes after powering down to allow the

unit to cool down! Always disconnect from main power prior to lamp replacement.

Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp
with alcohol and wipe it with a lint free cloth before installation.

LAMP INST ALLATION

1) Remove the 2 screws as illustrated in Figure 3,
located on the front of the fixture and lift the entire
cover plate until lamp reflectors are exposed.

2) The linear lamp is held in place by tension provided by
springs inside of both ceramic socket ends. It is
important to proceed with lamp removal and
replacement very delicately.

3) Hold linear lamp with a napkin and push in the
direction of either of the two ends to relieve tension on
the opposite end. Then pull end of lamp upwards to
remove from socket.

4) To replace lamp, follow the same procedure as above
to insert lamp into the socket.

5) Lower the cover plate and replace both screws.

6) No lamp alignment is necessary for this fixture.

TFX-950CM Lamp Installation

Remove these 2 screws

Lamps exposed

Power

Your product is equipped with switch-selectable AC power
setting.

Warning! Verify that the power select switch on your unit

matches the line voltage applied. All fixtures must
be connected to circuits with a suitable Earth
Ground.

 To determine the power requirements for a particular fixture,

see the label affixed to the back plate of the fixture or refer to
the fixture’s specifications chart.

 A fixture’s listed current rating is its average current draw under normal conditions.
 All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat (variable

resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100%
switch.

 Before applying power to a fixture, check that the source voltage matches the fixture’s requirement.
 All fixtures must be connected to circuits with a suitable Earth Ground.

Slide switch up or down
depending on your line voltage.

TFX-950CM User Manual 6 Revision: 2006-01-20/16:37

Setup

Clamp is sold separately.

Mounting

ORIENTATION

This fixture may be mounted in any position provided there is adequate room for ventilation.

RIGGING

It is important never to obstruct the fan or vents pathway. Mount the
fixture using, a suitable “C” or “O” type clamp. Adjust the angle of the
fixture by loosening both knobs and tilting the fixture. After finding
the desired position, retighten both knobs.

 When selecting installation location, take into consideration lamp

replacement access and routine maintenance.

 Safety cables should always be used.
 Never mount in places where the fixture will be exposed to rain, high

humidity, extreme temperature changes or restricted ventilation.

DOUBLE BRACKET YOKE (FLOOR STAND)

Hanging Clamp

Note!

The TFX-950CM can also be positioned on the floor using its double bracket yoke. This product gets
extremely hot under normal operation and you should take extreme care to avoid any contact what
so ever with the fixture while in use. Be sure to keep all traffic at least 4 feet away from the fixture’s
position.

TFX-950CM User Manual 7 Revision: 2006-01-20/16:37

AUTO

AUDIO

OPERATING INSTRUCTIONS

Operating Modes

The TFX-950CM can be operated in three ways.

 A stand-alone mode will listen to sound and run through its diverse range of built in programs. An

optional TFX-SWF wired controller provides simple remote control.

 Master/Slave mode will allow the command of up to as many units you want in a synchronized light

show to the sound.

 DMX control mode will provide the greatest flexibility and creativity. Each fixture trait can be controlled

individually using any universal DMX-512 controller.

Stand Alone Mode

The Stand Alone mode is
activated by setting the TFX­950CM to either AUDIO
(Sound Active) or AUTO
(Automatic) mode. The built in
programs consist of a color
chase and depending on the
mode, two or three parameters
can be modified as described
next.

DMX Signal
Received

F:0:0:0

MODE

UP

RGB&D
C & B

DOWN

AUDIO MODE (ALSO SOUND-ACTIVE)

1) A steady hold of the MODE button will change the operating mode once then release the button.

2) Repeat step 1 until you arrive at the AUDIO operating mode, as indicated by the LED next to the
label.

3) Two parameters will now become available for the AUDIO mode. Press the MODE button
quickly to toggle between parameters.

- F (for Fade time 0 ~ 100%)

- D (for Dimming 0 ~ 100%)

4) Use the UP and DOWN buttons to change values for each respective parameter.

AUTOMATIC MODE

1) A steady hold of the MODE button will change the operating mode once then release the button.

2) Repeat step 1 until you arrive at the AUTO operating mode, as indicated by the LED next to the
label.

3) Three parameters will now become available for the AUTO mode. Press the MODE button
quickly to toggle between parameters.

- F (for Fade time 0 ~ 100%)

- D (for Dimming 0 ~ 100%)

- S (for Speed 0 ~ 100%)

4) Use the UP and DOWN buttons to change values for each respective parameter.

TFX-950CM User Manual 8 Revision: 2006-01-20/16:37

Operating Instructions

A:0

:0:

1

AUTO

AUDIO

Master/Slave operation

Master/Slave

The Master/Slave mode will allow you to link up to as many units you want in a daisy chain fashion. In
this mode, the first unit in the daisy chain will automatically command all other units following. An
optional TFX-SWF controller connected to the first unit in the chain will allow enhanced control
functions.

MASTER/SLAVE SETTINGS

1) Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector
of the first fixture.

2) Connect the end of the cable coming from the first fixture which will have a (female) 3 pin
connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then,
proceed to connect from the output as stated above to the input of the following fixture and so on
as illustrated below in figure “Daisy Chain Connection”.

Optional Controller

Controller not required for

Note! For additional information on linking fixtures read under section “DMX Primer”

Daisy Chain Connection

DMX Mode

Operating in a DMX Control mode environment gives the user the greatest flexibility when it comes to
customizing or creating a show. In this mode you will be able to control each individual trait of the
fixture independently.

SETTING THE STARTING ADDRESS

This DMX mode enables the use of a universal DMX controller device. Each fixture requires a "start
address" from 1 to 511. A fixture requiring one or more channels for control begins to read the data
on the channel indicated by the start address. For example, a fixture that occupies or uses 6 channels
of DMX and was addressed to start on DMX channel 100, would read data from channels: 100, 101,
102, 103, 104, and 105. Choose start addresses so that the channels used do not overlap and notate
the start address selected for future reference.

If this is your first time addressing a fixture using the DMX-512 control protocol than I suggest jumping
to the Appendix Section and read the heading “DMX Primer”. It contains very useful information that
will help you understand its use.

There are three different DMX
channel configurations on the
Stage Wash. Each mode or
configuration allows the user to
control the fixure in a different
manner using a universal DMX
controller.

TFX-950CM User Manual 9 Revision: 2006-01-20/16:37

DMX Signal

Received

MODE

UP

DOWN

RGB&D
C & B

Operating Instructions

RGB&D MODE

All three lamps are individually dimmable giving the user
the ability to customize or create the color of choice. This
mode offers the user complete freedom.

1) A steady hold of the MODE button will change the
operating mode once then release the button.

2) Repeat step 1 until you arrive at the RGB&D
operating mode, as indicated by the led next to the
label.

3) The display will now read parameter A: which represents the DMX channel address value. Use
the UP and DOWN buttons to change values.

Channel Function
1 Red
2 Green
3 Blue
4 Dimmer

C&B MODE

This is called the Color and Brightness mode. Use channel
1 to move across the RGB spectrum.

1) A steady hold of the MODE button will change the
operating mode once then release the button.

2) Repeat step 1 until you arrive at the C&B operating
mode, as indicated by the led next to the label.

3) The display will now read parameter A: which
represents the DMX channel address value. Use the UP and DOWN buttons to change values.

Channel Function
1 Spectrum Color Mix
2 Dimmer

See Color Mix Table in the
appendix section.

RGB & CHASE MODE

This is the most diverse operating mode the Stage Wash
has to offer. It allows individual RGB mix control when
needed while still maintaining the ability to run built in
automated chase programs.

1) A steady hold of the MODE button will change the
operating mode once then release the button.

2) Repeat step 1 until both the RGB&D and the C&B led
turn on.

3) The display will now read parameter A: which represents the DMX channel address value. Use
the UP and DOWN buttons to change values.

Channel Function
1 Control Mode
2 Red or Dimming
3 Green or Fade
4 Blue or Speed

TFX-950CM User Manual 10 Revision: 2006-01-20/16:37

Operating Instructions

TFX-SWF Easy Controller (Optional)

The TFX-SWF Foot Controller is used only in master/slave mode. Connect the 8-pin connector of the
foot controller into its respective connector on the first unit in the daisy chain. The table below
describes the functions of the TFX-SWF Controller.

TFX-SWF BUTTONS

TFX-SWF Foot Controller

Stand By Mode Function

Blackout

Auto

Led 1: Off
Led 2: Off

Audio
Led 1: Off

Fixtures will run built in programs
automatically

Fixtures will run built in programs to
the sound.

TFX- WFS

STAND-BY FUNCTION MODE

Led 2: On
Manual

Led 1: On
Led 2: Off

Manual

Led 1: On
Led 2: On

Full/CB:
Hold: pedal to set to Full On
Bump: Pedal to set dimming levels

Full/CB:
Hold: pedal to set dimming levels
Release: Pedal to set to Full On

TFX-CONPK Stage Wash™ Controller Pack (Optional)

The TFX-CONPK is a package that includes the TFX-32CON which is an enhanced dedicated
controller for the TFX-950CM, TFX-64CM and TFX-1550CM fixtures. The TFX-32F foot controller is
also included for hands-free operation.

The TFX-32CON provides the following features:

 9 different hold-color buttons for

immediate color access

 fader access to 40 predefined

mixed colors

 fade time control
 12 different chase patterns to

choose from

 chase speed control
 master dimmer level
 blackout button
 full on button
 sound button

TFX-32 CON

The TFX-32F provides the following features:

 Selectable modes:

1. Blackout

2. Color Hold

TFX-32 F

Mode

3. Chase

 Up and down pedal buttons select

colors and chase patterns

Please refer to the TFX-32CON and TFX-32F user manuals for more in depth information.

TFX-950CM User Manual 11 Revision: 2006-01-20/16:37

COMMON

DMX +

1 3 2 1 3 2 1 3 2

APPENDIX

DMX Primer

There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A
fixture capable of receiving DMX 512 will require one or a number of sequential channels. The user
must assign a starting address on the fixture that indicates the first channel reserved in the controller.
There are many different types of DMX controllable fixtures and they all may vary in the total number
of channels required. Choosing a start address should be planned in advance. Channels should
never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is
set incorrectly. You can however, control multiple fixtures of the same type using the same starting
address as long as the intended result is that of unison movement or operation. In other words, the
fixtures will be slaved together and all respond exactly the same.

DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is
where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which
the fixtures are connected is not important and has no effect on how a controller communicates to
each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures
using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The
shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET
carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’)

FIXTURE LINKING

Figure 1 - DMX connector configuration

INPUT

OUTPUT

Termination reduces signal errors
and to avoid signal transmission
problems and interference, it is

Note! If you use a controller with a 5 pin DMX output connector, you will need to use a 5

pin to 3 pin adapter. Chauvet Model No: DMX5M.
The chart below details a proper cable conversion:

3 Pin to 5 Pin Conversion Chart
Conductor 3 Pin Female (output) 5 Pin Male (Input)
Ground/Shield Pin 1 Pin 1
Data ( - )signal Pin 2 Pin 2
Data ( + ) signal Pin 3 Pin 3
Do not use Do not use
Do not use Do not use

Resistance 120
ohm 1/4w between
pin 2 (DMX -) and
pin 3 (DMX +) of

TFX-950CM User Manual 12 Revision: 2006-01-20/16:37

Appendix

DMX Channel Values

RGB&D Mode (RGB and Dimmer)

Channel Value Function Notes
1

2

3

4

000  255

000  255

000  255

000  255

C&B Mode (Color and Brightness)

Channel Value Function Notes
1

2

000  255

000  255

RGB and Chase Mode

Mode Ch 1 (Mode) Ch 2 Ch 3 Ch 4

RGB Mode 000  029 Red: 0 ~ 100% Green: 0 ~ 100% Blue: 0 ~ 100%
8 Built-in Programs (Auto) 030  094 Speed
8 Built-in Programs (Sound) 094  159
Chase (Auto) 160  184 Speed
Chase (Sound) 185  209
40 Color Chase (Auto) 210  234 Speed
40 Color Chase (Sound) 235  255

Red
Intensity: 0% ~ 100%

Green
Intensity: 0% ~ 100%

Blue
Intensity: 0% ~ 100%

Dimmer
0  100%

Spectrum Color Mix
See Color Mix Table

Dimmer
Intensity: 0% ~ 100%

Dimming:
0 ~ 100%

See Color Mix table on the next
page

Fade Time

TFX-950CM User Manual 13 Revision: 2006-01-20/16:37

Appendix

Color Mix Table (Preset)

DMX Value Red Intensity

0% ~ 100%

0 0 0 0 Blackout
1 100 0 0

2 100 0 0
3 100 3 0

4 100 6 0
5 100 9 0
6 100 12 0
7 100 15 0
8 100 18 0
9 100 21 0
10 100 24 0
11 100 27 0
12 100 30 0
13 100 33 0
14 100 36 0
15 100 39 0
16 100 42 0
17 100 45 0
18 100 48 0
19 100 51 0
20 100 54 0
21 100 57 0
22 100 60 0
23 100 63 0
24 100 66 0
25 100 69 0
26 100 72 0
27 100 75 0
28 100 78 0
29 100 81 0
30 100 84 0
31 100 87 0
32 100 90 0
33 100 93 0

34 100 100 0 Red & Green @ Full
35 97 100 0

36 94 100 0
37 91 100 0
38 88 100 0
39 85 100 0
40 82 100 0
41 79 100 0
42 76 100 0
43 73 100 0
44 70 100 0
45 67 100 0
46 64 100 0
47 61 100 0
48 58 100 0
49 55 100 0
50 52 100 0
51 49 100 0
52 46 100 0
53 43 100 0
54 40 100 0
55 37 100 0
56 34 100 0

Green Intensity
0% ~ 100%

Blue Intensity
0% ~ 100%

Notes

Red @ Full only

Red @ Full
Proportional Green

Green @ Full
Proportional Red

TFX-950CM User Manual 14 Revision: 2006-01-20/16:37

Appendix

57 31 100 0
58 28 100 0
59 25 100 0
60 22 100 0

Green @ Full
Proportional Red

61 19 100 0
62 16 100 0
63 13 100 0
64 10 100 0
65 7 100 0

66 0 100 0

Green @ Full only
67 0 100 0
68 0 100 0
69 0 100 0

70 0 100 3
71 0 100 6
72 0 100 9
73 0 100 12
74 0 100 15
75 0 100 18
76 0 100 21
77 0 100 24
78 0 100 27
79 0 100 30
80 0 100 33
81 0 100 36
82 0 100 39
83 0 100 42
84 0 100 45
85 0 100 48
86 0 100 51
87 0 100 54
88 0 100 57
89 0 100 60
90 0 100 63
91 0 100 66
92 0 100 69
93 0 100 72
94 0 100 75
95 0 100 78
96 0 100 81
97 0 100 84
98 0 100 87
99 0 100 90

Green @ Full

Proportional Blue

100 0 100 93
101 0 100 100 Green & Blue @ Full
102 0 97 100

103 0 94 100
104 0 91 100
105 0 88 100
106 0 85 100
107 0 82 100
108 0 79 100
109 0 76 100
110 0 73 100
111 0 70 100
112 0 67 100
113 0 64 100
114 0 61 100
115 0 58 100
116 0 55 100
117 0 52 100

Blue @ Full

Proportional Green

118 0 49 100

TFX-950CM User Manual 15 Revision: 2006-01-20/16:37

Appendix

119 0 46 100
120 0 43 100
121 0 40 100
122 0 37 100
123 0 34 100
124 0 31 100
125 0 28 100
126 0 25 100
127 0 22 100
128 0 19 100
129 0 16 100
130 0 13 100
131 0 10 100
132 0 7 100

Blue @ Full

Proportional Green

133 0 0 100

Blue @ Full only
134 0 0 100
135 0 0 100
136 0 0 100

137 3 0 100
138 6 0 100
139 9 0 100
140 12 0 100
141 15 0 100
142 18 0 100
143 21 0 100
144 24 0 100
145 27 0 100
146 30 0 100
147 33 0 100
148 36 0 100
149 39 0 100
150 42 0 100
151 45 0 100
152 48 0 100
153 51 0 100
154 54 0 100
155 57 0 100
156 60 0 100
157 63 0 100
158 66 0 100
159 69 0 100
160 72 0 100
161 75 0 100
162 78 0 100
163 81 0 100
164 84 0 100
165 87 0 100
166 90 0 100

Blue @ Full

Proportional Red

167 93 0 100
168 100 0 100 Red & Blue @ Full
169 100 0 97

170 100 0 94
171 100 0 91
172 100 0 88
173 100 0 85
174 100 0 82
175 100 0 79
176 100 0 76
177 100 0 73
178 100 0 70
179 100 0 67
180 100 0 64

Red @ Full

Proportional Blue

TFX-950CM User Manual 16 Revision: 2006-01-20/16:37

Appendix

181 100 0 61
182 100 0 58
183 100 0 55
184 100 0 52
185 100 0 49
186 100 0 46
187 100 0 43
188 100 0 40
189 100 0 37
190 100 0 34
191 100 0 31
192 100 0 28
193 100 0 25
194 100 0 22
195 100 0 19
196 100 0 16
197 100 0 13
198 100 0 10
199 100 0 7

Red @ Full

Proportional Blue

200 100 6 12
201 100 12 24
202 100 18 36
203 100 24 48
204 100 30 60
205 100 36 72
206 100 42 84

Red @ Full

Proportional Green and Blue

207 100 50 100 Red & Blue @ Full, Green @

50%
208 88 62 100

209 76 74 100

Blue @ Full

Proportional Red and Green
210 64 86 100

211 50 100 100 Green & Blue @ Full, Red @

50%
212 44 100 88

213 38 100 76

Green @ Full

Proportional Red and Blue
214 32 100 64
215 26 100 52
216 19 100 44
217 13 100 38
218 7 100 32
219 12 100 25
220 18 100 19
221 24 100 13
222 30 100 7
223 38 100 12
224 44 100 18
225 50 100 24
226 62 100 31
227 74 100 37
228 86 100 43

229 100 100 50 Red and Green @ Full, Blue @

50%
230 100 88 62

231 100 76 74

Red @ Full

Proportional Green and Blue
232 100 64 86

233 100 50 100 Red and Blue @ Full, Green @

50%

TFX-950CM User Manual 17 Revision: 2006-01-20/16:37

Appendix

234 88 44 100
235 76 38 100
236 64 32 100
237 50 25 100
238 44 19 100
239 38 13 100
240 32 7 100
241 25 12 100
242 19 18 100
243 13 24 100
244 7 30 100
245 12 36 100
246 18 42 100
247 24 48 100
248 31 62 100
249 37 74 100
250 43 86 100
251 49 98 100

252 62 100 100
253 74 100 100
254 86 100 100

255 100 100 100 Red,Green,Blue @ FULL

Blue @ Full

Proportional Red and Green

Blue and Green @ Full

Proportional Red

(White)

Maintenance

To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage
and environment are contributing factors in determining frequency. As a general rule, fixtures should
be cleaned at least twice a month. Dust build up reduces light output performance and can cause
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off
fixture before conducting maintenance.

Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust
collected on external vents and internal components. Clean all glass when the fixture is cold with a
mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue. Apply
solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical
surfaces until they are free of haze and lint. Do not to touch the lamp glass when cleaning fixture. Oil
and dirt can cause damage and premature aging of the lamp. In the event that the lamp is touched or
becomes dirty, clean the lamps with an alcohol wipe.

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s
optics. Clean with soft cloth using normal glass cleaning fluid. - Always dry the parts carefully. - Clean
the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.

TFX-950CM User Manual 18 Revision: 2006-01-20/16:37

Appendix

Returns Procedure

Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products
returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief description of the cause
for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate
packaging is the customer’s responsibility. CHAUVET reserves the right to use its own discretion to
repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe
method to use.

Claims

Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.

TFX-950CM User Manual 19 Revision: 2006-01-20/16:37

Appendix

General Troubleshooting

Applies to

Symptom Solution(s)
Auto shut off Check fan thermal switch reset

Beam is very dim or
not bright

Breaker/Fuse keeps
blowing

Chase is too slow Check users manual for speed adjustment
Device has no power Check for power on Mains.

Fixture is not
responding

Fixture is on but there
is no movement to the
audio

Lamps cuts off
sporadically

Light will not come on
after power failure

Loss of signal Use only DMX cables

Moves slow Check 220/110v switch for proper setting
No flash Re-install bulb, may have shifted in shipping
No laser output Bounce mirror motor may have shifted during

No light output Check slip ring & brushes for contact

Relay will not work Check reset switch

Remote does not work Make sure connector is firmly connected to device
Stand alone mode All Chauvet lighting fixtures featuring stand-alone

Clean optical system or replace lamp
Check 220/110v switch for proper setting

Check total load placed on device

Check device’s fuse. (internal and/or external)
Check DMX Dip switch settings for correct

addressing
Check DMX cables
Check polarity switch settings

Make sure you have the correct audio mode on the
control switches. If audio provided via ¼” jack, make
sure a live audio signal exists
Adjust sound sensitivity knob

Possible bad lamp or fixture is overheating.
Lamp may be at end of its life.

Some discharge lamps require a cooling off period
before the electronics in the fixture can kick start it
again, wait 5 to 10 minutes before powering up

Install terminator
Note: Keep DMX cables separated from power
cables or black lights.

shipping, readjust

Install bulb
Call service technician

Check cable connections

functions do not require additional settings, simply
power the fixture and it will automatically enter into
this mode

Lights
















   









 



Foggers
& Snow Controllers

 
 

 

Dimmers&
Chaser

TFX-950CM User Manual 20 Revision: 2006-01-20/16:37

Appendix

Technical Specifications

WEIGHT & DIMENSIONS

Length...........................................................................................................................305 mm (12 in)

Width...............................................................................................................................229 mm (9 in)

Height .............................................................................................................................152 mm (6 in)

Weight.........................................................................................................................5.9 Kg (13.2 lbs)

POWER

Switch-selectable power settings.................................................................115V 60 Hz or 230V 50 Hz

European version............................................................................................................... 240V 50 Hz

AC input.......................................................................................................... 3-prong IEC 60320 C14

LAMPS

3 x EHM (115V)............................................................................................................ 2,000 hr, 300W

3 x EHM2 (230V) ......................................................................................................... 2,000 hr, 300W

.

THERMAL

Maximum ambient temperature......................................................................................... 40° (104° F)

FUSE

Main.................................................................................................30mm Glass 10A 125V Fast Blow

PCB............................................................................................................ 20mm Glass 2A Fast Blow

CONTROL & PROGRAMMING

Data input ............................................................................................. locking 3-pin XLR male socket

Data output........................................................................................ locking 3-pin XLR female socket

Data pin configuration............................................................................pin 1 shield, pin 2 (-), pin 3 (+)

Protocols.....................................................................................................................DMX-512 USITT

DMX Channels.............................................................................................................................2 to 4

ORDERING INFORMATION

Stage Wash™ 950............................................................................................................ TFX-950CM

Stage Wash™ Controller Pack......................................................................................... TFX-CONPK

CA-32F Colormix foot Controller............................................................................................TFX-SWF

Fuse 2A ........................................................................................................................P170FUSE002

Fuse 10A ......................................................................................................................P170FUSE010

TFX-950CM User Manual 21 Revision: 2006-01-20/16:37